Lockstitch machine with a long arm and a thread trimmer TL-2200QVP INSTRUCTION MANUAL NOTE: Congratulations on your purchase of a JUKI sewing machine. Please be sure to read this Instruction Manual before operating the sewing machine to ensure safe operation. Please be sure to keep the Instruction Manual so that you can read it whenever necessary.
“IMPORTANT SAFETY INSTRUCTIONS” When using an electrical appliance, basic safety precautions should always be followed, including the following: Read all instructions before using this sewing machine. “DANGER ____ To reduce the risk of electric shock:” 1. The appliance should never be left unattended when plugged in. 2. Always unplug this appliance from the electric outlet immediately after using and before cleaning.
Congratulations on your purchase of a JUKI sewing machine. Please be sure to read safety precautions in “To use the sewing machine safely” in the Instruction Manual before use to fully understand the functions and operating procedures of the sewing machine so as to use the sewing machine for a long time. After you have read the Instruction Manual, please be sure to keep it together with the warranty so that you can read it whenever necessary.
WARNING For the combination of the material and the thread and needle, in particular, refer to the explanation table in “Replacement of the needle”. If the needle or thread does not match the material used such as in the case that an extra heavy-weight material (e.g., denim) is sewn with a thin needle (#11 or higher), the needle can break resulting in an unexpected personal injury. Other precautions ● Do not put the sewing machine under the direct sunlight or in a humid place.
How to carry the sewing machine ■ A How to take out the sewing machine CAUTION If you pull up the sewing machine by holding presser regulating screw section A , the sewing machine can break. In addition, be aware that the presser regulating screw can break if a physical impact is given to it. Pull out the sewing machine from the cutout of styrene foam by holding the main body of the arm. CAUTION Turn OFF the power switch. Always must be disconnected plug from socketoutlet.
GROUNDING INSTRUCTIONS This product must be grounded. In the event of malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
CONTENTS Safety regulations.......................................................................................1-3 How to carry the sewing machine................................................................. 4 GROUNDING INSTRUCTIONS.................................................................... 5 Specifications................................................................................................ 7 Accessories..............................................................................
Specifications Description Specification Sewing speed Max. 2,200 sti/min Needle bar stroke 35mm Lift of presser foot 5.5mm Needle GB 134R Lubricating oil New Defrix Oil No.1 Dimensions of sewing machine 22.2W x 46.0H x 73.0L (cm) Weight of sewing machine 26 kg Rated power supply / Power consumption AC100V-AC240V/1.2A-0.
Accessories 1 2 3 4 5 6 7 8 1. Power cord 2. Exclusive screwdriver 3. Screwdriver (small) 4. Cleaning brush 5. Bobbins (4pcs.) 6. Oiler 7. Needles (GB 134R #18) 8. Spool cap 9. Thread stand components (spool holder, thread stand thread guide, bobbin winder spool pin, bobbin winder seat, anti-vibration cone (2 pcs.), setscrew large, setscrews small (2 pcs.)) 10. Eye protection cover components (safety plate, safety plate mounting plate, washers (2 pcs.), setscrews large (2 pcs.
Setup and operation ■ Basic Operating Procedures 1) Insert the electric power cord plug into the corresponding inlet. Turn ON the power switch. This is described in the Instruction Manual. 2) Set the machine settings from the LCD screen. You can set the maximum sewing speed and the automatic thread trimming at the end of sewing. For details, please refer to the "Stitch Regulator User Manual". Screen of stand-up type Screen of sit-down type 85% 15% 60% 85% <1.
• Precise Stitch Mode The sewing machine won’t sew, even if you press the "start button" on the right handlebar. When you move the sewing machine by the handles, the machine will automatically sew a constant stitch length according to the distance moved. • Manual Stitch Mode When you press the "start button" on the right handlebar, the machine will sew at the maximum sewing speed that has been set. 3 Trimming Thread When you press this button, threads are trimmed automatically. * Start sewing.
<2. Sit-down type> 1 Setting the Maximum Sewing Speed You can set the maximum sewing speed in 5% increments. 85% 15% 60% 85% 2 Auto Thread Trimming Function The sewing machine will trim the threads automatically when it stops. 85% 15% 60% 85% A B 3 Sewing and Manual Thread Trimming When you press part A of the foot controller (pedal), the sewing machine will start sewing. The sewing machine sews at a faster speed according to the amount that part A is pressed.
Principal Parts 7 1 8 2 15 3 9 10 11 17 6 4 12 13 5 16 20 23 24 22 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24.
Name and Function of each component ■ Power cord Insert the electric power cord plug into the corresponding inlet. CAUTION Turn OFF the power switch before insertion/removal of any cords and any plugs. Perform these following steps before you are not using your sewing machine. 1. Turn OFF the power switch. 2. Remove the power plug from the wall outlet. ■ ON Power switch Turn ON the machine, set the power switch to “I”. Turn OFF the machine, set the power switch to “O”.
■ 2 Installing the thread stand CAUTION Turn OFF the power switch. Always must be disconnected plug from socket-outlet. 1 6 1. Insert bobbin winder spool pin 2 into spool holder 1. Fix the former with setscrew 3. 2. Set bobbin winder seat 4 and two anti-vibration cones 5 on spool holder 1. 3. Set thread stand thread guide 6 on the top of bobbin winder spool pin 2. 4. Install thread stand 7 on frame 9 with two setscrews 8.
