SENSOR SMART TMGas Dryer KING SIZE TMCapacity Plus Secadora de Gas SENSOR SMART TM de capacidad extra grande (KING SIZE TM"Plus") 3979096A Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.
TABLE OF CONTENTS WARRANTY WARRANTY ..................................................................................... 2 DRYER SAFETY .............................................................................. 3 INSTALLATION INSTRUCTIONS .................................................. Tools and Parts ............................................................................ 5 5 Location Requirements ............................................................... Electrical Requirements...
DRYER SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING.
IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions, including the following: • • Read all instructions before using the dryer. Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.
INSTALLATION INSTRUCTIONS Check that you have everything necessary for correct installation. Proper installation is your responsibility. • 8orl0in. • pipewrench • Knife 8 or 10 in. adjustable wrench (for gas connections) • Safety glasses • Vent clamps • Flat-blade screwdriver • Pipe-joint compound resistant to L.R gas • Adjustable wrench that opens to 1 in. or hexhead socket wrench (for adjusting dryer feet) • • Level • Gloves • _/_in.
Installation Clearances The location must be large enough to allow the dryer door to open fully. Dryer Dimensions Mobile Home-Additional Installation Requirements This dryer is suitable for mobile home installations. The installation must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280).
• Must include; shutoff valve: An individual shutoff valve must be installed within six (6) feet (1.8 m) of the dryer in accordance with the National Fuel Gas Code, ANSI Z223.1. The location should be easy to reach for opening and closing. 1 3 5 2 1. 2. 3. 4. 5. Explosion Hazard 4 _ in. flexible gas connector _8 in. pipe to flare adapter fitting _ in. NPTplugged tapping _/2in. NPT gas supply line Gas shutoff valve Use a new AGA or CSA approved gas supply line. Install a shut-off valve.
Burner Input Requirements: Elevations up to 10,000 feet (3,048 meters): • The design of this dryer is certified by CSA International for use at altitudes up to 10,000 ft (3,048 m) above sea level at the B.T.U. rating indicated on the model/serial number plate. Burner input adjustments are not required when the dryer is operated up to this elevation. • Do not install flexible metal vent in enclosed walls, ceilings or floors. Use clamps to seal all joints.
Optional exhaust installations This dryer can be converted to exhaust out the right side, left side, or through the bottom. NOTE: The following kits for close clearance alternate installations are available for purchase. For further information, please call t-800-4-M¥-HOME _ (1-800-469-4663). • Over-The-Top Installation: Part Number 26-49900 Periscope Installation (For use with dryer vent to wall vent mismatch): Part Number 26-49901 - Less than 5 in. (12.7 cm) mismatch Part Number 26-49908 - 5 in. (12.
2. Determine vent length. The chart below helps you determine your maximum vent length based on the number of 90 ° turns or elbows you will need and the type of vent (rigid or flexible metal) and hood that you will use. The maximum length of the exhaust system depends upon: • • The type of vent (rigid metal or flexible metal). The number of elbows used. • Type of hood. Recommended hood styles are shown here. 2 (10,2 Vent Length Chart Number of 90 ° turns or elbows cm) 1. Louvered hood style 2.
3. Examine the leveling legs. Find the diamond marking. 1 4. Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the diamond marking is no longer visible. 5. Place a carton corners. Stand posts until it is to connect the 6. Once connection is made and dryer is in final location, remove corner posts and cardboard. 1. Remove the red cap from the gas pipe. Move the dryer close to its final position. 2.
1. Using a 4 in. (10.2 cm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust outlet and inside the exhaust hood. Make sure the vent is secured to exhaust hood with a 4 in. (10.2 cm) clamp. 2. Move dryer into final position. Do not crush or kink vent. Make sure dryer is level. 3. (On gas models) If flexible metal tubing is used, check to be sure there are no kinks in the flexible gas line.
DRYER USE SELECTCYCLIE MODIFIERS t G* DR,nMI O C_t _V#, O WrlN_ 6_ CONTROL O OtB_ U'IT_ O HIIIH Hm MBDHHIGH MBDIUM Hr_vY DLJ_Y LOW O O ULlqM LOW It _10MUM NORMAL MINIMUM The following is a guide to starting your dryer. Periodic references to other sections of this manual provide more detailed information. 1. Check lint screen. Clean if needed. 2. Put laundry into dryer and shut door. See "Loading." 3.
Cycle tips • Dry most loads using the preset cycle settings, Use this chart as a guide to dry various loads. Drying temperature and Auto Dry Level (Normal Dry) are preset when you choose an Auto Dry cycle. You can select a different dryness level, depending on your load (see "Modifiers"). To stop your dryer at any time Press STOP/CANCEL or open the door. • To pause the dryer at any time Open the door or press STOP/CANCEL For a Timed cycle, drying temperature can be adjusted.
Bulky Items Use this cycle for drying large, bulky items that dry quickly on the outside, but stay wet on the inside. This cycle uses medium heat. Follow the progress of your dryer with the Drying Status indicators. DRYER STATUS i DRYING Delicate/Casual Use this cycle to get low heat for drying synthetic fabrics, washable knit fabrics and no-iron finishes.
You can customize your cycles by selecting options. OPnONS o HEAW DlffY o DELICATE When you select a cycle, the preset Auto Dry Level (Auto Dry) or Timed Dry settings for that cycle will glow. Modifiers allow you to change the preset settings and fur[her customize your cycles. Auto Dry Level with Ultra Moisture Sensing Auto Dry Level with Ultra Moisture Sensing provides the most accurate drying results in the shortest time.
6. You must select a time by pressing the MORE TIME or LESS TIME pads. Refer to the following table. 7. Start the dryer. To remove the dry rack, lift it straight up and out of the dryer. You can change Cycles, Options and Modifiers anytime before Star[ is pressed. • A short tone sounds when a change is selected. • Two short tones sound if an unavailable combination selected• The last selection will not be accepted. Changing Cycles after pressing 1. Press STOP/CANCELtwice. is Start 2.
Every load cleaning The lint screen is located in the door of the dryer. Clean it before each load. A screen blocked by lint can increase drying time. To clean 1. To clean the dryer drum 1. Make a paste with powdered warm laundry detergent and very water. 2. Apply paste to a soft cloth. OR Apply a liquid, non-flammable household cleaner to the stained area and rub with a soft cloth until all excess dye is removed. 3. Wipe drum thoroughly with damp cloth. 4.
Dryer will not run TROUBLESHOOTING • First try the solutions suggested here and possibly avoid the cost of a service call. Dryer displaying Checkthe following: Is the power cord plugged in? Has a fuse blown, or has a circuit breaker tripped? Was a regular fuse used? Use a time-delay fuse.
Items shrinking • Wasthe dryer overloaded? Dry smaller loads that can tumble freely. • Bid theload overdry? Check the manufacturer's load type (see "Cycles"). care label. Match dryer setting to Loads are wrinkled SERVICE Master Protection Agreements Congratulations on making a smart purchase. Your new Kenmore®appliance is designed and manufactured for years of dependable operation. But like all products, it may require preventive maintenance or repair from time to time.
Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME ® (1-800-469-4863) Call anytime, day or night (U.S.A. and Canada) www.sears.com www.sears.