ENGLISH FRANÇAIS ESPAÑOL KD-T915BTS / KD-T910BTS / KD-TD91BTS / KD-T91MBS/ KD-T711BT / KD-T710BT / KD-TD71BT / KD-SR86BT CD RECEIVER INSTRUCTION MANUAL RÉCEPTEUR CD MANUEL D’INSTRUCTIONS RECEPTOR CON CD MANUAL DE INSTRUCCIONES For customer Use: Enter below the Model No. and Serial No. which are located on the top or bottom of the cabinet. Retain this information for future reference. Model No. Serial No. B5A-3092-00a [K] JS_JVC_KD_T915BTS_K_C00a.
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. JVCKENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
IC (Industry Canada) Caution This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
Article 4 Right pertaining to the Licensed Software Any and all copyrights and other rights pertaining to the Licensed Software and related documents shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any related documents.
Important Notice concerning the Software -jansson Copyright (c) 2009-2012 Petri Lehtinen
sha2 AUTHOR: Aaron D. Gifford - http://www.aarongifford.com/ Copyright (c) 1995, 1996 Carnegie-Mellon University. All rights reserved. Author: Chris G. Demetriou Copyright (c) 2000-2001, Aaron D. Gifford All rights reserved.
T-Kernel 2.0 This product uses the source code of T-Kernel 2.0 under T-License 2.0 granted by T-Engine Forum (www.tron.org) BSD-3-Clause Copyright (c) 2000-2001, Aaron D. Gifford All rights reserved. You may obtain a copy of the license at https://opensource.org/licenses/BSD-3-Clause THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
Contents Before Use ................................................................................................. 3 References .............................................................................................. 37 Basics ......................................................................................................... 4 Maintenance Getting Started ........................................................................................
Before Use IMPORTANT • To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe Warnings and Cautions in this manual. • Please keep the manual in a safe and accessible place for future reference. WARNING • Do not operate any function that takes your attention away from safe driving. • Do not ingest the battery, Chemical Burn Hazard. The remote control supplied with this product contains a coin/button cell battery.
Basics Faceplate KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS: Volume knob Loading slot Attach Display window* Detach KD-T915BTS: USB cable from the rear of the unit Detach button How to reset KD-T711BT/KD-T710BT/KD-TD71BT/KD-SR86BT: Reset the unit within 5 seconds after detaching the faceplate. KD-T711BT: * Only for illustration purpose. To On the faceplate Turn on the power Press B SRC. • Press and hold to turn off the power. Adjust the volume Turn the volume knob.
Getting Started Basics Remote control (RM-RK52) (supplied for KD-T711BT) • For KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS/KD-T710BT/ KD-TD71BT: This unit can be remotely controlled with an optionally purchased remote control. • For KD-SR86BT: Remote control functions are not available. Remote sensor (Do not expose to bright sunlight.
Getting Started 9 Press to exit. To return to the previous setting item, press 3 [USER S.REMO] (For KD-T711BT) See page 36 for details. . [F/W UPDATE] Set the basic settings [UPDATE SYSTEM] . 1 Press and hold 2 Turn the volume knob to select an item (see the following table), then [F/W UP xxxx] press the knob. 3 Repeat step 2 until the desired item is selected or activated. 4 Press to exit. To return to the previous setting item, press [FACTORY RESET] .
Radio Select a stored station Press one of the number buttons (1 to 6). (or) 1 Press . 2 Turn the volume knob to select a preset number, then press the knob. Other settings Search for a station 1 Press B SRC repeatedly to select FM or AM. 2 Press S / T (or press H / I on the remote control) to search for a station automatically. (or) Press and hold S / T (or press and hold H / I on the remote control) until “M” flashes, then press repeatedly to search for a station manually. .
Radio [SSM] [SSM 01–06]/[SSM 07–12]/[SSM 13–18]: Automatically presets up to 18 stations for FM. “SSM” stops flashing when the first 6 stations are stored. Select [SSM 07–12]/[SSM 13–18] to store the following 12 stations. [IF BAND] [AUTO]: Increases the tuner selectivity to reduce interference noises from adjacent FM stations. (Stereo effect may be lost.) ; [WIDE]: Subjects to interference noises from adjacent FM stations, but sound quality will not be degraded and the stereo effect will remain.
Radio PTY code for FM Radio Data System [NEWS], [AFFAIRS], [INFO], [SPORT], [EDUCATE], [DRAMA], [CULTURE], [SCIENCE], [VARIED], [POP M] (music), [ROCK M] (music), [EASY M] (music), [LIGHT M] (music), [CLASSICS], [OTHER M] (music), [WEATHER], [FINANCE], [CHILDREN], [SOCIAL], [RELIGION], [PHONE IN], [TRAVEL], [LEISURE], [JAZZ], [COUNTRY], [NATION M] (music), [OLDIES], [FOLK M] (music), [DOCUMENT] CD/USB/iPod Insert a disc Eject disc Label side The source changes to CD automatically and playback starts.
CD/USB/iPod Connect an iPod/iPhone USB input terminal Accessory of the iPod/iPhone* iPod/ iPhone To On the faceplate On the remote control Reverse/ Fast-forward Press and hold S / T. Press and hold H / I. Select a track/file Press S / T. Press H / I. Select a folder*1 Press 2 J / 1 K. Press J / K. Repeat play*2 Press 4 B repeatedly. and/or [TRACK REPEAT]/[ALL REPEAT]: Audio CD KD-T915BTS: You can also connect to the USB cable from the rear of the unit (USB input terminal).
CD/USB/iPod Quick search (applicable only for CD source and USB FRONT/USB REAR/USB Select music drive While in USB FRONT/USB REAR/USB source, press 5 MODE repeatedly. Stored songs in the following drive will be played back. • Selected internal or external memory of a smartphone (Mass Storage Class). • Selected drive of a multiple drive device. Select control mode While in iPod FRONT/iPod REAR/iPod USB source (or iPod BT source), press 5 MODE repeatedly. [HEAD MODE]: Control iPod/iPhone from this unit.
AUX Pandora® (except for KD-T711BT) You can listen to music from a portable audio player via the auxiliary input jack. You can listen to Pandora on iPhone/iPod touch (via Bluetooth or via USB input terminal) or Android device (via Bluetooth). Preparation: Select [ON] for [BUILT-IN AUX] in [SOURCE SELECT]. (Page 6) Preparation: • Install the latest version of the Pandora application on your device (iPhone/ iPod touch or Android device), then create an account and log in to Pandora.
Pandora® (except for KD-T711BT) To On the faceplate On the remote control Play back/pause Press the volume knob. Press d. Skip a track Press T. Press I. Select thumbs up or thumbs down* Press 2 J / 1 K. Press J / K. Bookmark current song information Press and hold the volume knob. “BOOKMARKED” appears and the information is stored to your device. • The bookmark is available on your Pandora account but not on this unit. * If thumbs down is selected, the current track is skipped.
Spotify You can listen to Spotify on iPhone/iPod touch (via Bluetooth or via USB input terminal) or Android device (via Bluetooth). Preparation: • Install the latest version of the Spotify application on your device (iPhone/ iPod touch or Android device), then create an account and log in to Spotify. • Select [ON] for [SPOTIFY SRC] in [SOURCE SELECT]. (Page 6) Start listening Accessory of the iPhone/iPod touch* On the faceplate Play back/pause Press the volume knob. Press d.
SiriusXM® Radio Spotify (for KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS) Search for a song or station . 1 Press 2 Turn the volume knob to select a list type, then press the knob. The list types displayed differ depending on the information sent from Spotify. 3 Turn the volume knob to select the desired song or station, then press the knob. You can browse through the list quickly by turning the volume knob quickly.
SiriusXM® Radio (for KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS) Select a stored channel Start listening 1 Press B SRC repeatedly to select SIRIUS XM. 2 Press . “ ” indicator lights up. 3 Turn the volume knob to select a CATEGORY, then press the knob. 4 Turn the volume knob to select a category from the list, then press the knob. If “ALL CHANNELS” is selected, all the available channels will be shown. 5 Turn the volume knob to select a channel, then press the knob.
SiriusXM® Radio (for KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS) SmartFavorites and TuneStart™ User preset channels are initially assigned as the SmartFavorites channels. SmartFavorite channel is available with SXV200 or later SiriusXM tuner models. The SiriusXM Vehicle Tuner automatically buffers the broadcast audio content of the SmartFavorites channels in the background. Using SXV200: This unit can assign a maximum of 6 SmartFavorites channels.
SiriusXM® Radio (for KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS) TuneScan™ [CODE SET] 1 2 3 4 5 6 • [LOCK SETTING] [MATURE CH]: Selects the SiriusXM-defined lock setting. ; [USER DEFINED]: Selects the individual channels the user wants to lock. ; [OFF]: Cancels. [CHANNEL EDIT]*1 1 Turn the volume knob to select a category, then press the knob. 2 Turn the volume knob to select a channel you want to lock, then press the knob. “L” appears in front of the channel number. 3 Press and hold to exit.
