MODEL # 842071 COMPONENT # 692665 2000 PSI ELECTRIC PRESSURE WASHER with Hose Reel INSTRUCTION MANUAL THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION, MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
TABLE OF CONTENTS CONGRATULATIONS! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 GENERAL SAFETY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS . . . . . . .
INTRODUCTION This instruction manual is intended for your benefit. Please read and follow the safety, installation, maintenance and troubleshooting steps described within to ensure your safety and satisfaction. The contents of this instruction manual are based upon the latest product information available at the time of publication. The manufacturer reserves the right to make product changes at any time without notice. GENERAL SAFETY READ AND FOLLOW ALL INSTRUCTIONS.
CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage. NOTE provides additional information that is useful for proper use and maintenance of this tool. If a NOTE is indicated, make sure it is fully understood. In addition to SAFETY ALERTS listed above, there could also be numerous symbols alerting the operator that specific safety measures are required to safely operate this tool.
IMPORTANT INFORMATION ABOUT THIS MANUAL Improper and unsafe use of this Pressure Washer can result in death, fire and/or bodily injury. This instruction manual contains important information about product safety. Keep the instruction manual available for others to read before they use the Pressure Washer. Improper maintenance and operation are responsible for the majority of accidents involving Pressure Washers.
SAFETY WARNINGS READ ALL SAFETY WARNINGS BEFORE USING PRESSURE WASHER. GENERAL SAFETY RULES People with electronic devices, such as pacemakers, should consult their physician(s) before using this product. Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker. WARNING: This product can expose you to chemicals including phthalates which are known to the State of California to cause cancer and birth defects or other reproductive harm.
Always make sure the tool is in the OFF position when making adjustments, changing parts, or performing any maintenance. Service must be performed only by qualified repair personnel. Service or maintenance by unqualified personnel may result in a risk of injury. Do not use the tool if the power switch does not turn it “ON” or “OFF”. A tool that cannot be controlled with the switch is dangerous and must be repaired. Store all maintenance tools away from the immediate area before turning ON the tool.
NEVER place hands in front of nozzle. NEVER attempt to attach or remove spray wand or hose fittings while Pressure Washer system is pressurized. DO NOT treat fluid injection injuries as a simple cut. Seek immediate medical attention. HIGH VELOCITY fluid spray can cause objects to break, propelling particles at high speeds. ALWAYS wear approved safety glasses when using or doing maintenance on Pressure Washers. ALWAYS wear protective clothing to prevent accidental spraying.
NEVER cut or splice the power cord or extension cords. DO NOT spray electrical apparatus and wiring. WEAR rubber-soled tennis shoes or other footwear that provides some insulation when operating the Pressure Washer. COLD water use only. FOR EITHER INDOOR OR OUTDOOR USE. Store indoors. DO NOT direct spray toward electrical outlets, switches or products connected to electrical service.
RISK OF ELECTROCUTION: Connect only to properly grounded outlet. Do not remove ground pin. Inspect cord before using. DO NOT use if the cord is damaged. Keep all connections dry and off the ground. DO NOT touch plug with wet hands. Connect to individual branch circuit only. This product is provided with Ground Fault Circuit Interrupter built into the power cord plug. If replacement of the plug or cord is needed, use only identical replacement parts.
FUNCTIONAL DESCRIPTION Unit is Shown After User Assembly FRONT VIEW PRESSURE WASHER FEATURES: 1. Gun 2. Trigger Safety Lock 3. Trigger 4. Wand 5. Nozzle Connector 6. Gun Inlet Connector 7. Handle 8. Gun Holder (Top) 9. Gun Holder (Bottom) 10. Spray Nozzles (4 pcs.) 11. On/Off Switch 12. Handle Lock Detent Pin 13. Folding Hose Reel Handle BACK VIEW 14. Wheel Assembly 15. Detergent Tank 16. Water Inlet/Garden Hose Connector 17. High Pressure Water Outlet 18. Power Cord Hook 19. GFCI Power Cord 20.
ASSEMBLY & SETUP This Pressure Washer requires some assembly. If you have any problems with the assembly of your Pressure Washer, please call the Pressure Washer helpline at 1-800-590-3723. If calling for assistance, please have the model, revision, and serial number from the data tag available. 1. Using a box cutter, cut open the Pressure Washer carton on top. 2. Carefully remove all items from the box and inspect for completeness (see Functional Description). HANDLE/WASHER CONNECTION 1.
1. Before connecting the garden hose to the 2 3 Pressure Washer, connect the garden hose to the water source and run water through the hose to flush out any debris. Shut off the water at the source. 2. Attach garden hose to the Pressure Washer coupling inlet at the lower back of the unit. Ensure that the threads are aligned properly and that the connection is secure. Securely tighten the nut by hand. 3. Turn on the water source. 4.
1. For your protection, wear protective safety glasses. 2. Place the Pressure Washer near the working surface. Make sure that the water source is turned on and all connections to the Pressure Washer and Spray Gun are secure and without any water leakage. For maximum performance and pressure, completely unroll the pressure hose from its storage reel. 3. Carefully remove the gun from its holder. 4. Select the Right Nozzle for the Job.
Fan Pattern Rotation – Turn the cone section of the gun to change the orientation of the fan pattern. ATTACHING NOZZLES TO SPRAY WAND Never place hands in front of nozzle. Never grasp hose or fittings during Pressure Washer operation. Never attempt to attach or remove spray wand or hose fittings while Pressure Washer system is pressurized. Turn off Pressure Washer and lock the Gun Trigger before attempting to change pressure nozzles. 1.
