Installation instructions Instrucciones de instalaci6n instructions d'installation Engllsh / Espa_ol / Fran_als I en more Elite _/_iC_H e @ F P/N W10747788A Sears Brands Management Corporation Hoffman Estates, IL 60179 U,S,A, www.kenmore.
TABLEOF CONTENTS DISHWASHER SAFETY ............................................................. 2 Make Power Cord Connection .......................................................13 iNSTALLATiON REQUIREMENTS ............................................. 3 Tools and Parts ...................................................................................3 Determine Cabinet Opening ..........................................................15 Install Door Handle ..........................................
iNSTALLATiON REQUIREMENTS Other Parts Needed: (not provided) I Gather the recommended took and parts before starting installation. Read and follow the instructions provided with any took listed here. All Installations Tools Needed: i %" Compression x 3/4 Hose Fitting with rubber seal and 90 ° elbow (required to properly connect household water line to the dishwasher) F,at:b,ade Approved I screwdriver e s _6 " and iV4" /_) 5 parts.
NOTE: If using a flexible braided hose, replace inlet hose after 5 years to reduce the risk of hose failure. Record hose installation or replacement dates on the hose for future reference. For DirectWire For Power Cord I Cabinet Grommet For 11/2"(3.8 cm) hoHe in cabinet, O Number 302797) NOTE: Required for metal cabinets. Power Cord Kit Kit typically incHudes power cord, metallic strain relief, grommet, and twist-on wire Connectors.
A. Insulation may be compressed (not used on all models). B. For panel-ready models, dishwasher depth is 24" (60 cm) not including the 3/4"(1.9 cm) custom door panel. C. Door handles may protrude forward of the face of the dishwasher; varies by model. 3/41 / (1.9 cm) A _4 J 31/2" -41/4'' (8.8 cm - 10.6 cm) / For 4" (10 cm) toe kick. height of cabinet opening is 341/2'' (86.3 cm). Check that all surfaces have no protrusions that would prohibit dishwasher installation.
[] A new drain hose is supplied with your dishwasher. If drain hose is not long enough, use a new drain hose with a maximum length of 12 ft (3.7 m) that meets all current AHAM!IAPMO test standards, is resistant to heat and detergent, and fits the 1" (2.5 cm) drain connector of the dishwasher. See the "Tools and Parts" section at the front of Be sure that the electrical Make sure to connect drain hose to waste tee or disposer inlet above drain trap in house plumbing and 20" (50.
iNSTALLATiON iNSTRUCTiONS Electrical Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher. Failure to do so can result in death or electrical shock. Cable i Discoaaect electric al POwe[ atthe fuse bO× or c!rcu!t J When removing a previous dishwasher, be sure to avoid damaging the existing power cord, drain line, and water line connected to the dishwasher.
Option A_ Power Cord = Option NOTE." A grounded 3 prong outlet is required inside a cabinet next to the dishwasher cabinet opening. B_Direct Wire Helpful Tip." Wiring the dishwasher will be easier if you route the cable into the cab}net opening from the right-hand s}de. Drill a 11/2"(3.8 cm) hole in right-hand See the "Product and Cabinet Opening Drill a 11/2" (3.8 cm) "Product and Cabinet hole in cabinet Opening cabinet side or rear. Dimensions" section. side or rear.
ili"_'i_'_i_J!!D_!iii_iiiii_,,_i:ii_'_!!? _:::_!ii_iiii"'ii_'ii:_I iiii_ii:,i,'ii_,_i,,,_i_!_'_i,_!? '_i_'!_,_J_i,':i:_'iiii_!!ii_,_ '_iiii!,,,,_iii_iiii_"i_,_ii!_? Helpful Tip: Routing the water line through the left-hand cabinet opening will make water connection easier. side of Attach the water supply line (copper tubing or flexible braided line) to the hot water line using a connection configuration that is in compliance with local codes and ordinances.
Connect drain hose to waste tee or waste disposer using one of the following options: - Option * Option * Option , Option Route waterlineandtapeit tothefloorinareashown. Thiswill keepitfrommoving whendishwasher ismoved intocabinet opening. IMPORTANT =Alwaysusea newdrainhose. Check localcodes todetermine whether anairgapisrequired.
Option B_No Waste Disposer- No Air Gap ]. Using a hammer and screwdriver, knock p}ug into disposer. 2. Use needle-nose pliers to remove plug. 3. Connect rubber end of drain hose to air gap and cut if needed. NOTE: Do not cut ribbed section. ]o Fit rubber end of drain hose to waste tee and cut if needed. Attach drain hose to air gap with large drain hose clamp (provided). Use p}iers to squeeze clamp open and move into position. If the drain hose was cut, use a 11/2"to 2" (3.
Iiii iii :ii : iii3 i!iiii : iiiii, :i il :iii! iii!!!i!ii, i:: iiii Moisture barrier Remove and discard the foam blocks (if blocks are present, not all models have them) located above the front legs on each side of the dishwasher. The blocks cover the rope/link pulleys on the dishwasher. J See the "Tools and Parts" section at the front of the guide for part details and orders. 1. Make sure the area under the cabinet is clean and dry for installation of the moisture barrier. 2.
Option A_ Remove Access Panel - Plastic Panel Option A_ Power Cord Using a f}at-bJade screwdriver, turn the plastic fasteners 1/4 turn counterclockwise to unlock them. Remove panel. Do not remove tech sheet from access panel.