Using Other Applications JVC Remote application Default: [XX] You can control the JVC car receiver from iPhone/iPod touch (via Bluetooth or via USB input terminal) or Android device (via Bluetooth) using JVC Remote application. • For more information, visit . [REMOTE APP] [SELECT] [YES]: Selects iPhone/iPod touch to use the application via Bluetooth or connected via USB input terminal. ; [NO]: Cancels.
Bluetooth® • Depending on the Bluetooth version, operating system and the firmware version of your mobile phone, Bluetooth features may not work with this unit. • Be sure to turn on the Bluetooth function of the device to make the following operations. • Signal conditions vary depending on the surroundings.
Bluetooth® • KD-T711BT/KD-T710BT/KD-TD71BT/KD-SR86BT, “ indicator(s) light(s) up. ” and/or “ ” • This unit supports Secure Simple Pairing (SSP). • Up to five devices can be registered (paired) in total. • Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you reset the unit. To delete the paired device, see [DEVICE DELETE] on page 24. • A maximum of two Bluetooth phones and one Bluetooth audio device can be connected at any time.
Bluetooth® The following operations may differ or be unavailable depending on the connected phone. To On the faceplate On the remote control Improve the voice quality First incoming call... Answer a call Press or the volume knob. Press J / K / H / I. Reject a call Press and hold or the volume knob. Press and hold J / K / H / I. Press and hold or the volume knob. Press and hold J / K / H / I. End a call *1 This adjustment will not affect the volume of the other sources.
Bluetooth® Default: [XX] [RECENT CALL] (Applicable only if the phone supports PBAP.) 1 Press the volume knob to select a name or a phone number. • “<” indicates call received, “>“ indicates call made, “M” indicates call missed. • “NO HISTORY” appears if there is no recorded call history or call number. 2 Press the volume knob to call. [PHONEBOOK] (Applicable only if the phone supports PBAP.) 1 Press 2 J / 1 K to select the desired letter (A to Z, 0 to 9, and OTHERS).
Bluetooth® Default: [XX] Store a contact in memory You can store up to 6 contacts into the number buttons (1 to 6). 1 Press to enter Bluetooth mode. 2 Turn the volume knob to select [RECENT CALL], [PHONEBOOK] or [BT MODE] [PHONE SELECT] [AUDIO SELECT] [DIAL NUMBER], then press the knob. 3 Turn the volume knob to select a contact or enter a phone number. If a contact is selected, press the volume knob to show the phone number. 4 Press and hold one of the number buttons (1 to 6).
Bluetooth® Bluetooth compatibility check mode You can check the connectivity of the supported profile between the Bluetooth device and the unit. • Make sure there is no Bluetooth device paired. 1 Press and hold . “BLUETOOTH” “CHECK MODE” appears. “SEARCH NOW USING PHONE” “PIN IS 0000” scrolls on the display. 2 Search and select the name of your receiver (“KD-T915BTS”/ “KD-T910BTS”/“KD-TD91BTS”/“KD-T91MBS”/“KD-T711BT”/ “KD-T710BT”/“KD-TD71BT”/“KD-SR86BT”) on the Bluetooth device within 3 minutes.
Bluetooth® Bluetooth — Audio To On the faceplate [TRACK REPEAT], [ALL REPEAT], [GROUP REPEAT]*1, [REPEAT OFF] [GROUP RANDOM]*1, [ALL RANDOM], [RANDOM OFF] Listen to the audio player via Bluetooth 1 Press B SRC repeatedly to select BT AUDIO (or press SOURCE on the remote control). • For KD-T711BT: Pressing enters BT AUDIO directly. 2 Operate the audio player via Bluetooth to start playback. To On the faceplate On the remote control Play back/pause Press the volume knob. Press d.
AMAZON ALEXA (except for KD-T711BT) Alexa is the cloud-based voice service developed by Amazon. You can ask Alexa to play music, get weather reports, traffic information, control smart home devices, shop on Amazon, search the internet, set reminders and more. Preparation: • Create an account at . • Install the latest version of the Alexa mobile application on your device (iPhone/iPod touch or Android device), then log in to the application.
AMAZON ALEXA (except for KD-T711BT) Start listening While in Alexa idle state... 1 Press Basic operations on the unit to activate Alexa. The display shows: “LISTENING...”. 2 Communicate with Alexa via the connected microphone. (Page 20) 3 During music playback in ALEXA source, you can perform the following operations: Once Alexa connection is established... To On the faceplate 1 Press Play back/pause Press the volume knob. Press d. Reverse skip/ Forward skip Press S / T. Press H / I.
Audio Settings [PRO EQ] Adjusts your own sound settings for each source. • The settings are stored to [USER] in [PRESET EQ]. • The settings made may affect the current settings of [EASY EQ]. [62.5HZ] [LEVEL –09] to [LEVEL +09] ([LEVEL 00]): Adjusts the level to memorize for each source. (Before making an adjustment, select the source you want to adjust.) 1 Press and hold . 2 Turn the volume knob to select an item (see the following table), then press the knob.
Audio Settings [FADER] (Not applicable when 3-way crossover is selected.) [POSITION R15] to [POSITION F15] ([POSITION 00]): Adjusts the front and rear speaker output balance. [BALANCE]*4 [POSITION L15] to [POSITION R15] ([POSITION 00]): Adjusts the left and right speaker output balance. [VOLUME ADJUST] [LEVEL –15] to [LEVEL +06] ([LEVEL 00]): Presets the initial volume level of each source by comparing to the FM volume levels. (Before adjustment, select the source you want to adjust.
Audio Settings KD-T711BT/KD-T710BT/KD-TD71BT: Speaker output settings [SPK/PRE OUT] (Applicable only if [X ' OVER TYPE ] is set to [2-WAY]) (page 30) Setting on [SPK/PRE OUT] Select the output setting for the speakers [SPK/PRE OUT], based on the speaker connection method. [REAR/REAR] Audio signal through lineout terminal REAR/SW Rear speakers output [REAR/SUB.W] (default) Subwoofer output Connection via lineout terminals [SUB.W/SUB.
Audio Settings Crossover settings Below are the available setting items for 2-way crossover and 3-way crossover. 2-way crossover setting items [SPEAKER SIZE] [FRONT] [SIZE] [3.5"]/[4"]/[4.75"]/[5"]/[6.5"]/[6.75"]/[7"]/ [4×6]/[5×7]/[6×8]/[6×9]/[7×10] [TWEETER] [SMALL]/[MIDDLE]/[LARGE]/[NONE] (not connected) CAUTION Select a crossover type according to how the speakers are connected. (Page 46, 47) If you select a wrong type: • The speakers may be damaged.
Audio Settings [SUBWOOFER LPF]*2*3 [SW LPF FRQ] [30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/ [90HZ]/[100HZ]/[120HZ]/[150HZ]/[180HZ]/ [220HZ]/[250HZ]/[THROUGH] [SW LPF SLOPE] [–06DB]/[–12DB]/[–18DB]/[–24DB] [SW LPF PHASE] [REVERSE] (180°)/ [NORMAL] (0°) [SW LPF GAIN] [MID RANGE] [HPF FRQ] [30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/[90HZ]/ [100HZ]/[120HZ]/[150HZ]/[180HZ]/[220HZ]/[250HZ]/ [THROUGH] [HPF SLOPE] [–06DB]/[–12DB] [LPF FRQ] [–08DB] to [00DB] [1KHZ]/[1.6KHZ]/[2.5KHZ]/[4KHZ]/[5KHZ]/[6.
Audio Settings Digital Time Alignment settings Determining the delay time automatically If you specify the distance from the currently set listening position to every speaker, the delay time will be automatically calculated. 1 Set [POSITION] and determine the listening position as the reference point (the reference point for [FRONT ALL] will be the center between the right and left in the front seats). 2 Measure the distances from the reference point to the speakers.
Display Settings Zone identification for brightness settings 4 Press KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS: To return to the previous setting item, press to exit. . Default: [XX] [DISPLAY] [DIMMER] Dims the illumination. [OFF]: Dimmer is turned off. Brightness changes to [DAY] setting. [ON]: Dimmer is turned on. Brightness changes to [NIGHT] setting. (See the following “[BRIGHTNESS]” settings.) [DIMMER TIME]: Set the time to turn on dimmer and to turn off dimmer.
Display Settings [COLOR] (for KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS) [PRESET] [DAY COLOR] [NIGHT COLOR] [COLOR GUIDE] Selects illumination colors for the buttons on different zones separately. 1 Select a zone ([ZONE 1], [ZONE 2], [ALL ZONE]). (See the illustration on page 35.) 2 Select a color for the selected zone. • [COLOR 01] to [COLOR 49] • [USER]: The color you have created for [DAY COLOR] or [NIGHT COLOR] is shown. • [COLOR FLOW01] to [COLOR FLOW03]: Color changes at different speeds.
