Operating Instructions and Parts Manual Pneumatic Sheet Metal Notcher Model PMN-11 JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com Part No.
12. Make all machine adjustments or maintenance with machine unplugged from power source. 13. Use the right tool. Do not force a tool or attachment to do a job that it was not designed to do. 1.0 IMPORTANT SAFETY INSTRUCTIONS 14. Make certain the switch is in the OFF position before connecting the machine to the air or power supply. WARNING – To reduce risk of injury: 1. Read and understand the entire owner’s manual before attempting assembly or operation. 15. Remove adjusting keys and wrenches.
0. Never leave the machine running unattended. Disconnect machine from air supply before leaving the area. the tool. These can present risk of explosion and serious injury. 35. Compressed air can be harmful if directed toward sensitive areas of the body, and may propel small particles caught in the air stream. Exercise proper caution. 31. Do not step on the foot pedal control before or during connection of air supply. 32.
3.0 Table of contents Section Page 1.0 IMPORTANT SAFETY INSTRUCTIONS ....................................................................................................... 2 2.0 About this manual .......................................................................................................................................... 3 3.0 Table of contents ............................................................................................................................................ 4 4.
4.0 Specifications Model number ............................................................................................................................................ PMN-11 Stock number .............................................................................................................................................. 754405 Air supply: Working pressure...................................................................................................................
screws or other appropriate fasteners through two holes in base (inside cabinet). Read and understand the entire contents of this manual before attempting setup or operation! Failure to comply may cause serious injury. 4. 5.0 Setup and assembly Exposed metal surfaces have been given a protective coating. Remove this with a soft cloth and a cleaner-degreaser. Do not use gasoline, paint thinner, acetone, etc., as these may damage painted surfaces.
6.0 Operation 6.1 Controls 2. Turn off air with sliding valve (see B, Figure 52) and bleed residual air from system (see G, Figure 5-2). 3. Release foot pedal. Press foot pedal to activate machine. Cutting head will descend and remain in down position until foot pedal is released. 4. DISCONNECT air supply from machine. 5. An Emergency Stop switch (E-stop) is located atop the foot pedal post; push for immediate shut-down of machine. To restart, rotate E-stop clockwise until it disengages.
3. Drain water from air compressor tank daily, as well as any condensation from air lines. Change filters on the air system on a regular basis. 4. Periodically check filter/regulator bowl (F, Figure 5-2) for fluids or sediment accumulation, and empty if needed. Bowl should be emptied before fluid reaches maximum drain level as indicated on bowl. To remove a bowl, shut off air supply and push pin (G, Figure 5-2) to bleed excess air. Then press tab, rotate bowl to the left, and pull bowl down.
.0 Troubleshooting PMN-11 Pneumatic Notcher Table 2 Symptom Possible Cause Correction Machine will not start. Air valve closed or obstructed. Foot pedal malfunction. Open valve; clear any obstructions. Inspect and replace if needed. Verify compressor has proper CFM rating for tool. Check regulator setting; set air pressure to 115 psi. Check for loose connections. Air supply must be clean and dry. Clean out air hose and remove any kinks or bends. Use materials within rated capacity.
.1.
10.1.2 PMN-11 Pneumatic Notcher – Parts List Index No. Part No. Description Size Qty 1 ................ PMN11-1 ................... Cabinet .................................................................... ...................................... 1 2 ................ PMN11-2 ................... Air Control Unit ........................................................ ...................................... 1 2-1 ............. PMN11-2-1 ................ Pressure Regulator ................................
Index No. Part No. Description Size Qty 56 .............. TS-1541031 .............. Hex Nut, Nylon Lock ................................................ M8 ................................. 1 57 .............. TS-1523021 .............. Socket Set Screw .................................................... M6x8 ............................. 1 58 .............. PMN11-58 ................. Hex Head Bolt.......................................................... M8 ................................. 1 59 ......
11.0 Pneumatic diagram for PMN-11 Notcher Ref.
12.0 Warranty and Service JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official JET branded website. • JET products carry a limited warranty which varies in duration based upon the product.
This page intentionally left blank.
427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.