Power CordmConnect remaining wires Route cord so that it does not touch dishwasher motor or lower part of dishwasher tub. Pull cord through strain relief in terminal box. Note= A maximum of two power cord supply conductors (12 AWG largest size) plus one grounding conductor are permitted in the terminal box Select UL Usted!CSA Approved proper size. See the "Tools and guide for part details.
Dishwasher Height Adjustment Cha Cabinet opening height Front legs height Wheel position Insulation blanket 331/2'' (85.1 mm) 3/8,, (9.8 mm) Removed Cut 34" (86.4 cm) 341/4'' (87.0 cm) 34W' (87.6 cm) %" (22 mm) 1" (25 mm) ! 1/8" (28.8 mm) 1 No cut 2 No cut 3 No cut Place wires inside terminal box. Replace the cover by inserting the hooks of the terminal cover into the slots in the floor of the terminal box and sliding the cover tight against the back walE where wires come in.
Adjust wheels and legs Mounting stud Handle Setscrew (in bottom of handle) Hex key Turn both required Adjustment leveler position legs to the same height. determined from Put wheels "Dishwasher in the Height Chart." IMPORTANT= Do not scratch the front panel during this procedure. Remove the door handle and hardware bag containing the setscrews and hex key from the cardboard box. Setscrews are already installed in the handle. Place handle on mounting studs with the setscrews facing down.
iMPORTANT: The dishwasher must be secured to the cabinet as one of the final steps. Prepare the dishwasher for this by attaching the two brackets found in the parts bag to the With another person holding the rear of the dishwasher to keep it from tipping, open dishwasher door and place towel over pump assembly and spray arm of dishwasher. This will keep screws from falling into pump area when you are securing dishwasher to cabinet. dishwasher.
iMPORTANT: Double-check correct placement of utilities. Grasp the sides of the dishwasher at the edges of the door panel. Tilt dishwasher backward on wheels and move dishwasher close to JAdd 90 ° elbow fitting water supply line to the cabinet opening. i Get 3/8" compression See the "Tools part details and the 90 ° elbow x 3/_" hose fitting and Parts" orders. section Connect to the water opening. facing as shown above. Copper upward, tubing only: Attach the nut and ferrule elbow threads.
To adjust the door spring tension, unhook the spring from the rear leg of dishwasher. Using a 5A6" nut driver or hex socket, remove the screw from the tensioner. The screw can be put into one of 3 holes (1, 2, 3) in the front leg of dishwasher. If the door closes by itself, move the tensioner to a lower-numbered hole and replace screw. Reattach door spring to rear leg. NOTE: Tensioners on both sides of dishwasher should be secured at same holes.
C)_:I iiii_i!_iii!!ii,i:i;l _¸i!o _j_iiJ_iiiiil_i!i!!i_ ¸i_ii%i_i:;_ii_;;;!_ii_!iS ,¸ Check that leveling legs are firmly against the floor. Close and latch the door, and place level against the front panel. Check that dishwasher is centered from front to back in the opening. If needed, adjust leveling leg until dishwasher is plumb. Repeat for other side of dishwasher. Helpful Tip: Push up on front of dishwasher to raise dishwasher off the ground to adjust front legs.
Place the small drain hose clamp onto the small end of the drain hose. Push the new drain hose into the rubber drain hose connector up to the drain hose stop. Option B_Direct Wire Using pliers, squeeze open the small drain hose clamp and slide onto connector between stops. Install a UL Listed!CSA Approved metallic strain relief. See the "Tools and Parts" section at the front of the guide for part details and orders.
Electrical Shock Hazard Electrically ground dishwasher. Connect ground wire to green ground connector terminal box. in in strain Do not use an extension cord. relief | Failure to follow these instructions can result in death, fire, or electrical shock. Ground Tighten strain relief screws to secure cable. Make sure screw heads are facing up when tightening conduit nut. Ground ) Form bare ground wire into a U-shaped hook.
Option 2 = Side Mount Dishwasher To Cabinet. Locate brackets installed on sides of dishwasher (during Choose Attachment Method). Check that dishwasher is still level front-to-back [] Drill pilot holes in cabinet to avoid splitting the wood. [] Secure dishwasher to cabinet with two, #10 x Y_" Phillipshead screws (included). and side-to= side in cabinet opening. Open door and check that space between dishwasher cabinet opening and tub is equal on both sides.
If securing with a side attachment, check that sides of door do not rub against the screw heads. If they do, dishwasher must be re-centered. When dishwasher is properly centered, replace plastic buttons. Using a flat-blade screwdriver, turn the fasteners 1/4 turn clockwise to lock into place. The fasteners slot will be straight up and down when properly locked. Option B, Install Access Panel - Meta_ Pane_ Check that power supply wire or cord does not touch dishwasher motor or lower part of dishwasher tub.
Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions fire_ or electrical shock. can result in death_ Hold the 2 panels together and place them against dishwasher leg. Using a Phillips screwdriver or 1/4" nut driver, reinstall the screws through the holes in the access panel, and the slots in the lower panel. Check that the lower edge of the lower panel contacts the floor.
':(iii iiise c iiiii,,_: O,p e _'oiiiiilili ¸¸iili _c_, iiii'_"_,_J_ [] Read the Dishwasher User Guide that came with your dishwasher. [] Check that all parts have been installed and no steps were skipped. Check that you have all tools used. [] Start dishwasher and allow it to complete the shortest wash cycle. After the first 2 minutes, unlatch door, wait 5 seconds, then open door. Check that there is water in the bottom of the dishwasher tub. Check that dishwasher is working properly.
