Operating Instructions and Parts Manual Box and Pan Brakes Models BPF-1240 and BPF-1450 BPF-1450 shown JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com Part No.
1.0 Warranty and Service JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official JET branded website. • JET products carry a limited warranty which varies in duration based upon the product.
2.0 Table of Contents Section Page 1.0 Warranty and Service ....................................................................................................................... 1 2.0 Table of Contents ............................................................................................................................. 3 3.0 Safety Warnings ............................................................................................................................... 4 4.0 About this manual ......
10. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication. 11. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting wrenches are removed from the machine before using. 3.0 Safety Warnings 1. Read and understand entire owner’s manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury.
4.0 About this manual This manual is provided by JET covering the safe operation and maintenance procedures for a JET BPF-1240 and BPF-1450 Box and Pan Brake. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. Your machine has been designed and constructed to provide consistent, long-term operation if used in accordance with instructions set forth in this document.
.0 Specifications Model Number ...................................................................... BPF-1240 ....................................................BPF-1450 Stock Number ............................................................................752125 ........................................................ 752127 Materials: Frame ......................................................... welded steel plate/tubing ..............................welded steel plate/tubing Clamping fingers .....
.2 Unpacking and cleanup Inspect contents of shipping container for shipping damage. Report any damage to your distributor. Remove all contents from carton, and compare to the contents list in this manual. Report any part shortages to your distributor. Do not discard carton or packing material until machine is assembled and working properly. Exposed metal areas may have a rust protectant applied. Remove this with a soft rag and solvent such as kerosene. (Do not use gasoline, paint thinner, acetone, etc.
.4 General procedure 1. Remove or add clamping fingers as needed for width of material and type of bend. 2. Adjust for setback and clamping pressure. 3. Position stop bolt if needed. 4. Align material in machine and press foot pedal until it locks. 5. Raise bending leaf to desired angle. 6. Lower bending leaf and press foot pedal lock to release material. 9.0 Maintenance Daily wipe down machine with a soft rag. Apply a light coat of SAE 30 oil to exposed metal surfaces to prevent rust.
11.1.
11.1.2 Box and Pan Brake (40” model) – Parts List Index No. Part No. Description Size Qty 1 ................ H40-210 .................... Adjusting Nut .................................................... ............................................. 2 2 ................ H40-215G.................. Clamping Leaf................................................... ............................................. 1 3 ................ H40-224 .................... T-Nut ..........................................
.2.
11.2.2 Box and Pan Brake (50” model) – Parts List Index No. Part No. Description Size Qty 1 ................ H40-210 .................... Adjusting Nut .................................................... ............................................. 2 2 ................ H50-215G.................. Clamping Leaf................................................... ............................................. 1 3 ................ H40-224 .................... T-Nut ..........................................
