MULTI-FORMAT MONITOR DEUTSCH INSTRUCTIONS FRANÇAIS DT-V1900CG ENGLISH BEDIENUNGSANLEITUNG :MULTI-SYSTEM-MONITOR MANUEL D’INSTRUCTIONS :MONITEUR MULTI-FORMAT MANUALE DI ISTRUZIONI :MONITOR MULTI-FORMATI INSTRUCCIONES :MONITOR MULTIFORMATO !" : !"#$ ITALIANO The illustration shows the DT-V1900CG with provided wide mask attached. Die Abbildung zeigt Modell DT-V1900CG mit angebrachtem mitgelieferten Breitformat-Vorsatzrahmen.
INSTRUCTIONS MULTI-FORMAT MONITOR DT-V1900CG Thank you for purchasing this JVC Multi-Format Monitor. Before using it, read and follow all instructions carefully to take full advantage of the monitor’s capabilities. Enter below the Serial No. which is located on the rear of the cabinet. Retain this information for future reference. Model No. : DT-V1900CG Serial No. : CONTENTS SAFETY PRECAUTIONS ........................................................................ 2 CONTROLS AND FEATURES ..........
SAFETY PRECAUTIONS In order to prevent any fatal accidents caused by misoperation or mishandling the monitor, be fully aware of all the following precautions. WARNINGS FCC NOTICE (U.S.A. only) To prevent fire or shock hazard, do not expose this monitor to rain or moisture. Dangerous high voltages are present inside the unit. Do not remove the back cover of the cabinet. When servicing the monitor, contrast qualified service personnel. Never try to service it yourself.
POWER CONNECTION The power supply voltage rating of this product is AC 120 V (For U.S.A. and Canada only) and AC 230 V (For European countries or United Kingdom), the power cord attached conforms to the following power supply voltage and countries. Use only the power cord designated to ensure Safety and EMC regulations of each countries. Power cord Power supply voltage : AC 120 V Countries : U.S.A.
CONTROLS AND FEATURES FRONT VIEW 2 1 3 4 5 7 8 11 12 13 14 MUTING DEGAUSS UNDER SCAN PULSE CROSS COLOR OFF VOLUME MENU SCREENS CHECK ASPECT AREA MARKER 18 19 20 21 22 23 SLOT 1 A DEGAUSS UNDER SCAN PULSE CROSS COLOR OFF MENU SCREENS CHECK ASPECT AREA MARKER SLOT 1 A VOLUME SLOT 2 B C E D E F F 6 INPUT SELECT 1 Tally lamp 9 10 15 16 17 8 EMBEDDED AUDIO channel switch button 2 PHASE adjustment knob Adjusts picture hue.
REAR/SIDE VIEW MAKE SLOT2 26 27 SLOT3 SLOT1 RS-232C 30 28 MAIN POWER 29 Press the COLOR OFF button. The button lights and the screen becomes monochrome. When the COLOR OFF button is pressed while lit, the light goes off and the normal screen is restored. Use this function to confirm the noise in the brightness signal or to confirm the white balance. NOTE: This function is invalid with the RGB-input screen. 15 SCREENS CHECK button/lamp [ Press the SCREENS CHECK button.
CONTROLS AND FEATURES (INPUT CARD: OPTIONAL) 䡵 COMPONENT/RGB INPUT CARD (OPTIONAL: IF-C01COMG) 1 Video input/output terminals Input (IN) and output (OUT) terminals for component (colour difference) or RGB signals. The IN and OUT terminals are bridge-connected. (When no cable is connected to the OUT terminal, the input signal is automatically terminated.
䡵 SDI INPUT CARD (OPTIONAL: IF-C01SDG) 1 Output terminal for a selected component serial digital signal Output terminal for a selected digital signal (the input displayed on the screen). The output signal is cablecompensated. NOTE: When the monitor’s power is OFF, no digital signal is output. SWITCHED OUT 1 SDI 1 IN SDI 2 2 4 Input terminals for the digital signal.
CONTROLS AND FEATURES (INPUT CARD: OPTIONAL) (cont'd) 䡵 HD SDI INPUT CARD (OPTIONAL: IF-C12HSDG) 1 Input and output terminals for HD SDI 1 component serial digital signals E.AUDIO HD SDI 1 Input (IN) and output (OUT) terminals for HD serial digital signals. Select HD SDI 1: press INPUT SELECT A/C/E button IN 1 OUT E.AUDIO HD SDI 2 3 IN 2 2 Input and output terminals for HD SDI 2 component serial digital signals Input (IN) and output (OUT) terminals for HD serial digital signals.
PREPARATION 䡵 INSTALLING THE INPUT CARD 䡵 ATTACHING THE WIDE MASK Optional input cards are necessary to use the functions of this monitor. Before mounting the monitor or connecting other equipment to the monitor, be sure to install the input cards. A wide mask is provided with the monitor. This changes the viewable screen area to the 16:9 aspect ratio. The wide mask cannot be attached to the monitor after the monitor is mounted in a rack. Mount the wide mask before installing the monitor in a rack. 1.
