Memory Recorder Instruction Manual

15
Others
Troubleshooting
Symptom Cause(s)Actions Refer to
Power does not turn
on
Power is supplied from the DC INPUT
terminal of the camcorder.
Attach the battery. The power of the memory recorder
cannot be supplied from the DC INPUT terminal of the
camcorder.
A Page 7
Only the power of the camcorder is turned
AOnB.
It is necessary to turn on the power of the memory recorder
at the same time.
A Page 7
Remaining battery level is insufficient. Charge the battery. A Page 14
Unable to record or
play clip
The IEEE1394 cable is not connected. Connect a GY-HD200/HD250 series camcorder to the
KA-UM100G adapter using an IEEE1394 cable.
A Page 7
The [INT/EXT] switch setting of the
KA-UM100G adapter is inappropriate.
● Set to AEXTB during normal use. (When IEEE1394
connection is made internally without the use of an
external cable, set to AINTB.
● If the ANO SIGNALB message does not disappear even
if the setting is correct, set the switch again to select the
setting. If the message remains displayed, turn off and
on the power again.
A Page 7
The video formats of the camcorder and
memory recorder are not consistent with
each other.
Ensure that the video format of the camcorder and memory
recorder are consistent with each other.
A Page 9
The [IEEE1394] switch of the camcorder is
set to the ADVB end.
Set the [IEEE1394] switch to the AHDVB end.
If the ANO SIGNALB message does not disappear even
after setting to AHDVB, set the switch again. If the message
remains displayed, turn off and on the power again.
A Page 9
A Page 10
Recording does not
start
The camcorder is set to the AVTRB mode. Set to the ACAMB mode using the [CAM/VTR] button. A Page 9
The [1394 REC TRIGGER] item on the
OTHERS[2/2] menu screen of the
camcorder is set to AOFFB or ASERIESB.
Set [1394 REC TRIGGER] to ASYNCROB or ASPLITB.
When this is set to ASERIESB, recording starts when the
remaining capacity of the cassette tape falls below three
minutes.
A Page 9
The memory recorder is set to the playback
mode.
Press the [STOP] button to stop playback. A Page 9
The write-protect of the SxS memory card
is enabled.
Set the write-protect switch to AOffB before recording or
deleting a clip.
A Page 14
There is no space left on the SxS memory
card.
Use an SxS memory card that has sufficient space. A Page 14
Unable to play clip The camcorder is set to the ACAMB mode. Set to the AVTRB mode using the [CAM/VTR] button. A Page 10
The cassette tape is currently being played
back.
Stop playback of the cassette tape before playing back
data on the SxS memory card.
A Page 10
A clip without the check mark (v) is
selected.
Set the camcorder and memory recorder according to the
video format displayed when a clip is selected.
A Page 10
The memory recorder is in the recording or
standby mode.
Press the [STOP] button to stop playback. A Page 10
The clip may be damaged. Execute ARESTOREB using this memory recorder. A Page 14
No response when a
button is pressed
The [OPERATION] menu is set to ALOCKB. Change the [OPERATION] menu setting to AUNLOCKB. A Page 14
A multiple number of buttons are pressed
at the same time, or the same button is hit
repeatedly.
Insert a short pause between each button operation.
^
Access lamp does not
turn on
The SxS memory card is not completely
inserted into the card slot.
Make sure that the SxS memory card is fully inserted into
the slot.
A Page 8
The SxS memory card is inserted with the
label facing the opposite direction.
Identify the face of the SxS memory card with the label,
and make sure that the card is correctly oriented before
inserting.
A Page 8
SxS memory card
cannot be used
A SxS memory card that is formatted by
another device is used.
Execute AFORMATB using this memory recorder. A Page 13
A media that is not supported is inserted. Replace it with a recommended SxS memory card. A Page 14
The clip is faulty. Execute ARESTOREB or AFORMATB using this memory
recorder. If doing so does not eliminate the error, replace it
with a recommended SxS memory card.
A Page 14
Error message
appears on the
camcorder panel
display
ADR-HD100 POWER ?B appears when the
memory recorder is not powered on or is
not connected.
Connect and turn on the power of the memory recorder. A Page 6
A Page 7
AHDD NO 1394 SIGNALB appears if the
camcorder is set to the “CAM” mode when
the memory recorder is in playback mode.
Set the camcorder to the AVTRB mode. A Page 10
AHDD SPACE LOWB appears when the
space on the SxS memory card is
insufficient or an SxS memory card is not
inserted.
Use an SxS memory card that has sufficient space.
^
KA-MR100G_EN.book Page 15 Thursday, February 5, 2009 5:28 PM