OWNER'S MANUAL SWA/RS SEWING MACHINE MODELS 10101/11101/12551/12621/14401 14501/14502/14571/14572 Part# 6027i9
Sears, Roebuck and Co. Dear Homemaker, CONGRATULATIONS ! You have just invested in a very fine zigzag sewing machine. Here are just some of its special features: * Full rotary shuttle with slanted bobbin -- quiet and smooth running, easy access to bobbin, best stitching performance and easy maintenance with one-touch retainer system. *Ultra-stitchhelps make uniform stretch stitches and buttonholes every time.
TABLE OF CONTENTS III III I 1. KNOW YOUR MACHINE Locate and identify the parts on your machine ................................ 2 -3 Locate and identify the accessories .... 4 - 6 2. PREPARE YOUR MACHINE FOR SEWING Set up the machine ....................... 7 -8 *Plug in the machine and switch on the power .................................. 7 *Set the foot control ......................... 7 *Adjust the presser foot ..................... 7 *Put thread on th_spool pin ...............
1. KNOW YOUR MACHINE Locate and identify the parts on your machine After you have unpacked your new machine, set it on a flat, sturdy surface. Study the following diagram so that you will know the working parts of your machine. Thread guide Take-up lever Threading channel Top thread tension control You may need to refer to these diagram often while reading the instructions in this manual. =O A_essory Extension table box/extensi Thread cutter ** Presser foot release lever ** Thread cutter .
** Bobbin winder shaft ** Bobbin winder latch ** Stitch width control Stitch selector Stitch length control *Model 14571, 14572, only **Model 14501, 14502, 14571, 14572 only "* Stitch length indicator Reverse stitch lever Bobbin winder stop Bobbin winder shaft I" Hand wheel Clutch knob Spool ** Extra spool pin Fold-away carrying handle .
II Locate and identify the accessories You should find the following accessory box. items in the (Model 14501, 14502, 14571, 14572 only) S Needle set Bobbins 4 Spool pin caps large - No. 65653 small - No. 65652 Feed cover plate No. 60934 Screw drivers large - No. 65811 small - No. 65812 Satin stitch foot No. 657"/1 Satin stitch foot No. 57998 Spool pins No, 44999 Lint brush No. 65650 Zipper foot No. 6792 Extra spoolpin No, 64083 Straight stitch foot No. 6873 Zipper foot No.
1 You should find the following items in the snap-in automatic buttonhole attachment box. (Model 14501, 14502, 14571, 14572 only) Buttonhole guide plate No. 65665 Buttonhole templates 1 -- No. 65660 2 - No. 65661 3 - No. 65662 Buttonhole adapter No. 64061 Buttonhole foot No. 57979 Parts and accessories fitted on the machine Standardzigzag foot No. 65770 Needleplate No. 64156 Standardzigzag Presserfoot Presserfoot thumb Needleclamp foot No. 57985 holderNo. 56475 screwNo. 135 screwNo.
II I II Optional accessories Optional accessories help simplify the detailing that give your sewn garments a "professional" look. Q FOOT (No. 65820) Q NEEDLE (No. 6746) Even-feeding foot (No. 6887) -- Feeds both fabric layers simultaneously to help prevent bunching of Ultra Suede fabric, satin, tricot or other slick fabrics; eases pattern matching. Q SET (No. 6986) - Helps avoid skipped stitches, especially with synthetic, stretch and knit fabrics. Blind hem foot (No.
2. PREPARE YOUR MACHINE FOR SEWING Set up the machine 1. Be sure your machine is resting securely on a sturdy, flat surface. 2. You may want to practice with a scrap of fabric to absorb any dirt or grease. Plug in the machine and switch on the power 1. a. Plug the foot control into the machine. b. Plug the cord into 110-120 volt A.C. wall outlet. Turn on the power/light switch. Be sure to turn off the power/light switch if you are interrupted or stop sewing.