PREPARATION (cont'd) 䡵 ATTACHING THE POWER CORD HOLDER The provided Power Cord Holder prevents accidental disconnection of the AC power cord from the AC inlet. The Power Cord Holder consists of two parts; a case and cover. 1. Attach the Power Cord Holder case to the AC inlet on the back of the monitor with 2 screws (provided). 2 Attach the Power Cord Holder cover to the AC power cord. Press the cover until it clicks. 3.
BASIC MENU OPERATIONS (MAIN MENU, SETUP MENU) 䡵 ABOUT MENU SCREENS This monitor features a MAIN MENU (main menu screen) and a SETUP MENU (setup menu screen). The MAIN MENU contains the functions normally used, and the SETUP MENU contains the settings required for initial setup. FUNCTION SETTING PICTURE SUB ADJ. COLOR TEMP/BAL. SIZE/POSI.ADJ. DISTORTION ADJ.
HOW TO USE “MAIN MENU” 䡵 “MAIN MENU” ITEMS The following items appear in MAIN MENU. Items Functions 1 APERTURE CONTROL Compensates the frequency characteristics of the input video signal. Displays 2 SLOT CONDITION Displays the status of the input cards installed in each of the input card slots. 3 sub menu POSITION Selects the display position of the sub menu superimposed on the screen. 4 AREA MARKER Selects the size marker for the other screen ratio used when the screen ratio is 16:9.
䡵 ITEM CONTENTS AND ADJUSTMENT RANGE/SETTINGS 1. APERTURE CONTROL 3. sub menu POSITION Items LEVEL CONTROL FREQ. sub menu reset : 00 :HIGH EXIT: MENU ADJUST:- + SELECT: 4. AREA MARKER Item : LEVEL Adjustment range : 00 ~ +10 Function : Adjusts the compensate value. The higher the number is, the larger the compensate value gets. Item Settings Function : CONTROL FREQ. : HIGH/LOW/OFF : Adjusts the frequency compensation. HIGH : Compensates the high frequencies.
HOW TO USE “MAIN MENU” (cont'd) 5. AREA MARKER-R : Selects the size marker for the other screen ratio (aspect) used when the screen ratio is 16:9. (for external control) Settings : OFF/16:9/4:3/13:9/14:9/MODE 1/MODE 2 Functions : OFF: The marker is not displayed. 16:9/4:3/13:9/14:9: Displays the marker (a white quadrangle) showing the screen size of each aspect ratio. MODE 1/MODE 2: Displays no markers because these settings will be used for function expansion in the future.
HOW TO USE “SETUP MENU” 䡵 “SETUP MENU” ITEMS Items Functions 1 FUNCTION SETTING Displays the monitor’s power-up time or the total usage time. 2 PICTURE SUB ADJ. Performs approximate adjustments using the control knobs on the front panel. 3 COLOR TEMP./BAL. Sets or adjusts the colour temperature or white balance. 4 SIZE/POSI. ADJ. Adjusts the size or position of the picture. 5 DISTORTION ADJ. Compensates the picture distortion.
HOW TO USE “SETUP MENU” (cont'd) 䡵 ITEM CONTENTS AND ADJUSTMENT RANGE/SETTINGS 1. FUNCTION SETTING Selects the colour system and displays the monitor’s power-up time or the total usage time. button to display Press the the setting menu illustrated on the right. COLOR SYSTEM SYNC SELECT RUSH DELAY TIME TALLY SELECT REMOTE SYSTEM EMBEDDED HOUR METER X100h :AUTO :AUTO :STD.
3. COLOR TEMP./BAL. Sets or adjusts the colour temperature or white balance. Press the button to display the setting menu illustrated on the right. COLOR TEMP. BLUE DRIVE RED DRIVE GREEN CUTOFF BLUE CUTOFF RED CUTOFF sub menu reset EXIT: MENU ADJUST:- + SELECT: Item : BRIGHT Adjustment range : –20 ~ 00 ~ +20 Function : For approximate adjustment of the picture brightness. Before adjustment, set the BRIGHT knob on the front panel to 0.
HOW TO USE “SETUP MENU” (cont'd) 4. SIZE/POSI. ADJ. 5. DISTORTION ADJ. Adjusts the size or position of the picture. Press the button to display the setting menu illustrated on the right. H.SIZE H.POSITION V.SIZE V.POSITION sub menu reset : : : : 00 00 00 00 Compensates the picture distortion. Press the button to display the setting menu illustrated on the right. EXIT: MENU ADJUST:- + SELECT: Item : H.
7. CONTROL LOCK Makes the status of the input signal appear or disappear on the screen. Press the button to display the setting menu illustrated on the right. STATUS DISPLAY 1080/1035 :ON :1080 EXIT: MENU ADJUST:- + SELECT: Item Settings Function Item Settings Function : STATUS DISPLAY : ON/OFF : Makes the format name appear or disappear when signals are input and the signal status appear or disappear when the input signal is changed. ON : The information is displayed.
