INSTRUCTION MANUAL STANDING WHEELCHAIR KARMAN HEALTHCARE INC. City of Industry, CA 91748 www.KarmanHealthcare.com **Karman Healthcare Inc.
TABLE OF CONTENTS P.3 XO-101: Parts Explanation Chapter 1. SAFETY TIPS 1-1. Standing 1-2. Wheel locks 1-3. Rear wheels 1-4. Armrests 1-5. Power drive Attachments 1-6. Modifications Chapter 2. UNPACKING AND PREPARING THE STAND UP WHEELCHAIR XO SERIES STAND UP WHEELCHAIR FOR USE 2-1. The original package and accessories. 2-2. Unfolding the stand up wheelchair Chapter 3. ADJUSTMENT 3-1. Adjusting the seat depth 3-2. Adjusting the backrest height 3-3. Adjusting the Footrest height 3-4.
XO Series 1 8 2 3 9 10 4 11 5 12 6 13 14 7 01 Back-rest 08 Arm-rest 02 Chest Strap 09 Side Panel 03 Controller 10 Seat Belt 04 Hand Rim & Rear Wheel 11 Leg Straps 05 Wheel Lock 12 Gas Spring 06 Anti-Tippers 13 Control Box 07 Footrest 14 Heel Strap 2
Chapter 1. SAFETY TIPS 1-1. STANDING Attention： ： ●Before using the standing wheelchair you should be familiar with the operation and the functions of the XO units’ parts. ●When using the standing function, use only in standard household and/or hard even ground conditions. Not use when ground is wet or slippery. ●In case of staircase, the standing wheelchair must be carried by 2 persons on the left and right hand side not in-front and behind.
1-3. REAR WHEEL 1-3.1. QUICK RELEASE AXLES Make sure the wheels axle is all the way through before mounting the XO unit. If the release button is inside the frame, the wheels will release and the user will be in danger. 1-3.2. PNEUMATIC TIRES Check pneumatic tires weekly for proper inflation level, listed on tire sidewall. 1-3-3. CURBS, INCLINES AND RAMPS Always practice with a healthcare professional or attendant. Before attempting to negotiate curbs, inclines or ramps alone.
Chapter 2. UNPACKING AND PREPARING THE STANDING WHEELCHAIR XO SERIES FOR USE 2-1. THE ORIGINAL PACKAGE CONTAINS THE FOLLOWING COMPONENTS. ● ● ● ● ● ● ● Standing wheelchair W/ Heel strap & chest belt Knee Support Charger Pump Oil pot User manual and tool for adjustments Option as ordered 2-2. UNFOLDING THE STANDING WHEELCHAIR, PLEASE PROCEED AS FOLLOWS: ● Remove any transport straps or transport guards. ● Grasp the wheelchair at the backrest and pull backward and push downward up to stop.
Chapter 3. ADJUSTMENT Should you require adjustments and alterations to the mechanism of the wheelchair, or any maintenance work, please contact qualified technicians. 3-1. ADJUSTING THE SEAT DEPTH （1）Pull upward or push forward on the handle controller, let the wheelchair frame rise over the rear wheel. （2）After loosening the screws on both sides the seat depth can be adjusted using the various holes at 1” increments. （Fig-5~7） （3）Retighten the screws on both sides.
3-2. ADJUSTING THE BACKREST HEIGHT （Fig-10~13） （1） Remove the padded backrest. （2） After opening the screws, the backrest height can be adjusted in 2 cm increments. （3） Retighten the screws.
3-3. ADJUSTING THE FOOTREST HEIGHT The height of the footrest is adjustable and should be altered in line with your body proportions to guarantee the best standing position possible. Footrest adjustment should also take account of your choice of seat cushion. （Fig-14~16） 14 15 16 ● After loosening the screws the footrest height can be adjusted using the various holes at ~3/4” increments. ● Retighten the screws.
3-4. ADJUSTING THE FOOTREST ANGLE ● After release the screws the footplate angle can be adjusted using the different hole at 10° incline angle.（Fig-17&18） ● Retighten the screws.（Fig-19） 17 18 19 3-5. ADJUSTING THE WHEEL LOCK Note: Make sure pneumatic tires are properly inflated（ （level listed on tire side wall） ）before adjusting the wheel locks.
● Loosen the socket head cap screw on the top of the clamp. Slide the mounting bar forward or backward and rotate it to the correct angle position. The knurl should be embed into the tire approximately 5/16” when in the locked position.（Fig-20） ● Make sure to retighten the socket head cap screw. 20 3-6. THE KNEE SUPPORT AND SAFETY BELT AND CHEST BELT The most important safety features of the stand-up wheelchairs are the knee support & safety belt and chest belt.
3-6-2. THE SAFETY BELT（Fig-23） ● The safety belt holds the waist in place. ● Make sure that the safety belt is secure on the backrest of Velcro fasteners. ● To release the safety belt. Simply press the red button in the center of the catch. ● To slacken, hold the catch at a right angle to the belt and pull. 23 3-6-3. ADJUSTING THE CHEST BELT（Fig-24~26） ● Make sure that the chest belt is secure on the backrest of Velcro fasteners. ● The chest belt is to hold the upper body (chest) in place.
（3） Retighten the screws of clamp. 27 29 28 FOLDING THE BACKREST ● Release the knobs.
3-8. THE QUICK RELEASE REAR WHEELS ● The quick-release axles, the rear wheels can be easily removed and set back on place（Fig-34） ● Depress the release button in the center of the wheel, then pull outward or re-mount the wheel. ● Having mounted the wheel, push and pull it several times to ensure the quick-release axle has definitely locked in. 34 3-9. THE HEEL STRAP （Fig-35） The purpose of the heel strap is to prevent the legs and/or feet slipping backwards. It is fitted behind the heels or higher.
Chapter4. OPERATING THE STANDING AND SITTING FUNCTIONS 1. First, adjust and fix the knee support to suit position and make sure the two triangular form of knee support lock to the double-head screws of frame. （Fig-36&37） 36 37 2. Fix and lock in the safety belt.（Fig-38） 3. Fix and strap on the chest belt.（Fig-39） 38 39 4. Pull upward on the joystick button of the wheelchair controller to operate the standing up function. 5.
Chapter 5. CONTROL SYSTEM 5-1. BATTERY AND CONTROL BOX CONNECTION The main electrical control system is composed of motor, control box, battery and controller. Connect the power cord of control box to the battery. （Fig-40&41） Battery Capacity Indictor 41 40 5-2. BATTERY CHARGE （Fig-42） 1. First, connect the battery charge cords to the battery DC power socket and make sure the cord is securely connected. 2. Connect the AC power cord to the AC socket.（100~240V） 3.
power indicator color Green Battery Capacity Full power Full power Controller Switch ON Switch OFF Sound of buzzer Sound short 1 times Sound short 1 times （Not using over 30 min） Low power Low power Yellow Red ◎Switch ON ◎ Switch OFF Sound short 1 times Sound short 1 times （Not using over 30 min） Empty power ◎Control mode Sound short continue for control ◎Switch can only Push time downward (Safety mode) Empty power Shut down Sound long 1 time and （Must charge immediately） continuous sound short
wheels should stop turning completely. If the brakes are ineffective, they should be tightened up. ● According to frequency of use, lubricate the joint between one a week and once a month.