Attach th.e spool pins i 1. Check pins. the accessory box for two spool 2. Attach the spool pins at the rear of your machine, using the large screw driver. Put thread on the spool pin 1. a. Swing the spool pin away from you and fully to the back of the machine. b. Place a spool of thread on the spool pin. Secure it with a suitable size spool cap which is similar to the size of the spool, to ensure smooth flow of thread. NOTE: Remember to return the spool pin under the arm for storage. 2.
i Prepare the bobbin Load Thread on the Bobbin ® ® ® ® 1. Disengage the clutch by turning the clutch knob toward you. b. Start the machine by pressing down on the foot control. 2. a, Put a spool of thread on the spool pin. NOTE: The bobbin will stop turning when it is filled. b. Draw the thread from the spool through the thread guide. 3. a. Wind the thread around the bobbin several times in the direction of the arrow. b. Place the bobbin winder shaft. onto 4. a.
_!1 I III Prepare - the bobbin Load Thread on the Bobbin (Model 14501, 14502, 14571, 14572 only) ® (Model 14571 ) (Model 14501 ) ® ® ........ t. 1. Disengage the clutch by pulling the i_and wheel out (Model 14571) or turning the clutch knob toward you (Model 14501). . a. Put a spool of thread on the spool pin. NOTE: The bobbin will automatically turning when it is filled. stop b. Place a suitable size spool cap over the spool. 5.
Remove the Bobbin Shuttle Case from the 1. Remove the extension table from machine by pulling it to the left. the 2. a. Open the bobbin access cover pulling it down at the notch. by ® Bobbin case b. Use your forefinger and thumb to pull open the latch on the bobbin case. c. Pull the bobbin case out of the shuttle. Bobbin access, cover Notch 3. Turn the bobbin case upside down and the bobbin will drop out of the case.
Insert the Bobbin into the Bobbin Case ® ® 1. Insert the bobbin into the bobbin case with the thread running counter clockwise. 2. Pull the thread bobbin case. through the slit in the 3, a. Pull the thread underneath the lfl_ tension spring. It will clock when it is in place. bo Pull 3 to 4 inches of the thread from the bobbin case. Insert the bobbin Case into the Shuttle \ \ Locating groove \ Notch 1. Hold the bobbin case by the latch, with the locating groove downward. 2.
Prepare the Needle Top Use the correct Kenmore needles. The size of your needle should match the size of the thread and both should match the fabric. Kenmore needles are color-coded by size for your convenience. See the Needle, Thread, Fabric and Stitch Length Chart. NOTE: 1. Never use a bent or dull needle. 2. If you do not have a Kenmore needle, use this illustration to be sure your needle is right size. Distance from the top to the eye of the needle should be this exact length.
f Needle, Thread, Fabric and Stitch Study this chart to help you select size needle to match your fabric size.
Prepare the Top Thread Thread the Needle \ D C A B 1. Raise the presser foot lever to allow the thread to pass between the tension discs in the threading channel. 2. Raise the thread take-up lever to its highest position by rotating the hand wheel toward you. 3. Place a spool of thread on the spool pin. 4. Place a suitable size spool cap over the spool. 5. Lead the thread through the thread guide (A) and pull it toward you with your right hand until it clicks.to ensure it is threaded correctly. 6.
Pick up the Bobbin Thread 1. Raise the presser foot lever. 2. a. Hold the top thread loosely in your left hand. b. With your right hand, rotate the hand wheel toward you until the take-up lever has come to the top again. 3. a. Pull the top thread with your left hand to bring up the bobbin thread. b. Pull the bobbin comes through needle plate. thread the until the end opening of the 4. Pull both threads under the presser foot toward the back of the machine.
Check the Thread Tension STRAIGHT Adjust STITCHING the top thread tension Straight stitching The good looking appearance of your stitching is largely determined by the balanced tension of both top and bobbin threads. The tension is well balanced when these two threads 'lock' in the middle of layers of fabric you are sewing. NOTE: For most fabric the top thread tension should be balanced within the orange zone between 2 and 4 on the thread tension control.
:lj_I Choose the Right Presser Foot You will need change your presser foot match the stitch you have chosen. to Know what the presser feet will do Standard zigzag foot (Fitted on the machine) Use this foot for the general sewing with both striaght and zigzag stitching. Straight stitch foot Satin stitch foot Zipper foot This foot is grooved to permit dense stitching to pass under it easily. Use it for appliqueing, bar tacking, embroidery and monogramming.