Learning Steering Remote Control (for KD-T711BT) 6 Press and hold any control keys on your steering remote control which you want to assign. A list of key functions will appear on the display. [NONE] (default)/[MUTE]/[SEEK UP]/[SEEK DOWN]/[VOL UP]/[VOL DOWN]/[MODE]/ [ON HOOK]/[OFF HOOK]/[VOICE]/[ENTER] 7 Turn the volume knob to select a function to assign, then press the knob. The selected key function is assigned to the steering remote control key you have selected in step 6.
References Playable files • Playable audio file: For disc: MP3 (.mp3), WMA (.wma), AAC (.aac) For USB mass storage class device: MP3 (.mp3), WMA (.wma), AAC (.aac), AAC (.m4a), WAV (.wav), FLAC (.
References Change the display information Source name Display information: Main (Supplementary) For MP3/WMA/AAC/WAV/FLAC files: Song title (Artist) Song title (Artist) with Music Synchronization Effect*2 Song title (Album title) Song title (Date) File name (Folder name) File name (Date) Playing time (Date) back to the beginning Each time you press , the display information changes. • If the information is unavailable or not recorded, “NO TEXT”, “NO NAME”, or other information (eg.
References KD-T711BT/KD-T710BT/KD-TD71BT/KD-SR86BT: Main display Clock display Source name Display information: Main FM or AM Frequency Frequency with Music Synchronization Effect* back to the beginning Date For FM Radio Broadcast Data System/FM Radio Data System stations only: Station name/Program type Station name/Program type with Music Synchronization Effect* Radio text Radio text+ Radio text+ song title/Radio text+ artist Frequency Date back to the beginning CD or USB Source name Display informa
Troubleshooting General Sound cannot be heard. “MISWIRING CHECK WIRING THEN PWR ON” appears. Turn the power off, then check to be sure the terminals of the speaker wires are insulated properly. Turn the power on again. “PROTECTING SEND SERVICE” appears. Send the unit to the nearest service center. Source cannot be selected. Check the [SOURCE SELECT] setting. (Page 6) The unit does not work at all. Reset the unit. (Page 4) Radio Correct characters are not displayed.
Troubleshooting 42 Remedy “LOADING” appears when you enter search mode by pressing . This unit is still preparing the iPod/iPhone music list. It may take some time to load, try again later. “NO DISC” Insert a playable disc into the loading slot. “NO DEVICE” Connect a device (USB/iPod/iPhone), and change the source to USB/iPod/iPhone again. “MEMORY FULL” You have reached the maximum storage limit of your iPod/iPhone. “ADD ERROR” New station creation is unsuccessful.
Troubleshooting Your subscription is updated. Press the volume knob to continue. “CODE ERROR” Make sure you have entered the correct pass code. (Page 18) “NO CONTENT” There is insufficient content to start TuneScan. “SCAN CANCEL” Bluetooth® Remedy “SUBSCRIPTION UPDATED – PRESS ENTER TO CONTINUE.” • Search from the Bluetooth device again. • Reset the unit. (Page 4) Bluetooth pairing cannot be made. • Make sure you have entered the same PIN code to both the unit and Bluetooth device.
Installation/Connection Troubleshooting AMAZON ALEXA Symptom Remedy No response from Alexa after the voice input. Amazon cloud was unable to analyze the voice input. Wrong response from Alexa. Alexa misunderstood what was said or did not catch the entire request or sentence spoken. Please try again. (Page 28) “DISCONNECTED” Be sure to connect your smartphone to the unit via Bluetooth. (Page 20) Not able to connect or reconnect to Alexa mobile application.
Installation/Connection Part list for installation Installing the unit (in-dash mounting) (A) Faceplate (×1) (B) Trim plate (×1) (C) Mounting sleeve (×1) (D) Wiring harness (×1) Do the required wiring. (Page 46) Hook on the top side Orientate the trim plate as illustrated before fitting. Dashboard of your car (E) Extraction key (×2) Bend the appropriate tabs to hold the sleeve firmly in place.
Installation/Connection Wiring connection IMPORTANT We recommend installing the unit with a commercially available custom wiring harness specific for your car and leave this job to professionals for your safety. Consult your car audio dealer. Antenna terminal Vehicle dashboard Fuse (10 A) Light blue/yellow Factory wiring harness (vehicle) To the steering wheel remote control adapter Custom wiring harness (separately purchased) Join the same color wires together.
Installation/Connection Connect external components Connect external amplifiers via output terminals Signal cord (not supplied) JVC Amplifier* Output terminals Remote wire (not supplied) No Part 1 For KD-T915BTS: USB cable (DC 5 V 1.5 A) (approx. 1 m/3.3 feet) To remote lead (blue/white) of the wiring harness. (Page 46) 2 For KD-T711BT: Learning steering remote (page 36) 3 Output terminals (See “Connect external amplifiers via output terminals”.
Specifications 8.2 dBf (0.71 μV/75 Ω) Quieting Sensitivity (DIN S/N = 46 dB) 17.2 dBf (2.0 μV/75 Ω) Frequency Response (±3 dB) 30 Hz — 15 kHz Signal-to-Noise Ratio (MONO) 64 dB Stereo Separation (1 kHz) 40 dB CD player Usable Sensitivity (S/N = 20 dB) 530 kHz — 1 700 kHz (10 kHz step) 531 kHz — 1 611 kHz (9 kHz step) USB Usable Sensitivity (S/N = 26 dB) AM Frequency Range 48 87.9 MHz — 107.9 MHz (200 kHz step) 87.5 MHz — 108.0 MHz (50 kHz step) 29 dBμ (28.2 μV) USB Standard USB 1.
Audio Version Bluetooth V4.2 Operating Voltage 12 V DC car battery Frequency Range 2.402 GHz — 2.480 GHz Installation Size (W × H × D) 182 mm × 53 mm × 156 mm (7-3/16" × 2-1/8" × 6-3/16") Net Weight (includes Trimplate, Mounting Sleeve) KD-T915BTS: 1.3 kg (2.9 lbs) RF Output Power (E.I.R.P.) +4 dBm (MAX), Power Class 2 Maximum Communication Range Line of sight approx. 10 m (32.8 ft) Pairing SSP (Secure Simple Pairing) Profile HFP1.7.
Table des matieres Avant l’utilisation .................................................................................... 3 Références............................................................................................... 37 Fonctionnement de base ....................................................................... 4 Entretien Prise en main ............................................................................................
Avant l’utilisation IMPORTANTES • Pour utiliser correctement l’appareil, veuillez ce manuel complément avant de l’utiliser. Il est particulièrement important que vous lisiez et acceptiez les avertissements et les précautions de ce manuel. • Veuillez garder ce manuel dans un endroit sûr et accessible pour une utilisation future. MISE EN GARDE • N’utilisez aucune fonction qui risque de vous distraire de la conduite sure de votre véhicule. • Ne pas ingérer la pile. Risque de brûlures chimiques.
Fonctionnement de base Façade Attachez KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS: Bouton de volume Fente d’insertion Fenêtre d’affichage* Détachez KD-T915BTS: Câble USB à partir de l’arrière de l’appareil Touche de détachement Comment réinitialiser KD-T711BT/KD-T710BT/KD-TD71BT/KD-SR86BT: Réinitialisez l’appareil en moins de 5 secondes après avoir détaché la façade. KD-T711BT: * Uniquement à des fins d’illustration. Pour Sur la façade Mettez l’appareil sous tension Appuyez sur B SRC.
Fonctionnement de base Prise en main Télécommande (RM-RK52) (fourni pour KD-T711BT) • Pour KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS/KD-T710BT/KD-TD71BT: Cet appareil peut être commandé à distance avec une télécommande vendue séparément. • Pour KD-SR86BT: Les fonctions de la télécommande ne sont pas disponibles. Capteur de télécommande (Ne l’exposez Pas à la lumière directe du soleil.
Prise en main 9 Appuyez sur pour quitter. Pour retourner à l’option de réglage précédente, appuyez sur 3 (Pour KD-T711BT) Voir page 36 pour les détails. [USER S.REMO] . [F/W UPDATE] Faites les réglages de base [UPDATE SYSTEM] 1 Maintenez enfoncée . 2 Tournez le bouton de volume pour sélectionner un élément (voir le tableau [F/W UP xxxx] suivant), puis appuyez sur le bouton. 3 Répétez l’étape 2 jusqu’à ce que l’élément souhaité soit sélectionné ou activé.
Radio Sélectionnez une station mémorisée Appuyez sur l’une des touches numériques (1 à 6). (ou) 1 Appuyez sur . 2 Tournez le bouton de volume pour choisir un numéro de préréglage, puis appuyez sur le bouton. Autres paramètres Recherchez une station 1 Appuyez répétitivemenent sur B SRC pour sélectionner FM ou AM. 2 Appuyez sur S / T (ou appuyez sur H / I sur la télécommande) pour rechercher une station automatiquement.
Radio [SSM] Défaut: [XX] [SSM 01–06]/[SSM 07–12]/[SSM 13–18]: Prérègle automatiquement un maximum de 18 stations pour FM. “SSM” s’arrête de clignoter quand les 6 premières stations sont mémorisées. Sélectionnez [SSM 07–12]/ [SSM 13–18] pour mémoriser les 12 stations suivantes. [IF BAND] [SSM] [MONO SET] [ON]: Améliore la réception FM mais l’effet stéréo sera perdu. ; [OFF]: Annulation. [AREA] [N.AMERICA]: Pour l’Amérique du Nord/Centrale/du Sud, intervalles AM/FM: 10 kHz/200 kHz. ; [S.
