Manual

ManualsBrandsKenmore ManualsSewing MachineOfficial Kenmore sewing machine

1_8.t7S20

STRAIGHt STITCH ATTACHMENT ZIGZAGBITE FOOT CONTROL

POSITION DIMENSION

n n ham

CI_NTER LOW BAR 5.8 6813

PRESSERFOOTHEIGHT

LOWBARTYPE

ti.li MM

MINIMUM

5,2 MM

NEEDLE PL:TE SURFACE

HIGH OARTYPE SUPERHIGH OARTYPE

li.S MM

MINIMUM

S.2 MM

5.2 MM

FRONT FACINGSHUTTLE

SIDE FACINGSHUTTLE

SUPER HIGH BAR LOW BAR HIGH BAR LOW BAR

Dropfeed dog Pressdownpressureregulator to the mexvmumpressure Lowerpressurefoot lever Loosenthumbscrewandbe

sure presser foot vs seated properly T,ghten thumb screw

If adlustment _snecessary,raesepresserfoot feverand loosenscrewson presserbar holder Adlustthe he,ghtof presserfoot

from needle plate as specd,ed Confvrmthe hevghtof presserfoot by o completeturn of the handwheel Ttohtenthe screws

securely after adlustment

FIGURE A-F

Oimibuti,n ,f Noodle Swing

Dean| the noodle to its lowest pcaLtlon by turnln4;

the bsndwheol. At this neeole position, t-tu.nthe

ar[ItchwtdtheomrolfromOtoms.-.Imum and back

to O. and oote the _latamce needle travel= from

its center poaxtlon towa, r_ one slde.

•rum the haadwhae! Onecomplete turn, an4br/nl[

the naedJa to lie ]owens poaltlon q[;u_. ,_ow thla

ttme, the needle travele to the oppoeite side trom

Its center posLtton, _ you tux_ the stitch width

€0atrol from 0 to maxizoum, autdb:pek*.oO. Yots

ebe _a.*-ce needZe tz,..4yeIL

the Wee,no trAvolJ unev_'A dtJt_mcen from Its

€lmtsr position, loosen set screw (I), _mdadJust

pooP.fen of follower rocker pi.nby tu,'n_m4_eooen..

aria pin (2), until you obtain an oven dlstrtt'i'._tton

the needle _ M LU,atr-_ted (3), Tfpsen

the set screws se¢_rel), attar a_e_..

F T.GURE C-6

Summary of content (5 pages)

PAGE 1
Oimibuti,n ,f Noodle Swing 1_8.t7S20 STRAIGHt STITCH POSITION ATTACHMENT DIMENSION n CI_NTER ZIGZAG BITE Dean| the noodle to its lowest pcaLtlon by turnln4; the bsndwheol. At this neeole position, t-tu.n the ar[ItchwtdtheomrolfromOtoms.-.Imum and back to O. and oote the _latamce needle travel= from its center poaxtlon towa, r_ one slde. FOOT CONTROL n ham LOW BAR 5.8 L, 6813 PRESSERFOOT HEIGHT HIGH OARTYPE LOW BARTYPE ti.
PAGE 2
Feed Oeg Height P km :OR _O'IT ;AC;'4GSHUTTL-Z_ODELG, _LACE ;AUGE _ )OS........... , tS ,._ S-RATE2 .liT.THE :1g-GO-SIDEOF ,_ =_uo: _ACI'_ T'_E";[Z3L-_L;_TE..I,E_,._rE_.:_: FOOT. '.,H;LE TUR,r,I._G "HE .A;,CWHEELSLJWLf BY "_.ID,'-E _._,,:_aOSL] :_ '_OVE3_Y THE F_EDDOG ",E., _ . ;F 21OT,FEZDD{_ T_.---'. _ _RE CO ..,;.TvE', T PLACE THE GAbGE Um-SIDE-DO'_N"ITH T_E _O-S,DE FAC",_ ?.E '4EL5LEmLAT_. REPEAT THE S_4E PROCEDURE. THE GAUGE SHOULD NOT BE '.IOVE_.IF THE GAUGE IS HOVED, THE FEEDDOG TE_H ARE IOO HIGH.
PAGE 3
NEEDLE TIMING TO SHUTTLE NEEDLe" BAR HEIGHT SET STITCH LENGTH CONTROLAT O. TURNING HANOWHEEL. CHECk,TO SEE IF THE FEED DOG MOVESHORIZO,"iTALLY. AT 0 POSITION THE FEED DOGSHOULD NOT MOVE. IF FEED DOGMOVES, LOOSENTHE NUT (2) HOLDING SCREW(1). TURN SCREWEITHER WAY TO ELIMINATE MOVEMENTOF THE FEED DCG. A._TER ADJUSTMENT. TIGHTEN NUT (2) SECURELY. THE RADIAL TIMING GAUGESAND TEST PINS, AS ILLUSTRATED BELOW',ARE AVAILABLE FROI, I DIVISION 92, SOURCE192. THE KIT IS IDENTIFIED AS #69659.
PAGE 4
?h4_clearance -a.'" '"Oo""€," a_d _ en_e "d" a_ _ ¢r,ti¢ll po_f_tt,a _llatlon to "Jle nq41dletiming to shuttle. 114_lv41r.tn4.N parers Me v_lvaily derefm_Md 0v "41_'gthe Radial "1_ mlr_q_s. NOYI: No adlmsm4Rt it _ov_d for "Oimem_4_ C" to, t_ f_t.fa_ng muttJe mod4Js.Fat adju4tment for :Mo.mutsi* ragtime, lateelw mfef to FHIunl G.3. f_---..
PAGE 5
z eg Sy, h,,m eo _t sutch width _nUrol at maximum. TumJn| the ba.dwheel, check ar,d see if the needle side moUoa on the standard plane (0,0_4 inch above the upper surface of the needle plated at both needle poslUoM _f the mseht_,e produce| _n i_r_r pMtern U dluotl'_ed (&_, adjust t_ m_l_e m the following way, IMert pattern d_ee member I onto _be €',- Jl_fl, _d cMcXtor acle_ur_mte_ 0,020 _Ms betwees cam surface of I_ttern d_e at _1 sMrtsst diameter _.'ld €_ foUower rocker pJa.