I I / Change the presser foot Snap-on Presser foot holder presser feet 1. Bring the needle to the up position. ! 2. Raise the presser foot lever. 3. Push the foot release lever and the presser foot will drop off. 4. Place the new foot on the needle aligning needle holes. Foot release_,_ lever plate 5. Lower the presser foot lever so that the presser foot holder snaps on the foot. 6. Push down the presser foot thumb screw to engage the foot holder and the foot securely.
IIII I I II I Er ,¸ IIII L I Use the Feed Cover Plate The feed dogs automatically feed the fabric. If you want to prevent the feed dogs from feeding the fabric, use the Feed Cover Plate which covers the feed dogs so that they do not touch the fabric. NOTE: Use the feed cover plate when sewing on buttons, making buttonholes with the snap-in automatic buttonholer and darning. 1. Insert the two knobs on the feed cover plate into the two holes on the fabric feed area.
3. LEARN TO USE THE CONTROLS I!¸ Your machine has many special features to make your sewing both easy and accurate. Take a minute to look at the three controls that regulate your stitches. Stitch Selector Your sewing machine can make a variety of stitches. They are pictured on the Stitch Selector Dial. In addtion, there are three buttonhole steps pictured on the dial also. Orange patterns_ NOTE: Beginning on page 24, you will find detailed instructins on the use of each stitch.
I Stitch Width III Control (Model 14501, 14502, 14571, 14572 only) 1 • 2 • 3 '--_" 5 -_ The width of all stitches produced on this machine (except the straight stitch) can be made narrower or wider by adjusting the stitch width control. To decrease or increase the width of a stitch, slide the stitch width control from 1 - 5. The higher the number the wider the stitch. When straight stitching, set this control at "1" to achieve uniform straight stitches.
4. PRACTICE GOOD HABITS -- Before you begin to sew 1. Check the needle: a. Is it inserted properly ? (See page 13) b. Is it the correct size for your fabric ? (See the chart on page 14) c. Is it threaded properly ? (See page 15) d. Is it straight and sharp ? NOTE: Many synthetic fabrics dull your needle quickly. Be sure to replace needles often. 2. Check the threads. a. Are they both on top of the needle plate surface ? When b. Do you have 3-4 inches pulled toward the back of the machine.
5. LEARN TO USE THE STITCHES I Machine I Setting Chart The following pages will show you how to: 1. Set the Stitch Selector. 2. Set the Stitch Length Control. 3. Set the Stitch Width charts, select and sew a variety stitches shown below. 4. Use the stitch correctly. Control. NOTE: You may want to use fabric scraps to experiment with these stitches. This manual will show you the best uses of these stitches. NOTE: Machine settings are graphically shown for your quick reference.
Straight Stitches Top thread tension control Stitch width control z Stitch selector 0 '1" to obtain uniform stitches. See page 17. Stitch length control Presserfoot f *Straight _. foot or zigzag straight foot will give you best control. You _NOTE: For most straight stitching, the I may use the zigzag foot if you prefer. 12 or orange range ._ NOTE: Always beoin your first stitches by turning the hand wheel toward you to lower the needle into the fabric.
Cornering guide Square the Corner 5/8" from the fabric edge . Stop stitching your 5/8 inch seam when the fabric is even with the cornering guide (cross marks). Leave the needle in the fabric. a° b. 2. a. Lift the presser foot. b. Turn the fabric so that the unstitched side is lined up with the seam guide. Co Lower the presser foot and stitch in the new direction. Top-stitching Top-stitching improves the appearance of a tailored garment and at the same time holds facings in place.
IIII I Basting , Set the stitch length control at 6. 2. Set the top thread tension control at 1 - 2 to facilitate pulling out bobbin thread. , Insert pins at right angles to the seam line, with the tip of pins just touching the seam line. NOTE: Pins must not come in contact with the feed dogs. Never pin on the underside of the fabric. = 4. Sew over the tip of pins slowly. NOTE: If in doubt about sewing over pins, remove each pin as you approach it. Gathering ° Set the stitch length control at 6. 2.
Attaching a zipper 1. To sew down the right side of the zipper, attach the left side of the zipper foot to the presser foot holder so that the needle passes through the opening on the left side of the foot. 2. To sew down the left side, attach the right side of the foot to the foot holder. Needle to left of foot Needle to right of foot Cording * Use the zipper foot to make cording for slip covers, pillows etc. 1. Attach the right side of the zipper foot to the presser foot holder. 2.