Radio Code PTY pour FM Radio Data System [NEWS], [AFFAIRS], [INFO], [SPORT], [EDUCATE], [DRAMA], [CULTURE], [SCIENCE], [VARIED], [POP M] (musique), [ROCK M] (musique), [EASY M] (musique), [LIGHT M] (musique), [CLASSICS], [OTHER M] (musique), [WEATHER], [FINANCE], [CHILDREN], [SOCIAL], [RELIGION], [PHONE IN], [TRAVEL], [LEISURE], [JAZZ], [COUNTRY], [NATION M] (musique), [OLDIES], [FOLK M] (musique), [DOCUMENT] CD/USB/iPod Insérez un disque Éjectiez le disque Face portant l’étiquette La source change autom
CD/USB/iPod Connectez un iPod/iPhone iPod/ iPhone Prise d’entrée USB Accessoire du iPod/iPhone* et/ou Pour Sur la façade Sur la télécommande Recherche rapide vers l’arrière/vers l’avant Maintenez enfoncée S / T. Maintenez enfoncée H / I. Sélectionnez une plage ou un fichier Appuyez sur S / T. Appuyez sur H / I. Sélectionnez un dossier*1 Appuyez sur 2 J / 1 K. Appuyez sur J / K. Lecture répétée*2 Appuyez répétitivement sur 4 B.
CD/USB/iPod Sélectionnez le lecteur de musique Quand la source est USB FRONT/USB REAR/USB, appuyez répétitivement sur 5 MODE. Les morceaux mémorisés dans le lecture suivant seront lus. • Mémoire sélectionnée interne ou externe d’un smartphone (Mass Storage Class). • Lecteur sélectionné parmi plusieurs lecteurs. Recherche rapide (applicable uniquement pour la source CD et la source USB FRONT/USB REAR/USB) Si vous avez beaucoup de fichiers, vous pouvez effectuer une recherche rapide parmi eux.
AUX Pandora® (sauf pour KD-T711BT) Vous pouvez écouter de la musique à partir d’un lecteur audio portable via la prise d’entrée auxiliaire. Vous pouvez écouter Pandora à partir d’un iPhone/iPod touch (via Bluetooth ou via la prise d’entrée USB) ou périphérique Android (via Bluetooth). Préparation: Sélectionnez [ON] pour [BUILT-IN AUX] dans [SOURCE SELECT].
Pandora® (sauf pour KD-T711BT) Pour Sur la façade Sur la télécommande Lecture/pause Appuyez sur le bouton de volume. Appuyez sur d. Sauter une plage Appuyez sur T. Appuyez sur I. Sélectionnez un pouce vers le haut ou vers le bas* Appuyez sur 2 J / 1 K. Appuyez sur J / K. Enregistrez un signet sur le morceau actuel Maintenez enfoncé le bouton de volume. “BOOKMARKED” apparaît et l’information est mémorisée sur votre périphérique.
Spotify Vous pouvez écouter Spotify à partir d’un iPhone/iPod touch (via Bluetooth ou via la prise d’entrée USB) ou périphérique Android (via Bluetooth). Préparation: • Installez la dernière version de l’application Spotify sur votre appareil (iPhone/ iPod touch ou périphérique Android), puis créez un compte et connectez-vous sur Spotify. • Sélectionnez [ON] pour [SPOTIFY SRC] dans [SOURCE SELECT]. (Page 6) Démarrez l’écoute 1 Démarrez l’application Spotify sur votre appareil.
Radio SiriusXM® Spotify (pour KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS) Recherche d’un morceau ou d’une station 1 Appuyez sur . 2 Tournez le bouton de volume pour choisir un type de liste, puis appuyez sur le bouton. Les types de liste affichés diffèrent en fonction des informations envoyées par Spotify. 3 Tournez le bouton de volume pour sélectionner le morceau ou la station souhaité, puis appuyez sur le bouton. Vous pouvez parcourir la liste rapidement en tournant le bouton de volume rapidement.
Radio SiriusXM® (pour KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS) Démarrez l’écoute 1 Appuyez répétitivement sur B SRC pour sélectionner SIRIUS XM. 2 Appuyez sur . L’indicateur “ ” s’allume. 3 Tournez le bouton de volume pour choisir CATEGORY, puis appuyez sur le bouton. 4 Tournez le bouton de volume pour choisir une catégorie dans la liste, puis appuyez sur le bouton. Si “ALL CHANNELS” est sélectionné, tous les canaux disponibles sont affichés.
Radio SiriusXM® (pour KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS) SmartFavorites et TuneStart™ Les canaux préréglés de l’utilisateur sont affectés initialement comme canaux SmartFavorites. Les canaux préférés intelligents sont disponibles avec le tuner SiriusXM SXV200 ou ultérieur. Le tuner SiriusXM Vehicle met automatiquement en cache le contenu audio diffusé des canaux SmartFavorites en tache de fond. Utilisation de SXV200: Cet appareil peut affecter un maximum de six canaux SmartFavorites.
Radio SiriusXM® (pour KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS) TuneScan™ [CODE SET] 1 2 3 4 5 6 Appuyez sur le bouton de volume pour entrer [NEW CODE]. Tournez le bouton de volume pour sélectionner un numéro. Appuyez sur S / T pour déplacer la position d’entrée. Répétez les étapes 2 et 3 pour entrer un nouveau code secret de 4 chiffres. Appuyez sur le bouton de volume pour valider. Répétez les étapes 2 à 5 pour confirmer le code secret.
Utilisation d’autres applications Application JVC Remote Défaut: [XX] Vous pouvez commander l’autoradio JVC à partir d’un iPhone/iPod touch (via Bluetooth ou via la prise d’entrée USB) ou d’un périphérique Android (via Bluetooth) en utilisant l’application JVC Remote. • Pour plus d’informations, consultez . [REMOTE APP] [SELECT] [IOS] Préparation: Installez la dernière version de l’application JVC Remote sur votre périphérique avant la connexion.
Bluetooth® • En fonction de la version Bluetooth, du système d’exploitation et de la version du micrologiciel de votre téléphone portable, la fonction Bluetooth peut ne pas fonctionner avec cet appareil. • Assurez-vous d’activer la fonction Bluetooth du périphérique pour réaliser les opérations suivantes. • La condition du signal varie en fonction de l’environnement.
Bluetooth® • KD-T711BT/KD-T710BT/KD-TD71BT/KD-SR86BT, l’indicateur “ “ ” s’allume. ” et/ou • Cet appareil prend en charge le Pairage simple sécurisé (SSP). • Un maximum de cinq appareils peuvent être enregistrés (appariés) en tout. • Une fois que le pairage est termine, le périphérique Bluetooth reste enregistré sur l’appareil même si vous réinitialisez l’appareil. Pour supprimer un périphérique apparié, voir [DEVICE DELETE] à la page 24.
Bluetooth® Les opérations suivantes peuvent différer ou peuvent ne pas être disponibles en fonction du téléphone connecté. Pour Sur la façade Sur la télécommande Amélioration de la qualité des voix Premier appel entrant... Répondre à un appel Refuser un appel Fin d’un appel Appuyez sur ou sur le bouton de volume. Appuyez sur J / K / Quand vous parlez au téléphone... H / I. 1 Maintenez enfoncée .
Bluetooth® Défaut: [XX] [RECENT CALL] (Applicable uniquement quand le téléphone prend en charge PBAP.) 1 Appuyez sur le bouton de volume pour sélectionner un nom ou un numéro de téléphone. • “<” indique l’appel reçu, “>” indique un appel passé, “M” indique un appel manqué. • “NO HISTORY” apparaît s’il n’y a pas d’historique d’appels enregistré ou de numéro d’appel. 2 Appuyez sur le bouton de volume pour appeler. [PHONEBOOK] (Applicable uniquement quand le téléphone prend en charge PBAP.
Bluetooth® Défaut: [XX] Stockage d’un contact en mémoire Vous pouvez mémoriser un maximum de 6 contacts sur les touches numériques (1 à 6). 1 Appuyez sur pour entrer en mode Bluetooth. 2 Tournez le bouton de volume pour choisir [RECENT CALL], [PHONEBOOK] ou [DIAL NUMBER], puis appuyez sur le bouton. [BT MODE] [AUDIO SELECT] Permet de sélectionner le téléphone ou le périphérique audio à connecter ou déconnecter. “ ” apparaît devant le nom de l’appareil quand il est connecté.
Bluetooth® Mode de vérification de la compatibilité Bluetooth Vous pouvez vérifier la connectivité du profile pris en charge entre le périphérique Bluetooth et l’appareil. • Assurez-vous qu’il n’y aucun périphérique Bluetooth apparié. 1 Maintenez enfoncée . “BLUETOOTH” “CHECK MODE” apparaît. “SEARCH NOW USING PHONE” “PIN IS 0000” défile sur l’affichage.