■ Panel cord binding procedure CAUTION Turn OFF the power switch. Always must be disconnected plug from socket-outlet. 1 1 Remove two setscrews from the presser regulator cover. Remove the presser regulator cover. 2 Place the panel cord as illustrated in the figure. It is necessary to place the panel cord at a position where the cord does not come in contact with the mechanical parts. 3 Align the notch in the cover with the panel cord. 4 Fix the presser regulator cover with the setscrews.
■ 6 Installing the eye protection cover CAUTION Turn OFF the power switch. Always must be disconnected plug from socket-outlet. 2 5 3 4 DANGER Be sure to install the eye protection cover since the cover protects eyes from being injured by a fragment of a broken needle. 1 1. Place eye protection cover 2 and washer 3 in the written order on eye protection cover mounting plate 1 and fix them with setscrew 4. 2. Install eye protection cover mounting plate 1 on frame 6 with two setscrews 5.
■ 1 2 Stoke is increased Upper position: Stroke is 1 to 3 mm Stroke is decreased 3 Lower position: Stroke is 3 to 5 mm 1 ■ 1 Adjusting the presser foot stroke It is possible to adjust the presser foot stroke. Remove presser regulator cover. Loosen nut 1. Shift block 2 upward to increase the stroke, or downward to decrease it. To increase the stroke more, change the position of setscrew 3 of the link arm to the lower position (stroke: 3 to 5 mm).
Winding the bobbin 3 5 4 1 Positioning latches 2 Bobbin winder guide Bobbin presser Bobbin thread winding shaft Thread trimmer retaining plate 1 Installing the thread guide. CAUTION 1 2 3 4 5 Turn OFF the power switch. Raise the support rod fully, turning slightly until the positioning latches engage. Set the large spool over the anti vibration cone. Set the household-type thread onto the spool pin and then insert a spool cap in place.
2 CAUTION Turn OFF the power switch. ■ Take out the bobbin case. 3 ■ Take out the bobbin from the bobbin case. 4 ■ Thread the bobbin winder guide. 5 ■ Installing the bobbin. 1 Bring up the needle. Open the hook cover. Take out the bobbin case. Snap in the latch to let the bobbin come out of the bobbin case. 1 Wind thread on the bobbin clockwise by several turns. 2 Place the bobbin on the bobbin thread winding shaft. 3 Press the bobbin presser. Thread is automatically wound on the bobbin.
6 ■ Upon completion of winding the bobbin. 7 ■ Loading the bobbin into the bobbin case. Return the bobbin presser to its home position. Take out the bobbin. Trim the thread with the thread cutting knife. Snap in the bobbin case latch, and put the bobbin into the bobbin case so that the bobbin runs clockwise. Passing the thread through the slit of the bobbin case, continue passing it under the thread tension spring, and pull out the thread open end about 10cm from the bobbin case.
Adjusting the bobbin winder guide Good Thread unevenly wound around the bobbin would badly affect the bobbin thread tension. Thicker toward downside Loosen the screw of the bobbin winder guide to make adjustment.
Threading the machine CAUTION Turn OFF the power switch before threading or passing thread. 1 2 7 * Bring the thread take-up 7 to the upper end of its stroke. Then, pass the thread through it. Thread take-up 6 8 5 3 4 9 0 1 11 a ■ Pass the thread through the thread guide 1. 3 1 ■ 9 Pass the thread through the thread guides 9 and 0. Thread the needle a. 0 a 2 ■ 7 8 2 Thread the machine head in numerical order, 2 to 8.
Adjusting the thread tension Turn OFF the power switch before taking out the bobbin case or replacing the needle. CAUTION · Adjusting the bobbin case Tension adjusting screw Increase As a measure of the thread tension applied by the bobbin case, when a bobbin (Cotton TEX40) is loaded in the bobbin case, the bobbin should slowly drop by its own weight as illustrated in the figure. * Adjust the needle thread tension in accordance with the bobbin thread tension.
■ 1 Tension controller No. 1 When tension nut No. 1 1 is turned to the right A, the remaining length of thread after thread trimming is shortened. When it is turned to the left B, the remaining length of thread is lengthened. * Be sure to carry out back tacking by several stitches at the beginning of sewing.
Attaching the needle Needle clamp screw CAUTION Turn OFF the power switch. Tightens Attaching the needle 1. Turn OFF the power switch. 2. Lower the presser foot. 3. Move the needle bar up to the highest position of its stroke. 4. Holding a needle with its long groove faced to the left, insert the needle into the needle bar until it will go no further. Then, tighten the needle clamp screw.
Maintenance and lubrication Always must be disconnected plug from socket-outlet before cleaning or lubricating the sewing machine. CAUTION Cleaning the hook ● Turn OFF the power switch. Remove the needle. ● Loosen the screws to remove the throat plate. ● Then clean up the hook components using a cleaning brush. Lubricating the machine 1 Bring the red marker dot to the right front. CAUTION 1. If oil gets in eyes, immediately rinse the oil out with water.
Troubles and Corrective Measures If sewing difficulties occur, make sure the instructions are correctly followed. If a problem still exists, the reminders below help to solve it. Troubles Case Corrective measures Page Stitches are skipped. 1. The needle is bent or the needle point is blunted. 2. The needle has not been attached to the needle bar properly. · Replace the needle. 26 · Attach the needle properly to the needle bar. 26 · Correct the threading. 23 Needle thread breaks. 1.
