Use and Care Manual
Table Of Contents
- Vertical Band Saw EVBS-26
- 1.0 WARRANTY AND SERVICE
- 2.0 TABLE OF CONTENTS
- 3.0 SAFETY WARNINGS
- 4.0 INTRODUCTION
- 5.0 SPECIFICATIONS
- 6.0 UNCRATING AND ASSEMBLY
- 7.0 INSTALLATION
- 8.0 ELECTRICAL CONNECTIONS
- 9.0 CONTROLS
- 10.0 ADJUSTMENTS
- 11.0 BLADE SELECTION
- 12.0 WELDER OPERATION
- 13.0 BAND SAW OPERATION
- 14.0 MAINTENANCE
- 15.0 TROUBLESHOOTING
- 16.0 SPEED AND PITCH CHART
- 17.0 REPLACEMENT PARTS —EVBS 26
- 18.0 ELECTRICAL CONNECTIONS — EVBS-26
- 19.0 WIRING DIAGRAM EVBS-26
23
EVBS-26
Material
Sawing speed (Ft/min) for specifi ed Materal and thickness Pitch (No. of teeth/inch)
Thickness ~1/4 1/4~1 1~3 3~6 6~ ~1/4 1/4~1 1~3 3~6 6~
High carbon steel 70 60 60 45 45 18 14 10 6 4
Free cutting steel 60 45 40 30 30 18 14 12 6 4
Ordinary tool steel 40 30 30 25 20 24 18 14 8 4
High speed steel 30 25 20 20 20 24 14 12 8 4
Stainless steel 25 20 20 20 20 18 14 10 8 4
Thick iron plate 45 30 20 20 20 18 14 10 8 4
Cast iron 45 40 30 25 20 18 14 12 8 4
Aluminum 108, A108 365 275 180 120 60 18 10 6 3 3
A132, C133 365 275 180 120 60 18 10 6 3 3
13,43,85,4032,6151 550 425 245 150 90 18 10 6 3 3
113,138,152,B-195 550 380 275 180 90 18 10 6 3 3
B-214,312,333 550 380 275 180 90 18 10 6 3 3
212,355,356,360,380 550 380 275 180 90 18 10 6 3 3
142,195,750 915 825 735 670 610 18 10 6 3 3
2014,2018,2025 915 825 735 670 610 18 10 6 3 3
6053,7075 915 825 735 670 610 18 10 6 3 3
6061,6063 1500 1220 1065 915 770 18 10 6 3 3
122,214,218,220 1500 1385 1220 1065 915 18 10 6 3 3
1100,2011,2017,3003,3004 1500 1500 1500 1385 1220 18 10 6 3 3
2024,5052 1500 1500 1500 1500 610 18 10 6 3 3
Magnesium bronze 125 75 40 25 20 14 8 6 3 3
Leaded commercial bronze 915 610 450 305 150 14 8 6 3 3
Commercial bronze 150 105 60 30 20 14 8 6 3 3
Free cutting brass 1220 915 610 450 300 14 8 6 3 3
Forging brass 610 460 335 245 150 14 8 6 3 3
High leaded brass 1065 825 565 410 260 14 8 6 3 3
Leaded brass 610 460 275 215 150 14 8 6 3 3
Low loaded brass 455 305 150 60 20 14 8 3 3 3
Leaded copper 765 550 360 240 120 14 8 3 3 3
Cadmium copper 90 60 30 25 20 14 8 3 3 3
Magnesium 1500 1385 1220 915 610 14 8 3 3 3
Cadmium 1220 1065 915 915 760 14 8 6 3 3
Manganese 60 45 30 25 20 24 14 6 3 3
Nickel 55 40 30 25 20 18 14 6 3 3
Bdellium 55 45 40 35 25 18 14 6 3 3
Chrome 50 40 25 20 20 18 14 6 3 3
Silicon 55 30 30 20 20 18 14 6 3 3
Carbon (8~35) 1220 1065 915 765 610 10 6 3 3 3
Carbon (35~65) 615 245 90 45 20 14 10 6 3 3
Carbon (1008~1095) 60 45 30 25 20 24 14 6 3 3
Rubber 460 155 90 60 45 18 14 10 8 6
Plastics 1500 1065 765 550 455 10 8 3 3 3
Resimene 1500 1375 1065 915 765 10 8 6 3 3
Leather 1220 1065 915 855 795 14 10 6 4 3
Corkboard 1500 1375 1220 1065 915 18 14 8 6 3
16.0 SPEED AND PITCH CHART
Table 5