Bluetooth® Bluetooth — Audio Pour Sur la façade Lecture répétée Appuyez répétitivement sur 4 B. [TRACK REPEAT], [ALL REPEAT], [GROUP REPEAT]*1, [REPEAT OFF] Lecture aléatoire [GROUP RANDOM]*1, [ALL RANDOM], [RANDOM OFF] Quand la source est BT AUDIO, vous pouvez vous connecter à cinq périphériques audio Bluetooth et commuter parmi ces cinq périphériques. Écoute du lecteur audio via Bluetooth 1 Appuyez répétitivement sur B SRC pour sélectionner BT AUDIO (ou appuyez sur SOURCE sur la télécommande).
AMAZON ALEXA (sauf pour KD-T711BT) Alexa le le service vocal de cloud mis au point par Amazon. Vous pouvez demander à Alexa de lire de la musique, d’obtenir des bulletins météo, des informations routières, de commander des périphériques de maison intelligente, de faire des achat sur Amazon, de faire des recherches sur Internet, de programmer des rappels, etc. Préparation: • Créez un compte sur .
AMAZON ALEXA (sauf pour KD-T711BT) Démarrez l’écoute Quand Alexa est en attente... 1 Appuyez sur sur l’appareil pour activer Alexa. L’affichage montre: “LISTENING...”. 2 Communiquez avec Alexa via le microphone connecté. (Page 20) 3 Pendant la lecture de musique avec la source ALEXA, vous pouvez réaliser les opérations suivantes. Opérations de base Pour Sur la façade Sur la télécommande Lecture/pause Appuyez sur le bouton de volume. Appuyez sur d.
Réglages audio Ajuste vos propres réglages sonores pour chaque source. • Les réglages sont mémorisés sur [USER] dans [PRESET EQ]. • Les réglages réalisés peuvent affecter les réglages actuels de [EASY EQ]. [PRO EQ] [62.5HZ] [LEVEL –09] à [LEVEL +09] ([LEVEL 00]): Réglez le niveau à mémoriser pour chaque source. (Avant de réaliser un ajustement, choisissez la source que vous souhaitez ajuster.) 1 Maintenez enfoncée .
Réglages audio [FADER] (Non applicable quand la transition 3 voies est sélectionnée.) [POSITION R15] à [POSITION F15] ([POSITION 00]): Règle la balance de sortie des enceintes avant et arrière. [BALANCE]*4 [POSITION L15] à [POSITION R15] ([POSITION 00]): Règle la balance de [VOLUME ADJUST] [LEVEL –15] à [LEVEL +06] ([LEVEL 00]): Prérègle le niveau de volume [AMP GAIN] [LOW POWER]: Limite le volume maximum à 25.
Réglages audio KD-T711BT/KD-T710BT/KD-TD71BT: Réglages de sortie d’enceinte [SPK/PRE OUT] (Applicable uniquement si [X ‘ OVER TYPE ] est réglé sur [2-WAY]) (page 30) Réglage sur Sélectionnez le réglage de sortie pour les enceintes [SPK/PRE OUT], sur la base de la méthode de connexion des enceintes. [REAR/REAR] Connexion via les prises de sortie de ligne Pour les connexions via un amplificateur extérieur (Page 47) KD-T915BTS/KD-T91MBS: [REAR/REAR] (défaut) [SUB.W/SUB.
Réglages audio Réglages de transition Voici les options de réglage disponibles pour la transition 2 voies et la transition 3 voies. AVERTISSEMENT Sélectionnez un type de transition en fonction de la connexion de vos enceintes. (Page 46, 47) Si vous sélectionnez une mauvais type: • Les enceintes peuvent être endommagées. • Le niveau sonore de sortie peut être extrêmement élevé ou faible.
Réglages audio [SUBWOOFER LPF]*2*3 [SW LPF FRQ] [30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/ [90HZ]/[100HZ]/[120HZ]/[150HZ]/[180HZ]/ [220HZ]/[250HZ]/[THROUGH] [SW LPF SLOPE] [–06DB]/[–12DB]/[–18DB]/[–24DB] [SW LPF PHASE] [REVERSE] (180°)/ [NORMAL] (0°) [SW LPF GAIN] [MID RANGE] [HPF FRQ] [30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/[90HZ]/ [100HZ]/[120HZ]/[150HZ]/[180HZ]/[220HZ]/[250HZ]/ [THROUGH] [HPF SLOPE] [–06DB]/[–12DB] [LPF FRQ] [–08DB] à [00DB] [1KHZ]/[1.6KHZ]/[2.5KHZ]/[4KHZ]/[5KHZ]/[6.
Réglages audio Réglages de l’alignement temporel numérique Détermination automatique du temps de retard Si vous spécifiez la distance à partir de la position d’écoute actuellement réglée pour n’importe quelle enceinte, le temps de retard est calculé automatiquement. 1 Réglez [POSITION] et déterminez la position d’écoute comme point de référence (le point de référence pour [FRONT ALL] est le centre entre les sièges avant droite et gauche).
Réglages d’affichage Identification de zone pour les réglages de la luminosité 4 Appuyez sur KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS: Pour retourner à l’option de réglage précédente, appuyez sur pour quitter. . Défaut: [XX] [DISPLAY] [DIMMER] Assombrit l’éclairage. [OFF]: Le gradateur est désactivé. La luminosité change sur le réglage [DAY]. [ON]: Le gradateur est activé. La luminosité change sur le réglage [NIGHT]. (Reportez-vous aux réglages “[BRIGHTNESS]” ci-après.
Réglages d’affichage [COLOR] (pour KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS) [PRESET] [DAY COLOR] [NIGHT COLOR] [COLOR GUIDE] Sélectionnez les couleurs d’éclairage séparément pour les touches sur des différentes zones. 1 Choisissez une zone ([ZONE 1], [ZONE 2], [ALL ZONE]). (Voir l’illustration de la page 35.) 2 Choisissez une couleur pour la zone sélectionnée. • [COLOR 01] à [COLOR 49] • [USER]: La couleur que vous avez créée pour [DAY COLOR] ou [NIGHT COLOR] apparaît.
Télécommande de volant à apprentissage (pour KD-T711BT) 6 Maintenez enfoncée la touche de commande votre télécommande de volant à laquelle vous souhaitez affecter la fonction. Une liste des fonctions disponibles apparaît sur l’affichage. [NONE] (défaut)/[MUTE]/[SEEK UP]/[SEEK DOWN]/[VOL UP]/[VOL DOWN]/[MODE]/ [ON HOOK]/[OFF HOOK]/[VOICE]/[ENTER] 7 Tournez le bouton de volume pour sélectionner la fonction à affecter, puis appuyez sur le bouton.
Références Fichiers pouvant être lus À propos de Pandora • Fichier audio reproductible: Pour les disques: MP3 (.mp3), WMA (.wma), AAC (.aac) Pour les périphériques USB à mémoire de grande capacité: MP3 (.mp3), WMA (.wma), AAC (.aac), AAC (.m4a), WAV (.wav), FLAC (.
Références Changez l’information sur l’affichage Nom de la source Informations sur l’affichage: Principal (supplémentaire) Pour les fichiers MP3/WMA/AAC/WAV/FLAC: Titre de morceau (Artiste) Titre de morceau (Artiste) avec effet de synchronisation musicale*2 Titre de morceau (Titre d’album) Titre de morceau (Date) Nom de fichier (Nom de dossier) Nom de fichier (Date) Durée de lecture (Date) retour au début Chaque fois que vous appuyez sur , les informations affichées changent.
Références KD-T711BT/KD-T710BT/KD-TD71BT/KD-SR86BT: Affichage principal Affichage de l’horloge Nom de la source Informations sur l’affichage: Principal FM ou AM Fréquence Fréquence avec effet de synchronisation musicale* Date retour au début Pour les stations FM Radio Broadcast Data System/FM Radio Data System uniquement: Nom de la station/Type de programme Nom de la station/Type de programme avec effet de synchronisation musicale* Radio texte Radio texte+ Radio texte+ titre de morceau/Radio texte+ art
Guide de dépannage Symptôme Radio Symptôme Remède L’ordre de lecture n’est pas celui que vous pensiez. L’ordre de lecture est déterminé par l’ordre dans lequel les fichiers ont été enregistrés (disque) ou par le nom du fichier (USB). La durée de lecture écoulée n’est pascorrecte. Cela dépend du processus d’enregistrement utilisé (disque/ USB). Vérifiez si la plage est dans un format compatible. (Page 37, 38) “MISWIRING CHECK WIRING THEN PWR ON” apparaît.
Guide de dépannage 42 Cet appareil continue de préparer la liste des morceaux de l’iPod/iPhone. Le chargement des données peut être long, essayez de nouveau plus tard. “NO DISC” Insèrez un disque reproductible dans la fente d’insertion. “NO DEVICE” Connectez un périphérique (USB/iPod/iPhone), puis repassez à la source USB/iPod/iPhone. “MEMORY FULL” Vous avez atteint la limite maximum de mémoire de votre iPod/iPhone. “ADD ERROR” La création d’une nouvelle station n’a pas réussie.