Zigzag stitches Stitch width control Top thread tension control f I w 0.2 4.6.8 See page 17. 1-5 resser,oot Zigzag foot _-_ Stitch selector II Stitch length control [1 or orange rangej Models with stitch width control Models without stitch width control The simple zigzag stitching enables you to do many exciting things with your sewing machine. Beyond basics, you'll use this stitch to applique, embroider and monogram.
Overcasting stitch * Choose this stitch to keep seams or fabric from raveling. NOTE: To reinforce seams with overcasting, it is recommended to use the threestep zigzag (see page 33). 1. Stitch so that the point of the zigzag clears the raw edge of the fabric. Satin stitch Closely spaced zigzag stitches are called satin stitches. I0 * Choose this stitch for bar tacking, appliqueing, embroidery and monogramming. 1. Set the stitch length control at the orange line between 0 and 24. 2.
Applique To applique a design on a sewing project or garment: 1. Baste the applique to the top of your fabric. 2. Then use satin stitch to attach permanently. You may want to use a contrasting color thread. NOTE: For best results, be sure your satin stitch covers the bottom fabric and the top fabric. Embroidery and Monogramming Satin stitch method Satin stitch can be used to produce many different designs and patterns. 1. Set controls the same as for satin stitch. 2.
Button sewing 1. Attach the feed cover plate (see page 20). 2. Use clear tape to fix the button on your fabric before stitching. NOTE: When sewing a flat button, place a pin between the holes so your button will be loose enough for easy buttoning. . Align the two holes of the button with the slot of the presser foot. 4. Lower the presser foot. 5. Turn the hand wheel by hand until the needle point is just above the button. Feed cover 6.
I I Three-step il I I I Zigzag i Stitch width control Top thread tension control Stitch selector f- S f page 17. Presser foot ___ = _ 4-5 I ,, ! == itch length control I I ; IIIn:l • • 12-1-' t ' gg ) ' L_ i ,-I l!"il \ 12 or green range ,,) NOTE: Three-step zigzag takes three short stitches, where regular zigzag takes one. * Choose this stitch to mend a tear or to overcast a raw edge. To Mend: 1. Put a piece of fabric under the tear to be mended. 2.
Blind Hem Stitch width control Top thread tension control I 0 f . 2,__r[_===_• 6 B_ • I See page 17. . 2 . 3 5__ "-_' Stitch selector t 2 - 5 (Green range) Presser foot kI Stitch length control IlUi Zigzag foot --V-V....V- j I taFo°_eSe_s!h:_ _!_d _b._!6_ -- Regular blind stitch for normal fabrics :!eieSp!ii_) m;t_ed 12 or green range j * Choose this stitch to use on garments and especially on curtains and drapery hems so that stitches need not show on the front of the fabric.
2. a. Fold the garment away from the hem. ® b. Leave1/8 inch of the hem edge exposed. FINISHED EDGE 3. a. With the wrong side up, place the fabric under the foot. ® b. Lower the presser foot. c. Stitch so that the needle just pierces the fold when the needle swings to the left. 4. Unfold the garment flat.
I1_ II I Box Stitch i Top thread tension control Stitch width control Stitch selector f 1 .2 .3 4 5 3 -- 5 (Green range) 0 1 Presser foot Stitch length control Zigzag foot 12 or green range * Choose this stitch to sew flat overlapped seams or to decorate a finished edge on lingerie or nightwear. To Sew Overlapped Seams: 1. a. Overlap the raw edges of two pieces of fabric. b. Stitch so that the stitches pierce both pieces of fabric on the left and right sides.
I Shell Stitch Top thread tension control Stitch width control " 0 • 2--'_ S • 6 • B _ _ Zigzag foot I _ _ ' 3 '--_' , 3-5
Stretch Stitches Stitch width control Top thread tension control f O, _'--_, 6 • 1 " 2 8 See page 17. ' 3 '-_" 5 --_ 2 -- 5 (Yellow range) Stitch selector 1 Presser foot Stitch length control Zigzag foot 6-- 12 (Yellow range) f J These eight stitches are built into your machine to use with stretch and knit fabrics: {.. rx/ V_ v_ V_ V_ V_. V_ v_ 1. 2. 3. 4. 5. 6. 7.
