SDS
SECTION
1
1
• IDENTIFICATION
IDENTITY:
GLUEBOARD FLY TRAP
EPA Registration No.
NONE
ACTIVE INGREDIENT CHEMICAL NAME: NONE
CHEMICAL FAMILY: Hot Melt Adhesive/Thermoplastic
Distributor's Name:
J.T. EATON & CO., INC.
1393 East Highland Road
Twinsburg, Ohio 44087
Prepared by: Bart Baker Date Prepared: June 18, 2012
HMIS Rating:
Health: 1
Flammability: 1
Reactivity: 0
Personal Protection: -
Other:
Emergency Telephone Number: 1-800-664-9042 or
National Pesticide Telecommunications Network at 1-800-858-7378
Telephone Number for Information:
9 AM to 5 PM EST - 330-425-7801
SECTION
2
2
HAZARDOUS INGREDIENTS
HAZARDOUS COMPONENTS CAS NUMBER
NONE
<-OSHA LIMITS -> OPTIONAL
PEL STEL CEILING ACGIH TLV %
N/A N/A N/A N/A N/A
1500GB GLUE BOARD
The Occupational Safety and Health Administration (OSHA) Hazard Communication Standard CFR 1910.1200 (Right to Know) requires
manufacturers of hazardous chemicals to provide their customers with Material Safety Data Sheets (MSDS) and employee training
information. To ensure compliance with this law, customers have requested MSDS Forms for the products they are purchasing from
our C
ompany.
In accordance with the Hazard Communications Standard, this product... Glueboard Fly Traps... is defined as an "Article" under this law
(lamps are on a separate MSDS). The standard defines "Articles" as follows (CFR 1910.1200, Section C - Definitions):
"Article" means a manufactured item: (i) which is formed to a specific shape or design during manufacture; (ii) which has end use
function(s)
dependent in whole or in part upon its shape or design during end use; and (iii) which does not release, or other otherwise
result in exposure to, a hazardous chemical, under normal conditions of use.
The Standard further explains that the requirements of this Standard do not apply to "Articles" (Section B - Scope and Application,
Paragraph 5).
Following the intent of this Standard, the following are
the major components of a finished Glueboard Fly Trap:
• Galvanized Steel with Vinyl Covering; or Stainless Steel;
• Screws, bolts, nuts, washers of steel or stainless steel;
• Copper insulated cords/wire and connectors of various types;
• Plated metal grill;
• Black Light Lamps (covered under a separate MSDS);
• Sticky Trap Glueboards.
J.T. EATON & CO., INC. has a firm commitment to comply with the law. Howev
er, the Company is not required under the Hazard
Communications Standard CFR 1910.1200 to provide MSDS Forms for its products. Completion of this form does not constitute an
acknowledgment of its application to the IOC® product.
1393 East Highland Road
Twinsburg, OH 44087 • U.S.A.
SECTION
3
3
• PHYSICAL / CHEMICAL DATA
N/A = Not Applicable
BOILING POINT: (F): N/A
VAPOR PRESSURE: (mm hg): N/A
VAPOR DENSITY: (AIR = 1): N/A
SOLUBILITY IN H
2
O: N/A
SPECIFIC GRAVITY (H
2
O = 1): N/A
BULK DENSITY: N/S
MELTING POINT: N/A
EVAPORATION RATE (Butyl Acetate = 1): N/A
% VOLATILE: N/A
APPEARANCE / ODOR: Clear to pale yellow tacky solid.
Characteristic Odor: Petroleum odor.
SECTION
4
4
• FIRE & EXPLOSION HAZARD DATA
FLASH POINT (Method Used) - N/A
FLAMMABLE LIMITS: N/A LEL: N/A UEL: N/A
EXTINGUISHING MEDIA: N/A
SPECIAL FIRE FIGHTING PROCEDURES: N/A
UNUSUAL FIRE & EXPLOSION HAZARDS: N/A
SECTION
5
5
• REACTIVITY DATA
CHEMICAL STABILITY: N/A
CONDITIONS TO AVOID: N/A
INCOMPATIBLE MATERIALS: N/A
HAZARDOUS POLYMERIZATION: N/A
HAZARDOUS DECOMPOSITION PRODUCTS
(from
burning, heating, or reaction with other materials):
N/A