Guide de dépannage Remède “SUBSCRIPTION UPDATED – PRESS ENTER TO CONTINUE.” Votre abonnement a été mis à jour. Appuyez sur le bouton de volume pour continuer. “CODE ERROR” Assurez-vous que vous avez entré le code secret correct. (Page 18) “NO CONTENT” Le contenu est insuffisant pour démarrer TuneScan. “SCAN CANCEL” TuneScan a été interrompu. Aucun périphérique Bluetooth n’est détecté. • Faites de nouveau une recherche à partir du périphérique Bluetooth. • Réinitialisez l’appareil.
Installation/Connexion Guide de dépannage AMAZON ALEXA Symptôme Remède Aucune réponse d’Alexa après l’entrée vocale. Amazon cloud n’a pas été capable d’analyser l’entrée vocale. Mauvaise réponse d’Alexa. Alexa n’a pas compris ce que vous avez dit ou n’a pas reçu toute la requête ou la phrase parlée. Essayez de nouveau. (Page 28) “DISCONNECTED” Impossible de connecter ou de reconnecter l’application Alexa mobile. Assurez-vous de connecter votre smartphone à l’appareil via Bluetooth.
Installation/Connexion Liste des pièces pour l’installation Installation de l’appareil (montage encastré) (A) Façade (×1) (B) Plaque de garniture (×1) (C) Manchon de montage (×1) (D) Faisceau de fils (×1) Réalisez les connexions nécessaires. (Page 46) Crochet sur le côté supérieur Orientez la plaque de garniture de la façon illustrée avant la fixation. Tableau de bord de votre voiture (E) Clé d’extraction (×2) Tordez les languettes appropriées pour maintenir le manchon en place.
Installation/Connexion Connexions IMPORTANTES Nous recommandons d’installer l’appareil en utilisant un harnais de câblage en vente dans le commerce recommandé spécifiquement pour votre voiture et, pour votre sécurité, de laisser ce travail a des professionnels. Consultez votre revendeur autoradio.
Installation/Connexion Connexion d’appareils extérieurs Connectez les amplificateurs extérieurs via les prises de sortie Cordon de signal (non fournie) JVC Amplificateur* Prises de sortie Fil de télécommande (non fournie) No. Pièce 1 Pour KD-T915BTS: Câble USB (CC 5 V 1,5 A) (environ 1 m/3,3 pieds) Au fil de télécommande (bleu/blanc) du faisceau de fils.
Spécifications 8,2 dBf (0,71 μV/75 Ω) Seuil de sensibilité (DIN S/B = 46 dB) 17,2 dBf (2,0 μV/75 Ω) Réponse en fréquence (±3 dB) 30 Hz — 15 kHz Taux de Signal/Bruit (MONO) 64 dB Séparation stéréo (1 kHz) 40 dB Lecteur CD Sensibilité utilisable (S/B = 20 dB) 530 kHz — 1 700 kHz (pas de 10 kHz) 531 kHz — 1 611 kHz (pas de 9 kHz) USB Sensibilité utilisable (S/B = 26 dB) AM Plage de fréquences 48 87,9 MHz — 107,9 MHz (pas de 200 kHz) 87,5 MHz — 108,0 MHz (pas de 50 kHz) 29 dBμ (28,2 μV) Diode
Audio Bluetooth Spécifications Bluetooth V4.2 Tension de fonctionnement Batterie de voiture 12 V CC Plage de fréquences 2,402 GHz — 2,480 GHz Dimensions d’installation (L × H × P) Puissance de sortie RF (E.I.R.P.
Contenido Antes del uso ............................................................................................ 3 Referencias ............................................................................................. 37 Puntos básicos ......................................................................................... 4 Mantenimiento Procedimientos iniciales ........................................................................
Antes del uso IMPORTANTE • Antes de utilizar este producto y para asegurar su uso correcto, lea completamente este manual. En especial, lea y acate las Advertencias y Precauciones incluidas en este manual. • Guarde el manual en un lugar seguro y accesible para futuras consultas. ADVERTENCIA • No utilice ninguna función que pueda desviar su atención mientras está conduciendo el vehículo. • No ingiera la pila, existe riesgo de quemaduras por productos químicos.
Puntos básicos Placa frontal KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS: Rueda de volumen Ranura de carga Fijar Ventanilla de visualización* Desmontar KD-T915BTS: Cable USB de la parte trasera de la unidad Botón de liberación Cómo reinicializar KD-T711BT/KD-T710BT/KD-TD71BT/KD-SR86BT: Reinicialice la unidad en menos de 5 segundos después de haber extraído la placa frontal. KD-T711BT: * Solo para fines ilustrativos. Para En la placa frontal Encender la unidad Pulse B SRC.
Procedimientos iniciales Puntos básicos Mando a distancia (RM-RK52) (suministrado para KD-T711BT) • Para KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS/KD-T710BT/ KD-TD71BT: Esta unidad puede controlarse a distancia mediante un mando a distancia adquirido a opción. • Para KD-SR86BT: Las funciones del mando a distancia no están disponibles. Sensor remoto (DO lo exponga a la luz solar brillante.
Procedimientos iniciales 9 Pulse para salir. Para volver al elemento de ajuste anterior, pulse 3 (Para KD-T711BT) Para más detalles, consulte la página 36. [USER S.REMO] . [F/W UPDATE] Realice los ajustes básicos [UPDATE SYSTEM] 1 Pulse y mantenga pulsado . 2 Gire la rueda de volumen para seleccionar un elemento (consulte la [F/W UP xxxx] siguiente tabla) y, a continuación, pulse la rueda. 3 Repita el paso 2 hasta que se seleccione o active el elemento deseado. 4 Pulse para salir.
Radio Seleccione una emisora almacenada Pulse uno de los botones numéricos (1 a 6). (o) 1 Pulse . 2 Gire la rueda de volumen para seleccionar un número de preajuste y, a continuación, pulse la rueda. Otros ajustes Búsqueda de una emisora 1 Pulse B SRC repetidamente para seleccionar FM o AM. 2 Pulse S / T (o pulse H / I en el mando a distancia) para la búsqueda automática de emisoras.
Radio [SSM] Predeterminado: [XX] [SSM 01–06]/[SSM 07–12]/[SSM 13–18]: Configura automáticamente hasta 18 emisoras para FM. “SSM” deja de destellar cuando se almacenan las primeras 6 emisoras. Seleccione [SSM 07–12]/[SSM 13–18] para almacenar las 12 emisoras siguientes. [IF BAND] [SSM] [SSM 01–06]/[SSM 07–12]/[SSM 13–18]: Configura automáticamente hasta 18 emisoras para FM. “SSM” deja de destellar cuando se almacenan las primeras 6 emisoras.
Radio Código PTY para FM Radio Data System [NEWS], [AFFAIRS], [INFO], [SPORT], [EDUCATE], [DRAMA], [CULTURE], [SCIENCE], [VARIED], [POP M] (música), [ROCK M] (música), [EASY M] (música), [LIGHT M] (música), [CLASSICS], [OTHER M] (música), [WEATHER], [FINANCE], [CHILDREN], [SOCIAL], [RELIGION], [PHONE IN], [TRAVEL], [LEISURE], [JAZZ], [COUNTRY], [NATION M] (música), [OLDIES], [FOLK M] (música), [DOCUMENT] CD/USB/iPod Inserte un disco Expulsa el disco Lado de la etiqueta La fuente cambia automáticamente a
CD/USB/iPod Conecte un iPod/iPhone iPod/ iPhone Terminal de entrada USB Accesorio del iPod/iPhone* y/o KD-T915BTS: También se puede conectar al cable USB desde la parte trasera de la unidad (Terminal de entrada USB). Para En la placa frontal En el mando a distancia Retroceder/avanzar rápidamente Pulse y mantenga pulsado S / T. Pulse y mantenga pulsado H / I. Seleccionar una pista/archivo Pulse S / T. Pulse H / I. Seleccionar una carpeta*1 Pulse 2 J / 1 K. Pulse J / K.
CD/USB/iPod Seleccionar Music drive Pulse 5 MODE repetidamente mientras está en una fuente USB FRONT/ USB REAR/USB. Se reproducirán las canciones almacenadas en la siguiente unidad. • Memoria interna o externa seleccionada de un smartphone (Clase de almacenamiento masivo). • Unidad seleccionada de un dispositivo de múltiples unidades. Seleccionar modo de control Pulse 5 MODE repetidamente mientras está en la fuente iPod FRONT/ iPod REAR/iPod USB (o fuente iPod BT).
AUX Pandora® (excepto para KD-T711BT) La música de un reproductor de audio portátil se puede escuchar a través de una toma de entrada auxiliar. Puede escuchar Pandora en el iPhone/iPod touch (a través de Bluetooth o del terminal de entrada USB) o dispositivo Android (a través de Bluetooth). Preparativos: Seleccione [ON] para [BUILT-IN AUX] en [SOURCE SELECT].