_1 II Where to Use Which Some Stretchy Stretch Stitch: Suggestions... 1. To keep loosely constructed knits from catching on the toes of the presser foot, wrap a short strip of transparent tape of the presser foot encasing both toes. A Check-Chart 3. Test the thread tension and stitch on a scrap of the same fabric you will use. 4. Knits contain more yarn (and more lint) than woven fabrics. Check often and clean the bobbin case area. 2. To avoid tangled threads, start seams carefully.
v Tips on Sewing Different Fabrics The chart below provides many details but you'll also want to remember... * Soft or fine fabrics may require a backing or interfacing of paper, especially where stitches are close together. * When working on tweed or other multicolored bulky fabrics, use one color thread in the bobbin, another on the top. (Great for repairs-the "patch" practically disappears.) * When sewing knits use a strong, fine thread together with "Q NEEDLE"._.
Straight Stretch Stitch * Choose this stitch to strengthen curved seams on all fabrics or to do all straight stitching on knit or synthetic fabrics. 1. Sew as you do with the regular straight stitch. Rick-Rack Stretch Stitch * Choose this stitch for knits and synthetic fabrics whenever you want a zigzag stitch. Also use this stitch as a decorative top stitch. 1. Sew as you do with stitches. the regular zigzag Smocking Stretch Stitch * Use this stitch as a decorative stitch.
III Overcast Stretch Stitch * Choose this stitch to seam and finish the raw edge at the same time. Choose this stitch to repair raw or worn edges of older garments. I. To seam and overcast at the same time, you must have the raw edges of your fabric to the right of your needle. NOTE: To achieve this same effect, the serging stretch or overlock stretch stitch can be used with the raw edges on the left side of the needle.
Overlock Stretch Stitch * Choose this stitch to overcast loosely constructed knits or woven fabrics, because threads lock in the middle to reinforce seams for more durability. Elastic Edge Stretch Stitch * Choose this stitch in preference to the overcast stretch stitch for overcasting stretch or knit fabrics where strength and flexibility are required. 1. Sew as you do with stitch.
6. LEARNING TO SEW BUTTONHOLES -,J With your Kenmore sewing machine you have two methods of making buttonholes. You may use the built-in system or you may use the snap-in automatic buttonhole attachment system. Choose the buttonhole style . Built-in or manual buttonholes (rectangular) Choose this style for waistband, cuffs, belt slots or where you will need only one or two buttons. 2. Round end buttonholes (Template No.
I Manual Method Top thread tension control O, II 2 4 Stitch selector .6,8 See page 17. Presser foot t h control -5 J 1. a. Carefully mark the buttonhole length on your garment. Q b. Insert it under the presser foot with the left side of buttonhole under the needle. Diameter of button plus 1/8". 2. a. Make sure the needle swings to the right and pierce the fabric at point A. b. Stitch to the end of the marking and stop with the needle in the fabric on the right side of stitching (point B).
I III II 0 ® 3. a. Raise the presser foot fabric. and turn the b. Turn the stitch selector to the fourth narrow zigzag position. c. Lower the presser foot and take one stitch to the left (point B to C). ® O. 4. a. Raise the presser foot with the needle in the fabric. b. Turn the stitch selector to the widest zigzag position. c, Bartack about three stitches and stop with the needle on the left side of stitching (point D). 0 ® 5. a. Raise the presser foot. b.
Built-in Method Top thread tension control 0-2 4 ,6, B See page 17. Stitch width control 1 .2.3 4 1 5 *3.5 -- 4.5(Blue * Adjust the stitch width (Model 14501, 14502, 14571, 14572 only) You may adjust the width of the sides and the space in the center within the blue range (3.5 - 4.5) as shown, depending upon your fabric and buttonhole length. The space gets wider for wider buttonhole.