SHUTTING DOWN THE PRESSURE WASHER The Pressure Washer motor runs only when the trigger is engaged. To shut off the Pressure Washer: 1. Release spray gun trigger. 2. Move unit’s ON/OFF switch to OFF position. IMPORTANT: Releasing the trigger will shut off the motor but does not shut off electrical power to the unit. 3. Remove and store quick change pressure washer tip. 4. Turn off water supply. 5.
USE OF CLEANING DETERGENTS TO APPLY DETERGENT: 1. Select a detergent/cleanser appropriate for the intended application. 2. Prepare detergent solution as recommended by the manufacturer. 3. Remove the detergent tank lid. 4. Fill tank with prepared detergent solution. A small funnel may help with this task. Replace the detergent tank lid. 5. Select “Black” detergent dispensing quick change nozzle. used. Detergent will NOT flow unless “Black” detergent nozzle is 6.
• If you have the nozzle too far away from the surface being washed, the cleaning will not be as effective. IMPORTANT: DO NOT get closer than 15 cm (6 inches) when cleaning. MAINTENANCE Regular maintenance will improve performance and extend life of Pressure Washer. Some adjustments will need to be made periodically to properly maintain the Pressure Washer. All service and adjustments should be made at least one time each season. It is important that the maintenance chart below be followed.
NOZZLE The nozzles should be lubricated with non-water soluble grease or light oil regularly. Clogging of the nozzles causes the pump pressure to build up too high and cleaning is required. 1. Make sure Pressure Washer On/Off switch is set to Off and spray gun trigger is locked. 2. Clear blockage in nozzle by inserting the nozzle cleaning needle (provided) through centre hole. 3. After cleaning, remove the needle from nozzle and store for future use.
TROUBLESHOOTING GUIDE Problem Probable Cause 1. Unit is not turned on. 2. Loose or disconnected plug. 3. GFCI has tripped. 4. Thermal switch has tripped. 5. No AC power at the outlet. 6. Main voltage supply is too low. 7. Extension cord is too long or wire size too small. 8. Defective ON/OFF switch. 9. Defective GFCI plug. Unit will not start (when trigger is depressed) 10. Defective gun. Solution 1. Press ON/OFF switch into ON position. 2. Reconnect plug. 3. Push reset button on plug. 4.
TROUBLESHOOTING GUIDE Problem Probable Cause 1. Circuit (outlet) overloaded. AC outlet circuit breaker trips Motor stops suddenly Unit will not stop when trigger is released Unit begins to smoke Trigger will not move 2. Extension cord is too long or wire size too small. Solution 1. Make sure circuit is rated at 15 amps or greater and unit is plugged into a dedicated circuit. 3. Nozzle partially blocked causing excessive pressure. 2. Use proper extension cord (see instructions). 1.
TROUBLESHOOTING GUIDE Problem Gun/hose - Leaking water Pump is noisy Probable Cause 1. Loose fitting. 1. Pump is sucking air. 1. Clogged nozzle. 2. Wand is attached incorrectly. 3. Clogged filter. 4. Kink in the garden hose or hose is wrapped on a storage wheel. 5. Gun/hose assembly is defective. No water coming out of wand 21 Solution 1. Tighten fittings. If persists, Gun/Hose will need to be replaced. Call Customer Service: 1-800-590-3723. 1. Make sure hoses and fittings are air tight.
TROUBLESHOOTING GUIDE Problem Probable Cause Solution 1. Diameter of garden hose is too small. 1. Replace with a 5/8 in. (1.5 cm) or larger garden hose. 2. Water supply is restricted. 2. Make sure garden hose has no kinks, leaks and blockage. 3. Not enough inlet water supply. 3. Open water source fully. 4. Garden hose length is too long. 6. Water inlet filter is clogged. 4. Shorten the length of the garden hose. We recommend a maximum length of 25 to 50 ft. (7.
TROUBLESHOOTING GUIDE Problem Probable Cause Solution 1. Black” detergent nozzle is 1. Use “black” detergent not being used nozzle. No detergent Detergent leak from inside the unit or won’t hold detergent Leaking oil from pump 2. Detergent is too thick. 2. Dilute detergent. 3. Damaged or clogged detergent suction tube. 3. Call Customer Service: 1-800-590-3723. 4. Nozzle is clogged with debris. 4. Unclog nozzle using provided cleaning needle. 1.
SPECIFICATIONS MAX PRESSURE 2000 PSI MAX FLOW RATE 1.4 GPM VOLTAGE RATED INPUT 120V DETERGENT TANK CAPACITY 50.7 FL.OZ. ELECTRICAL CORD LENGTH 35 FT. PRESSURE HOSE LENGTH 25 FT. INLET WATER PRESSURE 40-60 PSI 60HZ, 13A *Meets PWMA-PW101 test requirement.
the applicable warranty period, with a written request by purchaser that Alltrade repair and/or replace the nonconforming item and/or part. We recommend that you keep the original product packaging in the event you need to ship the unit. We suggest the package be insured against loss or in transit damage. When sending your product include your name, address, phone number, dated proof of purchase (or copy), and a statement about the nature of problem.
OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES.
3021528 Conforms to Std. UL 1776 Certified to CAN/CSA-C22.2 STD No.68 KAWASAKI IS A TRADEMARK LICENSED BY KAWASAKI MOTORS CORP., U.S.A., WHICH DOES NOT MANUFACTURE OR DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE DIRECTED TO: FOR WARRANTY / SERVICE 1-800-590-3723 Printed in China Distribution & Returns ©2018, Alltrade Tools, LLC Reno, NV 89508 www.alltradetools.