Pandora® (excepto para KD-T711BT) Para En el mando a distancia En la placa frontal Reproducción/pausa Pulse la rueda de volumen. Pulse d. Saltar una pista Pulse T. Pulse I. Seleccione pulgar arriba o pulgar abajo* Pulse 2 J / 1 K. Pulse J / K. Para marcar la información sobre la canción actual Pulse y mantenga pulsada la rueda de volumen. Aparece “BOOKMARKED” y la información se almacena en su dispositivo. • El marcador está disponible en su cuenta de Pandora pero no en esta unidad.
Spotify Puede escuchar Spotify en el iPhone/iPod touch (a través de Bluetooth o del terminal de entrada USB) o dispositivo Android (a través de Bluetooth). Preparativos: • Instale la última versión de la aplicación Spotify en su dispositivo (iPhone/iPod touch o dispositivo Android) y, a continuación, cree una cuenta e inicie sesión en Spotify. • Seleccione [ON] para [SPOTIFY SRC] en [SOURCE SELECT]. (Página 6) Comience a escuchar 1 Inicie la aplicación Spotify en su dispositivo.
Radio SiriusXM® Spotify (para KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS) Buscar una canción o una emisora 1 Pulse . 2 Gire la rueda de volumen para seleccionar un tipo de lista y, a continuación, pulse la rueda. Los tipos de listas visualizados difieren dependiendo de la información enviada por Spotify. 3 Gire la rueda de volumen para para seleccionar la canción o la emisora deseada y, a continuación, pulse la rueda.
Radio SiriusXM® (para KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS) Comience a escuchar 1 Pulse B SRC repetidamente para seleccionar SIRIUS XM. 2 Pulse . El indicador “ ” se enciende. 3 Gire la rueda de volumen para seleccionar CATEGORY y, a continuación, pulse la rueda. 4 Gire la rueda de volumen para seleccionar una categoría en la lista y, a continuación, pulse la rueda. Si se selecciona “ALL CHANNELS”, se mostrarán todos los canales disponibles.
Radio SiriusXM® (para KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS) SmartFavorites y TuneStart™ Los canales presintonizados por el usuario se asignan inicialmente a los canales SmartFavorites. El canal SmartFavorite estará disponible con los sintonizadores SiriusXM modelo SXV200 o posteriores. El sintonizador para vehículos SiriusXM almacena automáticamente el contenido de difusión de audio de los canales SmartFavorites en segundo plano.
Radio SiriusXM® (para KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS) TuneScan™ [CODE SET] 1 2 3 4 Pulse la rueda de volumen para ingresar en [NEW CODE]. Gire la rueda de volumen para seleccionar un número. Pulse S / T para mover la posición de ingreso. Repita los pasos 2 y 3 para ingresar un nuevo código de acceso de 4 dígitos. 5 Pulse la rueda de volumen para confirmar. 6 Repita los pasos 2 a 5 para volver a confirmar el código de acceso.
Uso de otras aplicaciones Aplicación JVC Remote Predeterminado: [XX] La aplicación JVC Remote le permite controlar el receptor para automóvil JVC desde un iPhone/iPod touch (a través de Bluetooth o del terminal de entrada USB) o un dispositivo Android (a través de Bluetooth). • Para obtener más información, visite . [REMOTE APP] [SELECT] Seleccione el dispositivo ([IOS] o [ANDROID]) en el que desea ejecutar la aplicación.
Bluetooth® • Las funciones Bluetooth podrían no funcionar con esta unidad, dependiendo de la versión de Bluetooth, del sistema operativo y de la versión de firmware de su teléfono móvil. • Para realizar las siguientes operaciones, asegúrese de activar la función Bluetooth del dispositivo. • Las condiciones de la señal varían dependiendo del entorno.
Bluetooth® • KD-T711BT/KD-T710BT/KD-TD71BT/KD-SR86BT, el(los) indicador(es) “ “ ” se enciende(n). ” y/o • Esta unidad es compatible con Emparejamiento Simple y Seguro (SSP). • Pueden registrarse (emparejarse) hasta cinco dispositivos en total. • Una vez finalizado el procedimiento, el dispositivo Bluetooth quedará registrado en la unidad aunque la reinicialice. Para borrar el dispositivo emparejado, consulte [DEVICE DELETE] en la página 24.
Bluetooth® Las siguientes operaciones pueden diferir o no estar disponibles dependiendo del teléfono que se haya conectado. Para En la placa frontal En el mando a distancia Mejorar la calidad de voz Primera llamada entrante... Contestar una llamada o la rueda Pulse de volumen. Pulse J / K / H / I. Rechazar una llamada Mantenga pulsado o la rueda de volumen. Pulse y mantenga pulsado J / K / H / I. Mantenga pulsado o la rueda de volumen. Pulse y mantenga pulsado J / K / H / I.
Bluetooth® Predeterminado: [XX] [RECENT CALL] (Solo si el teléfono es compatible con PBAP.) 1 Pulse la rueda de volumen para seleccionar un nombre o un número de teléfono. • “<” indica llamada recibida, “>” indica llamada realizada, “M” indica llamada perdida. • El mensaje “NO HISTORY” aparece si no existe un historial de llamadas o número de llamada registrado. 2 Pulse la rueda de volumen para llamar. [PHONEBOOK] (Solo si el teléfono es compatible con PBAP.
Bluetooth® Predeterminado: [XX] Almacenar un contacto en la memoria Puede guardar hasta 6 contactos en los botones numéricos (1 a 6). [BT MODE] 1 Pulse para ingresar al modo Bluetooth. 2 Gire la rueda de volumen para seleccionar [RECENT CALL], [PHONEBOOK] o [PHONE SELECT] [DIAL NUMBER] y, a continuación, pulse la rueda. 3 Gire la rueda de volumen para seleccionar un contacto o ingrese un número de teléfono.
Bluetooth® Modo de comprobación de compatibilidad Bluetooth Puede comprobar la conectividad del perfil compatible entre el dispositivo Bluetooth y la unidad. • Asegúrese de que no haya ningún dispositivo Bluetooth emparejado. 1 Pulse y mantenga pulsado . Aparece “BLUETOOTH” “CHECK MODE”. “SEARCH NOW USING PHONE” “PIN IS 0000” se desplazan en la pantalla.
Bluetooth® Bluetooth — Audio Para En la placa frontal Repetir reproducción Pulse 4B repetidamente. [TRACK REPEAT], [ALL REPEAT], [GROUP REPEAT]*1, [REPEAT OFF] Mientras está activada la fuente BT AUDIO, es posible conectar a cinco dispositivos de audio Bluetooth y cambiar entre los cinco dispositivos. Reproducción aleatoria Pulse 3 A repetidamente. Seleccionar un archivo de una carpeta/lista Consulte el apartado “Seleccione el archivo que desea reproducir” que aparece en la página 11.
AMAZON ALEXA (excepto para KD-T711BT) Alexa es un servicio de voz basado en la nube desarrollado por Amazon. Puede pedirle a Alexa que reproduzca música, obtenga informes meteorológicos, información sobre el tráfico, controle dispositivos domésticos inteligentes, haga compras en Amazon, realice búsquedas en Internet, crea recordatorios y más. Preparativos: • Cree una cuenta en .
AMAZON ALEXA (excepto para KD-T711BT) Comience a escuchar Cuando Alexa está en estado de inactividad... 1 Para activar Alexa, pulse en la unidad. En la pantalla se muestra: “LISTENING...”. 2 Comuníquese con Alexa a través del micrófono conectado. (Página 20) 3 Puede realizar las siguientes operaciones durante la reproducción de música de la fuente ALEXA: Operaciones básicas Una vez establecida la conexión de Alexa... 1 Pulse en la unidad para hablar con Alexa.
Ajustes de audio Configura sus propios ajustes de sonido para cada fuente. • Los ajustes se guardan en [USER] para [PRESET EQ]. • Los ajustes realizados afectan a los ajustes actuales de [EASY EQ]. [PRO EQ] [62.5HZ] [LEVEL –09] a [LEVEL +09] ([LEVEL 00]): Ajusta el volumen a programarse para cada fuente. (Antes de realizar un ajuste, seleccione la fuente que desea ajustar.) 1 Pulse y mantenga pulsado .
Ajustes de audio [FADER] (No aplicable si se ha seleccionado crossover de 3 vías.) [POSITION R15] a [POSITION F15] ([POSITION 00]): Ajusta el balance de salida de los altavoces delanteros y traseros. [SOUND EFFECT] [SPACE ENHANCE] (No aplicable para la fuente FM/AM.) [SMALL]/[MEDIUM]/[LARGE]: Aumenta virtualmente el espacio acústico. ; [OFF]: Se cancela. [SND RESPONSE] [LEVEL1]/[LEVEL2]/[LEVEL3]: Hace que el sonido sea virtualmente más realista. ; [OFF]: Se cancela.
