Operating instructions

English 15
4. Wipe up any spilled chain oil with a cloth.
5. Close the chain oil tank cap.
Checking the chain tension
몇 CAUTION
Sharp chain
Incision injuries
Wear protective gloves when working on the chain.
1. Remove the bar scabbard.
Illustration E
2. Carefully pull on the chain.
Illustration F
The distance between the guide rail and the chain
must be 4,0 mm.
3. If necessary, adjust the chain tension (see Chapter
Adjusting the chain tension).
Operation
Basic operation
1. Examine the tree and branches for damage such as
rot.
2. Remove the bar scabbard.
3. Hold the device firmly with both hands.
Working techniques
When pruning, proceed as follows:
 Where possible, maintain a distance of approx. 15
cm between the tree trunk and the cut.
 Cut small branches that are thin and light a single
cut with the bottom edge of the guide rail.
 Heavier branches of larger diameter may break or
splinter during pruning. Therefore, cut in several
steps:
a Make a cut in the underside of the branch with the
top edge of the guide rail. This cut should be
about one third of the branch diameter.
Illustration G
b Make a cut in the top of the branch.
c If another cut is necessary, never continue cutting
in an existing cut but rather start a new cut.
The following should be noted when pruning:
 Do not raise the bar higher than 60 ° from the hori-
zontal.
 Do not exert excessive force on the guide rail.
 Do not stand under the branch being sawn off.
 Make sure that the falling branch does not endanger
the user or spectators nor damage any objects.
 Maintain a safety distance of at least twice the
branch length when pruning.
Ending operation
1. Remove the battery pack from the device (see oper-
ating manual Multi-Tool MT 36 Bp).
2. Clean the device (see Chapter Cleaning the de-
vice).
Disassembling the Multi-Tool
1. Disconnect the accessories from the Multi-Tool (see
Multi-Tool MT 36 Bp operating instructions).
Transport
몇 CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during transporta-
tion.
몇 WARNING
Uncontrolled startup
Incision injuries
With the Multi-Tool assembled, remove the battery pack
from the device before transporting it.
Transport the device only with the bar scabbard fitted.
 Secure the device against slipping and tipping over
when transporting in vehicles.
Storage
Clean the device before storing (see Chapter Cleaning
the device).
몇 CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during storage.
몇 WARNING
Uncontrolled startup
Incision injuries
With the Multi-Tool assembled, remove the battery pack
from the device before storage.
Store the device only with the bar scabbard fitted.
1. Remove the carrying belt.
2. Disassemble the Multi-Tool if necessary (see oper-
ating manual Multi-Tool MT 36 Bp).
3. If the device is to be stored for more than one month,
oil the chain to prevent rust.
4. Store the device in a dry, well ventilated location.
Keep away from corrosive substances such as gar-
den chemicals and defrosting salt. Do not store the
device outdoors.
Care and service
몇 WARNING
Uncontrolled startup
Incision injuries
Remove the battery from the assembled Multi-Tool be-
fore all work on the device.
몇 CAUTION
Sharp chain
Incision injuries
Wear protective gloves when working on the chain.
Cleaning the device
1. Use a brush to clean the chain of cutting residue and
dirt.
Illustration H
2. Clean the shaft with a soft, dry cloth.
Maintenance work
Before every use
The following activities must be carried out before every
use:
 Check the filling level of the chain oil, top up the
chain oil if necessary (see Chapter Filling the chain
oil tank).
 Check the chain tension (see Chapter Checking the
chain tension).
 Check the chain for sufficient sharpness, if neces-
sary, invert the guide rail or replace the chain (see
Chapter Replacing the chain).
 Check the device for damage.
 Check all pins, nuts and screws for tightness.