Make the Buttonhole Buttonhole guide 1. a. Carefullymark the buttonholelength on your garment. b. Mount the buttonhole guide onto the presser foot with the letter "F" at the • front so that the rear edge of the presser foot is at the end of the guide. c. Insert the garment underthe guide with the buttonholemarking running toward you. NOTE'.Line up the markings on the guide with the length you have marked to help you stitch accurately. Markings are engraved in inches. I'I, 2. a.
I I III I Corded Buttonholes (a variation of the built-in buttonhole) Corded buttonholes are a stronger variation of the regular buttonhole. You need to obtain filler cord (crotchet thread or buttonhole twist). 1. Cut a length of cord about twice the length of the buttonhole guide. 2. Fold the cord in half. 3. Hook the cord at its mid point on the spur Of the guide. 4. Pull both ends of the cord forward under the guide. 5. Sew your buttonhole so that the stitching covers the cord. 6.
Buttonhole Attachment System For more varied and accurate buttonholes, you will enjoy using the buttonhole attachment and templates. Know the parts and read carefully how to set up your machine properly. You will need these items for the buttonhole attachment system. ..
nlnn Set up the machine Top thread tension control ; O, 2 Stitch width control Stitch selector 4.6.8 See page 17. Stitch length control i Buttonhole foot Feed cover plate k. on needle I, ao Not necessary to adjust plate J Remove the extension table. Density control knob b. Raise the needle to its highest position. C. Remove the presser foot. d. Position the feed cover plate in place. 2, a. Open the bobbin access cover. b.
Jl! , ,_._.,--Guide a, plate bo Te_ _ When you have selected the template with the size and style buttonhole you need, slide the template into the guide plate under the knob, so that the stamped letters on the template point up. Turn the template knob until the size buttonhole you have chosen appears in the winSow of the guide plate. keomPlate advance_ Template _ -.,v v 4.
r Ill Make the Buttonhole 1. a, Mark your buttonhole position carefully on the garment. b. Insert your garment between the guide plate and the presser foot. C. [' Pierce the fabric with the needle at the far end of the buttonhole. d. Line up your fabric edge with the measurement markings on the far end of the guide plate. NOTE: If you want your buttonhole to be 1/2 inch from the garment edge, line up the fabric with the 1/2 inch markings each time you start to sew a buttonhole. 2. a.
7. CARE FOR YOUR MACHINE Chan_je the light bulb 1. Unplug the machine. 2. a. Using the screw driver, push down the lever located behind the presser bar and the bulb will come out. b. Push the lever to the right to lock. 3. a. Push up the bulb and turn slightly to the left. b. Pull down to remove it. 4. a. Insert the new bulb and turn it with some upward pressure until it stops. b. Push up the bulb and turn to the right to lock into place. 5. Push the lever back to the left and then up into the machine.
lib Clean the shuttle 1. Unplug the machine. 2. a. Use your forefinger and thumb to pull open the latch on the bobbin case. b. Pull the bobbin case out of the shuttle. (Fig. 1) 3, a. Turn the hand wheel until the open side of the retainer is at the top. b. Turn the retainer counter clockwise with your forefinger and thumb while holding the hand wheel, and it will be released. (Fig. 2) c. Remove the retainer and bobbin case i holder from the shuttle. (Fig. 3) J4. Clean the shuttle area with the lint brush.
8. CHECK CHART FOR PERFORMANCE PROBLEMS Your sewing machine is a precision instrument, designed to give you many years of troublefree sewing with minumum maintenance. If you have any performance problem, check the list below and you'll be able to solve the problem yourself. GENERAL PROBLEMS Machine does not sew. *Hand wheel or clutch knob is not returned to stitching position. - Push in or tighten clutch (see page 10). *Power line cord is not connected. -- Check plug.
Needle breaks. *Fabric is being pulled or pushed against machine feeding action. - Guide it gently. *Needle size is not correct for thread and fabric. -- See page 14. *Needle is not all the way up into the needle clamp (see page 13). *Presser foot holder is not fastened securely. - Retighten presser foot thumb screw. "_lhlI\ \\ THREAD PROBLEMS Thread bunches.
SEWING MACHINE Now that you have purchased your Kenmore Sewing Machine, should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co. Stores. Be sure to provide all pertinent facts when you call or visit. The model number of your Sewing Machine will be shown on your nomenclature plate on the back of your Sewing Machine. See page 3 for location.
