English User Manual sub8 Subwoofer SUBWOOFER Supporting your digital lifestyle™
Important Safety Instructions ATTENTION The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the apparatus. • • • • • • • • • • • CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE BACK PANEL. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Read these instructions. Keep these instructions. Heed all warnings.
Introduction Thank you for choosing the sub8 powered subwoofer. sub8 was designed to augment the bass performance of your speakers in a stereo setup or in a home theater installation. Adding a subwoofer to your system extends the bass response produced by your existing speakers and improves their midrange clarity. In a home theater application, the subwoofer takes care of reproducing signals from the low frequency effects channel.
What’s In the Box? 4 sub8 Power Cord x3 x1 User Manuals RCA Cable
Front & Rear Panels FRONT PANEL 1 8” Paper Cone Driver 1 Supporting your digital lifestyle™ 5
Front & Rear Panels REAR PANEL 1 Volume Knob 2 Low-Pass Filter Frequency Control 3 Standby Power 4 Phase Switch 5 Line Level Input 6 ON / OFF Switch 7 AC Input Connection (100 V - 240 V) 1 2 4 3 5 6 7 6
Setting up and Connecting your Subwoofer Ensure that the ON/OFF Switch is in the OFF position before connecting any component. To some degree, positioning the subwoofer is less critical because it produces only nondirectional low-frequency sounds. However, best results are obtained if the subwoofer is placed either between the left and right speakers or in the vicinity of either the left channel or right channel speaker.
Setting up and Connecting your Subwoofer Sub Out Sub Out − Volume OFF + Sub Out SUB WOOFER R AUDIO PRE-OUT U L COMPONENT AUDIO L R SURROUND VIDEO SPEAKERS SUB WOOFER R FRONT L CENTER R REAR L R SURROUND L HOME THEATER RECEIVER 8 + AUX INPUT - AMPLIFIER
Audio Troubleshooting Guide Frequently asked questions about Kanto’s sub8 subwoofer. 1. None of the lights on the rear of the 4. Speakers are going into standby • • subwoofer are illuminated. • • • Ensure the power cable is connected to the subwoofer and power outlet. Ensure that the power outlet is providing power. Verify that the power switch on the rear of the subwoofer is in the “On” position. Check the fuse on the rear panel of the subwoofer to ensure it’s intact. while listening to audio. 5.
www.kantoaudio.com N.A: 1-888-848-2643 U.K: +44 800086999 support@kantoliving.
Specifications sub8 SUBWOOFER Woofer Nominal Impedance Sensitivity 2.83V (/1W/1m) 8” Paper Cone Driver 4 Ohm 88 dB Amplifier Type Class D Power Output 125 Watts Input Sensitivity 100 mV Total Harmonic Distortion < 0.3% Frequency Response 35 Hz - 175 Hz Low-Pass Filter 40 Hz - 120 Hz Phase Switch Inputs Input Voltage / Frequency Standby Power Consumption 0º and 180º 1 x RCA L/R Line Level AC 100 V - 240 V 50/60 Hz (auto switching) < 0.
Check out more great products from Kanto! + + + SP32PL SP26PL + + www.kantoaudio.com Kanto Audio @kantoaudio Kanto Living kantoaudio Kanto Living Limited Warranty to Original Purchaser Kanto Living Inc. (Kanto) warrants the equipment it manufactures to be free from defects in material and workmanship for the limited warranty period of 2 years.
