MOVING WATER FORWARD, SINCE 1968 J SERIES FOUNTAIN 3400, 4400 Operation & Maintenance Manual 3020379 ANSI/UL 778: 2016 Ed.6+R:22Feb2017 CSA C22.2 #108: 2014 Ed.5 Document number 884180 Document version 2021.2.0 800 Deere Rd. Prescott, WI 54021 | 715.262.4488 | sales@kascomarine.com | kascomarine.
TABLE OF CONTENTS Safety First �������������������������������������������������������������������������������������������������������������������������������2 General Instructions ���������������������������������������������������������������������������������������������������������������3 Unit Specifications & Pattern Size ����������������������������������������������������������������������������������������4 Parts Included ������������������������������������������������������������������������������
Back to Contents SAFETY FIRST IMPORTANT: PLEASE READ THIS MANUAL AND SAVE FOR FUTURE REFERENCE WARNINGS: Moving Machinery Shock Hazard • Please read and follow these important instructions to help ensure your safety and the quality performance of your Kasco equipment. • Use caution when dealing with any electrical and/or moving equipment. • Under NO CIRCUMSTANCE should anyone enter the water with the electrical equipment plugged in and/ or in operation.
Back to Contents GENERAL INSTRUCTIONS Inspect the Shipment Immediately inspect your Kasco fountain shipment for any visible damages. Also cross reference the parts supplied with the Parts Included sheet to check for shortages. Shortages should be reported immediately to your Kasco Marine distributor or representative and damages reported to your carrier and Kasco Marine. Assembly & Installation Please see the proper Assembly and Installation Instructions enclosed in this manual.
Back to Contents UNIT SPECIFICATIONS & PATTERN SIZE Model Voltage Operating Amps Locked Rotor Amps Control Panel Connection Unit Connection Single-Phase Units 3400JF 110-120 7.3 18 C-25 plug in Plug into C-25 3400HJF 208-240 3.7 9 Hardwire C-85 Plug into or hardwire C-85 4400JF 110-120 11 40 C-25 plug in Plug into C-25 4400HJF 208-240 5.5 20 Hardwire C-85 Plug into or hardwire C-85 Cord Gauge 3400JF 3400HJF / 4400HJF 4400JF 50 ft. 100 ft. 150 ft. 200 ft. 250 - 400 ft.
Back to Contents PARTS INCLUDED ID Description Qty Part # 1 Fountain 1 N/A 2 Float 1 242001 3 1/4-20 x 4” Phillips Pan Head Screw 4 251220 4 1/4” split washers 7 840537 5 1/4” (3/4” OD) Flat Washer 10 251300 6 1/4 -20 x 1-3/4” Hex Head Bolt 3 475630 7 Bottom Screen Section 3 361540 8 1/4”-20 Nut 3 840536 9 #8 nut 6 771034 10 #8 flat washer 12 361543 11 #8 lock washer 6 771033 12 #8 x 3/4” screw 6 361545 13 Mooring ropes (not pictured) 2 990700 14 Cab
Back to Contents ASSEMBLY INSTRUCTIONS 3 1. Rest the float on the 4 legs of the housing 4 5 Align power cord with notch 3. Turn over. Bring bottom screen sections together. Align bolt holes with legs. 2. Lock washer goes between bolt and flat washer. Tighten down in 4 places. 10 9 10 11 12 4. Tighten down in 6 places to hold the screen together. 5. Secure the bottom screen to the float in 3 places. 8 4 5 5 Make sure cord is sticking out of notch.
Back to Contents ASSEMBLY INSTRUCTIONS (CONT.) 6. Turn upright. Secure power cord to rope hole. Cord Strain Relief Providing strain relief on the cord helps ensure that its weight and any strain placed on it in the water will not cause the float to tilt or cause damage to the unit. If your Kasco cord comes with a strain relief kit attached, attach the available link to the float-side knot in the mooring rope, as pictured here. 7. Choose Nozzle.
Back to Contents INCLUDED NOZZLES 2 1 3 ID Pattern Description 1 Sequoia Narrow geyser, marked S. (Pre-installed) 2 Linden Center geyser with lower conical pattern, 2-piece assembly with bolt. 3 Birch Wide geyser, marked B. 4 Cypress 1 tier of 12 arcing streams, marked C. 5 Willow Wide arc, no nozzle installed. Sequoia Linden Birch 4 Model Height Width 3400 13’ 8’ 4400 18’ 11’ 3400 9’ 29’ 4400 12’ 31’ 3400 7’ 5’ 4400 11’ 8’ 3400 7’ 17’ 4400 9’ 28’ 3400 6.
Back to Contents UNIT INSTALLATION INSTRUCTIONS Use ropes to position the fountain in the desired location in the pond or lake. Anchor the ropes or secure them to the shoreline so that they are free of slack, but not tight. To prevent twisting of the unit due to motor torque, place the anchor at least 3 feet from the float for each foot of depth (Ex. a 6 ft. deep pond would require an anchor 18 ft.. horizontally from the float).
Back to Contents REPLACEMENT PARTS 19 18 17 16 15 14 13 12 11 10 ID Description Qty Part # 1 Anode assembly 1 243475 2 Debris flinger, .500 dia.
Back to Contents MAINTENANCE RECOMMENDATIONS The following maintenance procedures can be utilized to ensure many years of quality performance from your Kasco equipment and reduce the need for more costly repair work. PROPER INSTALLATION: Proper installation of Kasco equipment will include a power source with ground fault protection. The control panel included with the equipment has built-in ground fault protection for both the fountain and the lighting kit.
Back to Contents TROUBLESHOOTING TIPS The following is provided to help diagnose a probable source of trouble. It is a guideline only and may not show all causes for all problems. For additional troubleshooting help, contact your local distributor or visit kascomarine.com for additional guidance. Note: you may need to refer to your owner’s manual that was provided with your control panel for additional control panel settings and adjustments. “My pattern is crooked or does not look even.
Back to Contents WARRANTY Warranty period: 3400JF, 3400HJF, 4400JF, 4400HJF = 2 years Kasco® Marine, Inc. warrants this fountain to be free from defects in material or workmanship under normal use and service (excluding ropes, power cord, and propeller). The Kasco Marine, Inc. obligation under this warranty is limited to replacing or repairing free of charge any defective part within the warranty period from the date of shipment.
Back to Contents NON-WARRANTY REPAIRS Most failed equipment can be repaired at substantially lower costs than replacement with new. If your aerator requires repair and is no longer covered under warranty, please contact Kasco Marine or your local distributor for available options. Please ship according to the instructions on the previous provided. Kasco Marine does estimates on repairs at the request of the customer.
Back to Contents REPAIR CONTACT FORM • Kasco requires that all equipment sent for repair MUST be accompanied by this form and marked to Repairs attention. • • Unit should be cleaned before shipping. • It is the responsibility of the customer to ship and pay freight to Kasco. Kasco Marine 800 Deere Road Kasco is NOT responsible for shipping damage accrued in return shipment.