HOW TO USE EXTERNAL CONTROL 䡵 ABOUT EXTERNAL CONTROL The Multi-Format Monitor has two external control terminals. One is the MAKE/TRIGGER terminal, which allows the monitor to be controlled by the MAKE(make contact) or TRG. (trigger contact) method selected in the function setting. MAKE (make contact system): Controls the function by stable disconnection (terminal open) or short-circuiting (short with GND of 15th terminal) of the controlled terminal. TRG.
䡵 HOW TO USE THE RS-232C TERMINAL You can control the monitor from your PC via the RS-232C terminal. For details on operating the monitor from the PC, consult your dealer or service centre for details. 9 8 7 6 1. Cable Prepare a straight cable with a D-sub connector (9-pin, female) and a D-sub connector (9-pin, male) 5 4 3 2 1 Baud Rate Data Bits Parity Stop Bits Flow Control : : : : : 4800/9600/19200 (factory pre-set; 4800) 8 bits No parity 1 Hardware (RTS/CTS) Pin No.
TROUBLESHOOTING Solutions to common problems related to your monitor are described here. If none of the solutions presented here solve the problem, unplug the monitor and consult a JVC-authorised dealer or service centre for assistance. Points to be checked Problems No power supply No picture with the power on No sound Wrong colour Unnatural picture Shaking picture Measures (Remedy) Is the power plug loosened or disconnected? Firmly insert the power plug.
Points to be checked Measures (Remedy) Reference pages Is the monitor placed or moved close to a speaker or any other device incorporating a magnet? Has the position of the monitor been changed with the power on? Move the device away from the monitor. Press the DEGAUSS button on the front panel to degauss the screen. When degaussing, wait more than 30 minutes for maximum effect. 4 Has the picture position, size or distortion been changed? Adjust the picture size (H SIZE, V SIZE) or position (H.
TROUBLESHOOTING (cont’d) 䡵 SELF-CHECK INDICATIONS When the screen goes blank, and one or more of the INPUT SELECT A through F buttons on the front control panel start blinking... This monitor has a self-check function, which allows it to detect malfunctions and alert you. This makes trouble-shooting easier. Whenever a problem occurs, a combination of “self-check indicators” (INPUT SELECT A through F buttons) will blink and the monitor’s power automatically turns off.
SPECIFICATIONS [Dimensions] 䡲 Remote Inputs : • Point-of-contact connection, 1 line, D-sub connector (15-pin 3-line) • Serial connection, 1 line, D-sub connector (9-pin), compliant to RS-232C 䡲 Audio Output : 1 W (monaural) 䡲 Built-in Speaker : 8 cm round x 1 䡲 Environmental Conditions : Operating temperature : 5°C – 35°C Operating humidity : 20% – 80% (non-condensing) 䡲 Power Requirements : 120 V/230 V AC, 50 Hz/60 Hz 䡲 Power Consumption (120 V/230 V) : 1.8 A/1.0A (when input card is inserted) Max. 2.
SPECIFICATIONS (cont’d) 䡵 Compliant Signal Formats of Each Input Card Input Signals IF-C01PNG IF-C01COMG IF-C01SDG IF-C01HSDG IF-C12HSDG — — — — — — — — Black-and-White (50 Hz/60 Hz) R R R — — — — 480/60i (525i) — 480/60p (525p) — 576/50i — 576/50p — 720/60p (720p) — 1080/50i — 1080/60i (1125i) — 1035/60i (1125i) (*1) — 1080/24psF — R R R R R R R 䡬 R EMBEDDED AUDIO — — NTSC (3.58 MHz) PAL (4.
SPECIFICATIONS (INPUT CARD: OPTIONAL) 䡵 IF-C01COMG: COMPONENT/RGB INPUT CARD Type Inputs/Outputs : Component/RGB input card for Multi-Format Monitor : Component (Y, PB/B-Y, PR/R-Y) or RGB: 1 line, BNC connector x 6 (Y: 1 V (p-p), 75 Ω/PB, B-Y, PR, R-Y, R, G, B: 0.7 V (p-p), 75 Ω) Synchronised signal (HD/CS, VD) : 1 line, BNC connector x 4 (1.0 V – 4.0 V (p-p), 75 Ω) * The input (IN) and output (OUT) terminals are bridge-connected. Auto termination. Audio signal: 1 line (monaural), RCA pin x 2 (0.
SPECIFICATIONS (INPUT CARD: OPTIONAL) (cont’d) 䡵 IF-C01HSDG: HD SDI INPUT CARD Type Inputs/Outputs : HD SDI input card for Multi-Format Monitor : Digital input (HD SDI 1/HD SDI 2): 2 lines, BNC connector x 2 (0.8 V (p-p), 75 Ω) Digital output (SWITCHED OUT): 1 line, BNC connector x 1 (0.8 V (p-p), 75 Ω) Audio signal: 1 line (monaural), RCA pin x 2 (0.5 V (rms), high impedance) * The input (IN) and output (OUT) terminals are bridge-connected.
LCT1002-001B(EN) 27 02.1.
DT-V1900CG MULTI-FORMAT MONITOR VICTOR COMPANY OF JAPAN, LIMITED Printed in Japan 0202-Y-U-VP © 2002 VICTOR COMPANY OF JAPAN, LIMITED LCT1116-001A(EN) 32 02.2.