Table of Contents Before You Begin 2 K1-F-S Installation 3 K1-TS-S & K1-A1-S Installation 6 K2-A1-S Installation 11 K1-UC-S (Under-Cabinet Mount) Installation 15 Specifications 19 1 K1 & K2 Series Manual 6.0W X 4 R1.
Before You Begin Do not attempt to install this product if you do not understand the instructions or if there are missing or defective parts. Improper installation may result in property damage or in personal injury. STOP What You Will Need: • Stud Finder • Phillips Screwdriver • Electric Drill • 1/8” Drill Bit • • • 9/16” Wrench (K1-F-S only) 1/2” Wrench (K2-A1-S only) 1/4” Drill Bit (K1-UC-S only) To start installation, go to the section pertaining to your specific model.
K1-F-S Installation Instructions Attach the Screen Plate to the Screen ! Caution: With the screen plate in place, test the screw length to ensure that they do not extend past the screen hole depth and damage the screen. 1. Position the screen plate on the screen as shown. 2. Attach the plate with the original screen screws. If they are not long enough to securely mount the screen, try the included screws. 3 K1 & K2 Series Manual 6.0W X 4 R1.
Attach the Wall Plate to the Wall ! Concrete anchors are not provided. To mount to a brick or concrete wall, purchase concrete anchors to accomodate the provided screws. ! When mounting to a drywall or plaster wall, you should attach the wall plate to a 2X4 or larger wood stud to avoid property damage or personal injury. 1. Locate a stud in the wall where you want to mount the screen. 2. Drill pilot holes with a 1/8” drill bit. 3. Attach the wall plate to a stud using the provided black 2” long screws.
Attach the Screen to the Wall Plate 1. Push the screen plate against the wall plate and then let it slide down into place. 2. Fasten the screw through the screw hole in the bottom of the bracket until it seats against the nut. 5 K1 & K2 Series Manual 6.0W X 4 R1.
K1-TS-S & K1-A1-S Installation Attach the Screen Plate to the Screen ! Caution: With the screen plate in place, test the screw length to ensure that they do not extend past the screen hole depth and damage the screen. 1. Position the screen plate on the screen as shown. 2. Attach the plate with the original screen screws. If they are not long enough to securely mount the screen, try the included screws. 6 K1-TS-S K1 & K2 Series Manual 6.0W X 4 R1.
Attach the Wall Plate to the Wall ! Concrete anchors are not provided. To mount to a brick or concrete wall, purchase concrete anchors to accomodate the provided screws. ! When mounting to a drywall or plaster wall, you should attach the wall plate to a 2X4 or larger wood stud to avoid property damage or personal injury. 1. Locate a stud in the wall where you want to mount the screen. 2. Drill pilot holes with a 1/8” drill bit. 3. Attach the wall plate to a stud using the provided black 2” long screws.
Assemble the Arm (K1-A1-S only) 1. Assemble the arm, and attach it to the wall plate. 8 K1 & K2 Series Manual 6.0W X 4 R1.
Attach the Screen to the Wall Plate Using the included inside hex and outside hex wrenchs, attach the screen to the wall plate. The K1-TS-S is pictured to the right. The K1-A1-S is pictured on the next page. 9 K1 & K2 Series Manual 6.0W X 4 R1.
K1-A1-S Attachment 10 K1 & K2 Series Manual 6.0W X 4 R1.
K2-A1-S Installation Instructions Attach the Screen Plate to the Screen ! Caution: With the screen plate in place, test the screw length to ensure that they do not extend past the screen hole depth and damage the screen. 1. Position the screen plate on the screen as shown. 2. Attach the plate with the original screen screws. If they are not long enough to securely mount the screen, try the included screws. 11 K1 & K2 Series Manual 6.0W X 4 R1.
Attach the Wall Plate to the Wall ! Concrete anchors are not provided. To mount to a brick or concrete wall, purchase concrete anchors to accomodate the provided screws. ! When mounting to a drywall or plaster wall, you should attach the wall plate to a 2X4 or larger wood stud to avoid property damage or personal injury. 1. Locate a stud in the wall where you want to mount the screen. 2. Drill pilot holes with a 1/8” drill bit. 3. Attach the wall plate to a stud using the provided black 2” long screws.
Assemble the Arm 1. Assemble the arm, and attach it to the wall plate. 13 K1 & K2 Series Manual 6.0W X 4 R1.
Attach the Screen to the Arm Using the included inside hex and outside hex wrenchs, attach the screen to the wall plate. 14 K1 & K2 Series Manual 6.0W X 4 R1.
K1-UC-S (Under-Cabinet Mount) Installation Drill the Mounting Holes 1. Remove the contents of your cabinet. 2. Hold the bracket under the cabinet where it will be mounted. 3. Insert a pen or pencil through the mounting holes and make marks where you need to drill. 4. Remove the mount and use a 1/4” drill bit to drill holes up through the cabinet bottom where marked. 15 K1 & K2 Series Manual 6.0W X 4 R1.
Attach the Front Cap Piece 1. Slide the cap piece onto the bracket as shown. 16 K1 & K2 Series Manual 6.0W X 4 R1.
Attach the Mount to the Cabinet 1. Insert four mounting screws down through the holes drilled earlier. 2. Place a spacer on each screw between the cabinet bottom and the top of the mount. 3. Tighten the screws down into the mount holes using the provided hex wrench. 4. Install a nut onto the end of each screw. 17 K1 & K2 Series Manual 6.0W X 4 R1.
Attach the Screen to the Mount ! Caution: With the screen plate in place, test the screw length to ensure that they do not extend past the screen hole depth and damage the screen. 1. Position the screen on the screen plate as shown. 2. Attach the plate with the original screen screws. If they are not long enough to securely mount the screen, try the included screws. 18 K1 & K2 Series Manual 6.0W X 4 R1.
Specifications ! Caution: These mounting brackets are intended for use only with the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in instability and cause injury. Model VESA Support K1-F-S 60, 75 100mm K1-TS-S 60, 75 100mm K1-A1-S 60, 75 100mm K2-A1-S 60, 75 100mm K1-UC-S 60, 75 100mm Tilt Range Ext. from Wall 360 circle 1.75” Max.
K1 & K2 Series Manual 6.0W X 4 R1.