Ajustes de audio KD-T711BT/KD-T710BT/KD-TD71BT: Ajustes salida altavoz [SPK/PRE OUT] Señal de audio a través de la terminal de salida de línea (Aplicable solo si [X ‘ OVER TYPE ] está ajustado a [2-WAY]) (página 30) Configuración de Seleccione la configuración de salida para los altavoces [SPK/PRE OUT], basándose en el método de conexión del altavoz. [REAR/REAR] Salida de los altavoces traseros [REAR/SUB.
Ajustes de audio Ajustes de crossover A continuación se describen los elementos de ajuste disponibles para crossover de 2 vías y crossover de 3 vías. PRECAUCIÓN Seleccione el tipo de crossover de acuerdo con la conexión de los altavoces. (Página 46, 47) Si selecciona un tipo incorrecto: • Se podrán dañar los altavoces. • El nivel de sonido de salida puede ser extremadamente alto o bajo. SPEAKER SIZE Selecciona, dependiendo del tamaño del altavoz conectado, el rendimiento óptimo.
Ajustes de audio [SUBWOOFER LPF]*2*3 [SW LPF FRQ] [30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/ [90HZ]/[100HZ]/[120HZ]/[150HZ]/[180HZ]/ [220HZ]/[250HZ]/[THROUGH] [SW LPF SLOPE] [–06DB]/[–12DB]/[–18DB]/[–24DB] [SW LPF PHASE] [REVERSE] (180°)/ [NORMAL] (0°) [SW LPF GAIN] [MID RANGE] [HPF FRQ] [30HZ]/[40HZ]/[50HZ]/[60HZ]/[70HZ]/[80HZ]/[90HZ]/ [100HZ]/[120HZ]/[150HZ]/[180HZ]/[220HZ]/[250HZ]/ [THROUGH] [HPF SLOPE] [–06DB]/[–12DB] [LPF FRQ] [–08DB] a [00DB] [1KHZ]/[1.6KHZ]/[2.5KHZ]/[4KHZ]/[5KHZ]/[6.
Ajustes de audio Ajustes de la alineación del tiempo digital Cómo determinar automáticamente el tiempo de retraso [POSITION] Selecciona su posición de escucha (punto de referencia). [ALL]: Sin compensación ; [FRONT RIGHT]: Asiento delantero derecho ; [FRONT LEFT]: Asiento delantero izquierdo ; [FRONT ALL]: Asientos delanteros • [FRONT ALL] se visualiza sólo cuando [X ' OVER TYPE] se ajusta a [2-WAY]. (Página 30) [DISTANCE]*1 [0FT] a [20.01FT]: Ajusta con precisión la distancia a compensar.
Ajustes de visualización Identificación de zonas para los ajustes de brillo 4 Pulse KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS: Para volver al elemento de ajuste anterior, pulse para salir. . Predeterminado: [XX] [DISPLAY] [DIMMER] Oscurece la iluminación. [OFF]: El dimmer está desactivado. El brillo cambia a la configuración [DAY]. [ON]: El dimmer está activado. El brillo cambia a la configuración [NIGHT]. (Consulte a continuación ajustes de “[BRIGHTNESS]”.
Ajustes de visualización [COLOR] (para KD-T915BTS/KD-T910BTS/KD-TD91BTS/KD-T91MBS) [PRESET] [DAY COLOR] [NIGHT COLOR] [COLOR GUIDE] Selecciona por separado los colores de iluminación para los botones en diferentes zonas. 1 Selecciona una zona ([ZONE 1], [ZONE 2], [ALL ZONE]). (Véase la ilustración en la página 35.) 2 Seleccione un color para la zona seleccionada. • [COLOR 01] a [COLOR 49] • [USER]: Se muestra el color que ha creado para [DAY COLOR] o [NIGHT COLOR].
Aprendizaje del mando a distancia del volante de dirección (para KD-T711BT) 6 En el mando a distancia del volante de dirección, pulse y mantenga pulsadas las teclas de control a las cuales desea asignar una función. Aparecerá una lista de funciones de teclas en la pantalla. [NONE] (predeterminado)/[MUTE]/[SEEK UP]/[SEEK DOWN]/[VOL UP]/[VOL DOWN]/ [MODE]/[ON HOOK]/[OFF HOOK]/[VOICE]/[ENTER] 7 Gire la rueda de volumen para seleccionar la función que desea asignar y luego pulse la rueda.
Referencias Archivos reproducibles Acerca de Pandora • Archivos de audio que pueden reproducirse: Para discos: MP3 (.mp3), WMA (.wma), AAC (.aac) Para el dispositivo de clase de almacenamiento masivo USB: MP3 (.mp3), WMA (.wma), AAC (.aac), AAC (.m4a), WAV (.wav), FLAC (.
Referencias Cambiar la información en pantalla Nombre de la fuente Cada vez que pulsa , la información en pantalla cambia. • Si la información no está disponible o no está registrada, aparecerá “NO TEXT”, “NO NAME”, u otra información (por ej., nombre de la emisora) o la pantalla quedará en blanco.
Referencias KD-T711BT/KD-T710BT/KD-TD71BT/KD-SR86BT: Visualización principal Nombre de la fuente Información en pantalla: Principal PANDORA/PANDORA BT Nombre de la emisora Nombre de la emisora con efecto de sincronización de música* Compartida/Radio Título de la canción Artista Título del álbum Tiempo de reproducción Fecha vuelta al comienzo SPOTIFY/SPOTIFY BT Título del contexto Título del contexto con efecto de sincronización de música* Título de la canción Artista Título del álbum Tiempo de reprodu
Localización y solución de problemas Síntoma Radio Síntoma Solución El orden de reproducción no es el que se esperaba. El orden de reproducción se determina por el orden en que se grabaron los archivos (discos) o por el nombre del archivo (USB). El tiempo de reproducción transcurrido no escorrecto. Esto depende del proceso de grabación anterior (disco/USB). Aparece “MISWIRING CHECK WIRING THEN PWR ON”.
Localización y solución de problemas 42 Solución Síntoma Solución Esta unidad está preparando todavía la lista de música del iPod/iPhone. Puede que tarde un poco, inténtelo de nuevo más tarde. “DISCONNECTED” “NO DISC” Inserte un disco reproducible en la ranura de carga. “CONNECTING” “NO DEVICE” Conecte un dispositivo (USB/iPod/iPhone) y cambie de nuevo a la fuente USB/iPod/iPhone. “MEMORY FULL” Ha alcanzado el limite máximo de almacenamiento en su iPod/ iPhone.
Localización y solución de problemas Solución “SUBSCRIPTION UPDATED – PRESS ENTER TO CONTINUE.” Su suscripción ha sido actualizada. Para continuar, pulse la rueda de volumen. “CODE ERROR” Asegúrese de haber ingresado el código de acceso correcto. (Página 18) “NO CONTENT” No existe suficiente contenido para iniciar TuneScan. “SCAN CANCEL” TuneScan ha sido cancelado. No se detecta ningún dispositivo Bluetooth. • Vuelva a buscar el dispositivo Bluetooth. • Reinicialice la unidad.
Localización y solución de problemas AMAZON ALEXA Síntoma Solución Alexa no responde a las entradas de voz. La nube de Amazon no pudo analizar la entrada de voz. Respuesta incorrecta de Alexa. Alexa no me entiende o no capta toda mi petición o frase. Por favor intente de nuevo. (Página 28) “DISCONNECTED” Asegúrese de conectar su smartphone a la unidad a través de Bluetooth. (Página 20) No se puede conectar o volver • Asegúrese de que el dispositivo de audio esté conectado a través de Bluetooth.
Instalación/Conexión Lista de piezas para la instalación (A) Placa frontal (×1) (B) Placa embellecedora (×1) (C) Manguito de montaje (×1) (D) Mazo de conductores (×1) Instalación de la unidad (montaje en el tablero) Prepare el cableado necesario. (Página 46) Gancho en el lado superior Salpicadero del automóvil Antes del montaje, oriente la placa embellecedora tal como se muestra en la ilustración.
Instalación/Conexión Conexión del cableado IMPORTANTE Se recomienda instalar la unidad con un mazo de cables disponible en el mercado que sea adecuado para su automóvil y, para fines de seguridad, deje esta tarea en manos de profesionales. Consulte con un distribuidor de productos de audio para automóviles.
Instalación/Conexión Conecte los componentes externos Conecte los amplificadores externos a través de los terminales de salida Cable de señal (no suministrado) Amplificador de JVC* Terminales de salida Cable remoto (no suministrado) No. Pieza 1 Para KD-T915BTS: Cable USB (5 V CC 1,5 A) (aproximadamente 1 m/3,3 pies) Al cable remoto (azul/blanco) del mazo de conductores.
Especificaciones FM Gama de frecuencias Sensibilidad de silenciamiento (DIN S/N = 46 dB) USB 1.1, USB 2.
Audio Versión Bluetooth V4.2 Voltaje de trabajo Batería de 12V CC para vehículos Gama de frecuencias 2,402 GHz — 2,480 GHz Tamaño de instalación (An × Al × F) Potencia de salida RF (E.I.R.P.
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. • Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.