User Manual

Advanced operations
33
Advanced
operations
English
The VFP (Video Fine Processor) function allows you to
adjust the picture character according to the type of
programming, picture tone or personal preferences.
¶ During playback
1
Press VFP - PROGRESSIVE SCAN.
The VFP mode selection window appears on the TV
screen.
2
Use 2/3 to select the desired preset.
Each time you press the button, the VFP mode
changes as follows.
Set the video type most suitable to the current
program or the room conditions.
"NORMAL" is suitable for watching TV in a general
room. "CINEMA" is suitable for watching a movie
software in a room with suppressed light.
They are factory presets and you cannot change
parameters for them.
While selecting "USER 1" or "USER 2", you can
adjust parameters that affect the picture character
and store the settings as the user preset. See the
next step.
3
To define a user setting, select a parameter to
be edited using 5/∞ from the followings.
• GAMMA
Controls the brightness of a shaded portion
without changing the brightness of the entire
picture.
This control is optimum when you adjust the
pictures of software which generates subdued
black in a bright room.
The setting range is +4 to -4.
• BRIGHTNESS
Controls the brightness of the screen.
The setting range is +16 to -16.
• CONTRAST
Controls the contrast of the screen.
The setting range is +16 to -16.
• SATURATION
Controls the color depth of the screen.
The setting range is +16 to -16.
• TINT
Controls the tint of the screen.
Use the appearance of a natural complexion as
the guideline.
The setting range is +16 to -16.
• SHARPNESS
Controls the sharpness of the screen.
The setting range is +3 to 0.
• Y DELAY
Controls the color gap of the screen.
The setting range is +2 to -2.
4
Press ENTER.
A window for setting parameters appears instead
of the VFP mode selection window.
Selected parameter
5
Adjust the level of the parameter using 5/∞.
The higher value enhances the effect.
6
Press ENTER.
The parameter is set and the VFP mode selection
window appears again.
Repeat steps 3 through 6 if you want to set other
parameters.
To adjust the picture character [VFP]
Available :
Selected preset
NORMAL
CINEMA
USER 1
USER 2
TV2
2
TV1
1
TV3
3
TV5
5
TV4
4
TV6
6
TV8
8
TV7
7
TV9
9
TV0
0
TV-/--
10
MUTING
+10
TV/VIDEO
CANCEL
TITLE/
GROUP
SUBTITLERETURN
VFPAUDIOSUBTITLEREPEAT
ANGLEDIGEST
3D
PHONIC
ZOOM
AMP VOL
PROGRESSSIVE
SCAN
RM-SXV008J
REMOTE CONTROL
OPEN/
CLOSE
TV DVD
NEXTPREVIOUS
SELECT STROBECLEAR
SLOW
- SLOW+
VOL - VOL+
CH
+
CH
-
T
O
P
M
E
N
U
M
E
N
U
O
N
S
C
R
E
E
N
C
H
O
I
C
E
ENTER
STANDBY/ON
TV DVD
5/∞/2/3
VFP -
PROGRESSIVE
SCAN
ENTER
NORMAL
BRIGHTNESS
+ 4
GAMMA
+ 4
+13
CONTRAST
+13
SATURATION
+13
TINT
+ 4
SHARPNESS
+ 2
Y DELAY
+ 5
Parameter
NOTES
• The number of setting steps depends on parameters.
• To dismiss the VFP mode selection window:
Press VFP - PROGRESSIVE SCAN.
• The window for VFP mode selection and parameter
setting disappears if no operation is made for about 10
seconds.
+ 5
SATURATION
4
S500(J).book Page 33 Wednesday, February 13, 2002 9:26 AM