Install Instructions

ManualsBrandsJohnson Controls ManualsHeating Supplies8" Adjustable Nickel Wire Temperature Sensor (1k ohm)

Table Of Contents

TE-6300P Series Temperature Sensors Installation Instructions 1

Refer to the QuickLIT website for the most up-to-date version of this document.

Applications

To meet plenum rating where Underwriters

Laboratories Inc.® UL 1995 rating is accepted, replace

the existing thermoplastic cover with the TE-6001-13

Metal Cover. To meet International Mechanical Code

standards, use all-metal components.

Installation

Dimensions

Table 1: TE-6300P Applications

Duct Probe Temperature Sensor

Model Description and Probe, in. (mm)

TE-6311P-1 1k ohm Thin-Film Nickel, 8 (203)

TE-6351P-1 1k ohm Thin-Film Platinum, 8 (203)

TE-6341P-1 2.2k ohm Negative Temperature

Coefficient (NTC) Thermistor, 8 (203)

TE-6361P-1

10k ohm Johnson Controls

® Type II, NTC

Thermistor, 8 (203)

Well Insertion Temperature Sensor

Model Description and Probe, in. (mm)

TE-6312P-1 Threaded 1k ohm Thin-Film Nickel,

8 (203)

TE-631AP-1 Threadless 1k ohm Thin-Film Nickel,

6 (152)

TE-6352P-1 Threaded 1k ohm Thin-Film Platinum,

8 (203)

TE-635AP-1 Threadless 1k ohm Thin-Film Platinum,

6 (152)

Note: See Figure 9 and Figure 10 for threadless

and threaded connections.

Duct Averaging Temperature Sensor

Model Description and Probe, in. (mm)

TE-6315P-1 1k ohm Nickel Wire, 8 (2.4)

TE-6316P-1 1k ohm Nickel Wire, 17 (5.2)

TE-6327P-1 1k ohm Platinum Equivalent Wire,

10 (3.0)

TE-6328P-1 1k ohm Platinum Equivalent Wire,

20 (6.1)

TE-6337P-1 100 ohm Platinum Equivalent Wire,

10 (3.0)

TE-6338P-1 100 ohm Platinum Equivalent Wire,

20 (6.1)

IMPORTANT: The TE-6300P Series Temperature

Sensor is intended to provide an input to equipment

under normal operating conditions. Where failure or

malfunction of the sensor could lead to personal

injury or property damage to the controlled

equipment or other property, additional precautions

must be designed into the control system.

Incorporate and maintain other devices, such as

supervisory or alarm systems or safety or limit

controls, intended to warn of or protect against

failure or malfunction of the sensor.

IMPORTANT: Do not install the TE-6300P Series

Temperature Sensor probe in ambient temperatures

beyond the specified -50 to 220°F (-46 to 104°C)

temperature range. Installing the temperature

sensor probe in ambient temperatures beyond this

range may damage the unit and void the warranty.

Figure 1: Duct Probe Sensor Dimensions, in. (mm)

1/2-14 NPT Threads

TE-6300P Series Temperature Sensors

Installation Instructions

TE-63xxP-1

Part No. 24-4034-107, Rev. L

Issued August 26, 2013

Supersedes January 31, 2013

Summary of content (6 pages)

PAGE 1
TE-6300P Series Temperature Sensors Installation Instructions Part No. 24-4034-107, Rev. L TE-63xxP-1 Issued August 26, 2013 Supersedes January 31, 2013 Refer to the QuickLIT website for the most up-to-date version of this document. Applications To meet plenum rating where Underwriters Laboratories Inc.® UL 1995 rating is accepted, replace the existing thermoplastic cover with the TE-6001-13 Metal Cover. To meet International Mechanical Code standards, use all-metal components.
PAGE 2
. Cut the probe using a tubing cutter with a sharp blade, as shown in Figure 4. (Cut slowly, using minimal pressure to decrease burr size and help avoid damaging the leads.) 2.75 (69.9) Mounting Plate: 3 x 3 (76 x 76) FIG: 6300_dim2 6.0 (152) maximum 1.72 (43.7) 1/2-14 NPT Threads Measure from this end Figure 2: Duct Averaging Sensor Dimensions, in. (mm) FIG: cut_sns 2.75 (69.9) 7.5 (190.5) maximum (8 in.) 5.5 (139.7) maximum (6 in.) Figure 4: Cutting the Sensor Probe 0.52 (13) 3.
PAGE 3
Note: It may be necessary to loosen the set screw and remove the sensor probe to obtain adequate clearance to slide the sensor holder out of the conduit box. Mounting the Temperature Sensors FIG: mnt_cnfg To remove the sensor holder from the conduit box, slide the retainer off of the sensor probe. Push the snap finger toward the center of the sensor holder and pull the holder out of the conduit box.
PAGE 4
Mounting the Well Insertion Sensor The TE-63xxP-1 well models include a sensor holder with built-in thermowell adaptor. No additional well adaptor is required for installation when the sensor is used with TE-6300W thermowells. See Figure 8 and mount the sensor as follows: • TE-6300W-110 (TE-63x2P-1), see Figure 10 and screw the sensor holder into the thermal well (the TE-6300W-110 does not contain thermal grease).
PAGE 5
Wiring For 1k ohm nickel temperature sensors, wire resistance can cause approximately 1F° (0.56C°) of error for every 250 ft (76 m) run of 18 AWG wire, or every 100 ft (31 m) run of 22 AWG wire. For 1k ohm platinum temperature sensors, wire resistance can cause approximately 1F° (0.56C°) of error for every 150 ft (46 m) run of 18 AWG wire, or every 50 ft (15 m) run of 22 AWG wire.
PAGE 6
Technical Specifications TE-6300P Series Temperature Sensors Sensor Reference Resistance Sensor Accuracy Sensor Temperature Coefficient Materials Operating Conditions 1k ohm Thin-Film Nickel 1k ohms at 70°F (21°C) 1k ohm Nickel Averaging 1k ohms at 70°F (21°C) 1k ohm Thin-Film Platinum 1k ohms at 32°F (0°C) 100 ohm Platinum Averaging 100 ohms at 32°F (0°C) 1k ohm Platinum Averaging 1k ohms at 32°F (0°C) 2.