Owners Manual xStream™ Fountain Model 2400SF Contents Important Safety. . . . General Instructions. . . . Cord Gauge Chart. . . . Unit Specs. . . . Parts Included. . . . Assembly. . . . Nozzle Options and Assembly. . . . Installation Instructions. . . . Control Panel Installation. . . . C-25 Timer Control Instructions. . . . Maintenance Recommendations. . . . Warranty Policy. . . . Troubleshooting Tips. . . . Replacement Parts. . . . Customer Repair Form. . . . Registration Information. . .
THANKS We at Kasco Marine, Inc. would like to both thank and congratulate you on your purchase of the xStream fountain. We appreciate you choosing Kasco and for your purchase. Your decision to purchase Kasco’s xStream Fountain will not disappoint you. The fountain will be a great addition to your body of water. It will help improve the water quality by adding much needed oxygen and circulation. It will also enhance the aesthetics of the pond or lake with a beautiful fountain pattern.
from hard water deposits and/or algae. (See Maintenance Recommendations.) It is extremely important that proper and sufficient voltage (120V) is supplied to the Fountain motor. Each 120V Fountain is supplied with a UL and CSA approved C-25 GFI Protected Control Box. The Fountain is to be plugged into the C-25 outlet labeled “UNIT” and the C-25 plugged into a properly grounded receptacle (See C-25 Instructions).
Assembly 1. Make sure you have all the parts needed. If any shortages are found, contact your Kasco representative immediately. 2. Place float on motor housing. The power cord notch on the float should line up with the cord. See diagram below of bottom side of float. The 3 bolt holes in the float should line up with bolt receptacles on unit. power cord notch 3. Use one of the 1/4”-20 x 3-1/4” Phillips Pan Head Screws, one 1/4” split washer, and a 1/4” Flat Washer to secure the float.
7. Make sure the cord is coming out of the notch in the float before attaching the screen to the float. All other nozzle options require the following assembly: 8. Align the screen to the float using the picture to guide you. Attach the screen to the float in 3 places using 1/4” x 1 3/8” bolt, 1/4” lock washer, two 1/4” flat washers, and 1/4” nut. Do not overtighten. 1. Place the flow straightener in the fountain tube making sure it rests securely against the tube and the holes line up.
oring Important: Push in black plugs on the inside of the nozzle only. Plugs on Inside 3. Prepare the nozzle before installing using the nozzle choice chart. Different patterns are created by plugging or removing plugs from the inside holes in the nozzle. After using the chart and nozzle pictures to choose a pattern, push plugs into the holes shown with black circles on the chart. The number of possible patterns are not all shown on the following chart.
Pattern # Height (ft) Width (ft) 4 5 18.5 5 6.5 18.5 6 5 18.5 7 7 17 8 5.
Pattern # Height (ft) Width (ft) 10 5.5 21 11 7 21 12 4.5 21 13 7 21 14 5.5 21 15 7.
Pattern # Height (ft) Width (ft) 16 6 20 17 7.5 23 18 5.5 23 19 8 21 20 5.
Pattern # Height (ft) Width (ft) 22 6.5 13 23 8 25 24 4 25 25 8 25 26 6.5 25 27 8.
Pattern # Height (ft) Width (ft) 28 6.5 13 29 8.5 22 30 5 22 31 8.5 24 32 4 24 33 8.
NOTE: Pattern sizes listed are approximate. Variations in voltage caused by regional electrical differences or voltage drop due to long power cords may result in reduced pattern sizes. by sinking them further below the surface. 4. After the nozzle is prepared, attach it to the flow straightener in 4 places using #6 x 1/2” screws and washers. 5. The unit is now ready to be installed. Installation Instructions Use the ropes to position the Fountain in the desired location in the pond/lake.
into the 120V power supply on the post and ENJOY YOUR NEW KASCO AERATOR! ENTER THE WATER WHEN A UNIT IS IN OPERATION! 4. Test the GFCI with the test button now and every 30 days. TIMER-OPERATION INSTRUCTIONS C-25 Control Box will turn the aerator/fountain ON & OFF with the TIMER. Kasco lights will turn ON with the PHOTO EYE and OFF with TIMER.
Maintenance Recommendations ** Under No Circumstances should anyone enter the water while a fountain is operating. ** ** Please keep the original box for maintenance shipping. ** The following maintenance procedures can be utilized to ensure many years of quality performance from your Kasco Fountain and reduce the need for more costly repair work. PROPER INSTALLATION: Proper installation of Kasco equipment will include a power source with ground fault interruption (GFI).
Warranty Policy Warranty Period: Model: 2400SF - 1 years Kasco® Marine, Inc. warrants this Fountain to be free from defects in material or workmanship (except for the ropes, power cord, and propeller) under normal use and service. The Kasco Marine, Inc. obligation under this warranty is limited to replacing or repairing free of charge any defective part within the warranty period from the date of shipment. Customer shall pay shipping charges for returning the unit to Kasco or an Authorized Repair Center.
Other Repairs: Most failed equipment can be repaired at substantially lower costs than replacement with new. Please ship according to the instructions in the previous section. Again, it is best to call ahead for a Return Authorization Number and/or Repair Form so we know the repair is coming. Kasco Marine does estimates on repairs at the request of the customer.
“My Fountain hums, but will not start. When I spin the prop with a stick, it starts up.” This indicated a problem with the Starting Capacitor. Each Kasco Fountain is equipped with a Starting Capacitor to get the unit going when it is first plugged in. If it is operating, but not spinning and can be started by spinning the prop with a stick, the Starting capacitor needs to be replaced by an Authorized Repair Center.
Replacement Parts 2400SF REPLACEMENT PARTS 14 15 23 19 9 24 8 7 17 13 8 7 6 12 5 3 4 21 11 ITEM PART NO. NUMBER 3 140112 4 361110 5 361115 6 7 8 361500 251300 840537 9 251200 10 241024 11 12 13 14 15 16 17 18 243475 462237 361310 361320 361313 840536 584692 361543 19 820405 20 771033 21 22 23 24 475630 140312 334306 334300 25 990410 26 27 28 29 30 31 18 990275 990280 990281 361540 772007 771034 DESCRIPTION QTY.
800 Deere Rd. Prescott, WI 54021 Phone: 715-262-4488 - Fax: 715-262-4487 www.KascoMarine.com Sales@KascoMarine.com Customer Repair Form * Important Reminders * • All repairs sent in MUST be accompanied by a copy of this completed sheet! • Routine maintenance consists of checking the zinc anode regularly and replacing if necessary, keeping the unit clean, keeping the stainless steel can clean, and having the seals and oil replaced every 3 years depending on use.
Registration Information Please register your fountain online at: www.kascomarine.com Also fill in the information below and keep for your records. Model # (Ex. 2400SF)_______________________________ Serial # (Ex. 2101S241025)______________________________ Purchase Date:_____________________ Purchased From:___________________________________ Registration Date: ___________________________ Kasco Marine, Inc. 800 Deere Rd. Prescott, WI 54021 Phone (715) 262-4488 * Fax (715) 262-4487 www.kascomarine.