Installation Built-In Instructions Dishwasher If you have questions, call 1-800-4-MY-HOME®(US) www. Sears.com eS BEFORE YOU BEGIN Read these instructions completely and - Observe Note to allow for future removal from the enclosure if service is required. all governing codes and If you received a damaged dishwasher, you should immediately contact your dealer or builder. sure these available ordinances. ° or IMPORTANT - The dishwasher MUST be installed to carefully.
Installation Preparation PARTS SUPPLIED: uoFe Two #8 Phillips flat head wood screws, 5/8” long to secure dishwasher to underside of countertop (in literature package). Two Phillips head, color matched toekick screws (in literature 2 Wood Screws package).
Installation Preparation PREPARE DISHWASHER ENCLOSURE * The dishwasher must be installed so that drain hose is no more than 10 feet in length for proper drainage. * The dishwasher back, and CLEARANCES: 32.5" installed into must be fully enclosed must not support any on the top, sides and part of the enclosure. When Countertop a corner, allow 2” min. clearance Underside of Countertop to Floor dishwasher adjacent cabinet, wall or and other appliances. Allow Cabinets 25-5/8" min.
Installation Preparation PREPARE ELECTRICAL WIRING WARNING bd tf FOR PERSONAL SAFETY: Remove house fuse or open circuit breaker before beginning installation. Do not use an extension cord or adapter Electrical 1-1/2" Dia. plug with this appliance. Hole (Max.) Requirements * This appliance must be supplied with 120V, 60 Hz., and connected to an individual properly grounded branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay 24" from Wall fuse.
Installation Instructions PREPARE HOT * enter The line may WATER from BEFORE YOU LINE either side, rear or floor within Locate and shaded area shown in Figure F. * The line may pass through the same lf power the water cord with plug hole as the electrical 2 additional literature line. is used, water set aside the package 2 Phillips head cable and drain hose. Or, cut an additional 1-1/2” dia.
Installation Instructions STEP 2 | ADJUST * Move LEVELING LEGS the dishwasher close to the installation location and STEP 4 | INSTALL 90° ELBOW « Wrap 90° elbow with thread seal tape. * Install a 90° elbow onto the water valve. lay it on its back. Adjust to Installation Height C Figure H + Measure leveling installation height and dishwasher height. Extend legs out from the dishwasher base, 1/4" Figure L less than installation height. TOEKICK * Remove the 4 toekick screws.
Installation Instructions STEP 5 * POSITION WATER LINE AND HOUSE WIRING Position water supply line and the opening to avoid and components STEP 7 house wiring on the floor of interference with base of dishwasher under dishwasher. [SLIDE DISHWASHER PARTIALLY INTO CABINET DO NOT PUSH AGAINST FRONT KNEES. DAMAGE WILL OCCUR. * Slide dishwasher * As you proceed, into the opening a few PANEL WITH inches at a time.
Installation Instructions STEP 8 | POSITION * DISHWASHER UNDER COUNTERTOP Reposition Dishwasher by Grasping Both Sides With Hands Check to be sure that wires are secure under the dishwasher and not pinched or in contact with door springs or other dishwasher components. TIP: Check tub insulation blanket, if equipped. It should be positioned so it is not bunched springs. Check * by opening Push dishwasher and up or interfering with door closing the door. into cabinet.
Installation Instructions STEP 10 SECURE DISHWASHER TO COUNTERTOP OR CABINET In this step you will need aside prior to Step 1. countertop of wood, other the 2 Phillips special The dishwasher or the cabinet sides. use Method materials 1. When that will not head screws set must be secured When STEP 11 countertops to the are made countertops are granite or accept screws, use Method |CONNECT SUPPLY WATER Connect water supply to 90° elbow.
Installation Instructions STEP 12 FOLLOW |CONNECT ALL LOCAL CODES DRAIN AND LINE DRAIN ORDINANCES. * marked Method on the air gap, waste tee or disposer. Cut on the line as required for your drain INSTALLATION line to air gap, waste tee or disposer using either previously determined The drain hose molded end will fit 5/8”, 3/4” or 1” diameter connections Connect LINE method. 1 - Air gap with waste tee or disposer aa installation.
Installation Instructions STEP 13 |CONNECT SUPPLY POWER STEP 14 Review this list after installing your dishwasher to avoid charges for a service call that is not covered by your warranty. Skip this step if equipped with power cord. Verify that power is turned off at the source. Check to be sure power is OFF. Remove junction box cover “A”. Locate the three with stripped |PRE-TEST CHECKLIST dishwasher wires, (white, black and green) Open ends.
Installation Instructions STEP 15 |DISHWASHER Turn on power WET supply (or plug power cord TEST STEP 16 |REPLACE TOEKICK into outlet, if equipped). Turn dial to Normal “Wash” position. Close door. Check to be sure that water does and not enter power the enters the dishwasher. dishwasher, are turned check to be sure If water that water on. Check for leaks under the dishwasher. If a leak is found, turn power supply off, then tighten connections.
