SEWING MACHINE CABINET OWNER'S Model Number MANUAL 272.98300.490 Oak 272.98301.4_90 White 272.98302.490 Cherry ASSEMBLY PARTS LIST 98300-FC IMPORTANT: Read instructions before assembling.
Hardware Included (20) (2) #8xl/2" Panhead Screws ,o, #6x5/8" Panhead Screws (1) Right Wing (1) % Left Wing (1) 2 pc. Knob (2) Door Hinge (9) #5x1/2" Flathead Screws Gold t_/F_ P,_L-- _ (_" _ Wh te Ceramic H 983o0%j_ IM,030, on,, 98302 (32) _j' #8x1" Flathead Screws ,, _"_'T_:> (1) #9/32xl Bolt (4) Support Hinge _ _ '_'_ IOJ_]© I _x_ I° IIo II I 0 o___l /[ I (1) Custom Fitlnsert II 0 O_ / loHol _?_ook (16) #8x5/8" Flathead Screws _____ (1) Bronze 7/8" Bolt (8) _'_ i\_
UnderstandingHowthe "ARROW-LOC"CamFastenerWorks. TOWARDS ARROW HOLEIN EDGE 1. Position bolt in pre-drilled hole and turn until tight, 2. Press cam into pre-drilled hole until flush with surface, 4. To lock, rotate cam 3. Insert bolt through pre-drilled hole in edge of panel. until tight, using allen key provided. Cabinet Assembly Step 1.
Cabinet Assembly Continued: Step 2. Install Cams (25 total) into the holes provided in the cabinet parts shown below, pushing a cam into each hole until flush with the surface. The arrow on the Cams should be turned (using a regular screwdriver Bolts will enter. or Allen Key Provided) to face the hole in each edge where the Connecting Step 2A.
Step 3. Attach the Magnet to.the Partition by using (2) #6x5/8" Screws. Be sure to keep the magnet Strikes (metal) facing towards the front edge of the Partition (as shown in FIG, 2.) FIG. 2 .4_ 0 ./_y / _ (2) #6x5/8" Screws f__Magnet /°°/ Partition (viewed from left) Step 4. Next, attach the plastic Drawer Runners by using (32) #6x1" Flathead Screws (as shown in FIG. 4). DO NOT OVER TIGHTEN. 6x1" Flathead Screws FIG. 4 ® ( • @ • • / I ) Drawer Runners / I (. • • • • • • ) .
Step 5. Attach the Left and Right Wings to the Platform using (4) #8xl/2" Panhead Screws (as shown in FIG. 5). The long flanges facing outward and toward edge of Platform. FIG. 5 #8xl/2" Left Wing Panhead Screws ",,//// i 0 0 0 I I 0 °cl 0 Ii 0 o Platform Step 6. Attach the Wings (with Platform) to the Carriage of the Lift Mechanism by laying the Back (with Lift attached) in a flat position and aligning the top and bottom holes in Wing flanges with the holes in the Lift Carriage.
Step 7. Attach the (4) plastic Trays to the Door by inserting the (16) #8xl/2" Panhead Screws into the Door. The (3) smaller trays are mounted in the three top rows of predrilled holes, with larger tray mounted in bottom row. Attach Magnet Strike Plate with (1) #5xl/2" Flathead Screw. Attach (2) door hinges to Door with (6) #5xl/2" Screws (as shown in FIGS. 7 AND 7A). Long end attaches to door. #8xl/2" Panhead Screw t FIG. 7 I FIG. 7A \ 0 0 0 #5x1/2" Flathead Screw ¢I)¢..
Step 9. Place or tap Caster Clips, Inserts, (1) Locking Caster, and (1) Non-Locking Caster into Left Side (as shown in FIG. 9 below). Attach the back to Left Side by guiding Back onto Connecting Bolts in Left Side (as shown in FiG. 9), turn Cams to the Locked Position. Attach the Shelf and Front by guiding each piece onto the appropriate Bolts in the side, and turn the Cams to the Locked Position. FIG. 9 .w--'---.w Taped Edge Front f Back io @ J tI @ © ; 1 t _lt t ;t I I J io ! / Fla.
Step 10. Place or tap Caster Clip, Insert and Non-Locking Caster into the Partition (as shown in Fig. 10. below). Align the Connecting Bolts in Partition with corresponding holes in Front, Shelf and Back. Now, making sure the Partition is completely on the Connecting Bolts, turn Cams to Locked Position. FIG. 10 --- ;a sert .
Step 11. Attach Compartment Bottom and Compartment Back to Partition by guiding each piece onto Connecting Bolts in the Partition (as shown in FIG. 11). Turn Cams to Locked Position. FIG.
Step 12. Place or tap Caster Clips, Inserts, (1) Locking Caster, and (1) Non-Locking Caster into Right Side (as shown in FIG. 12A below). Attach Right Side by Aligning the Connecting Bolts in the Right Side to the holes in the Compartment Back and the Compartment Bottom (as shown in FIG.12). Turn Cams to Locked Position. After completing Step 12, carefully turn the Cabinet upright onto the Casters FIG.
Step 13. Attach the (2) Leaf Support Wings to outside of Right and Left Sides, on right and one Left with (8) #8 x 5/8" Flathead Screws. Now, attach the (2) Bronze Strike Washers for the Round Magnet to each side with (2) #5 x 1/2" Flathead Screws (as shown in FIG. 13). FiG. 13 Right Left Wing #8x5/8" Flathead Screw NOTE: Support Wings are to fold toward rear of cabinet. Step 14.
Step 15. The Door may be hung using (6) #5 x 5/8" Flathead Screws (as shown in FIG. 15). Next attach the Door Knob using (1) 7/8" Bolt for Ceramic Knob or (1) 8/32 x 1" Bolt For Metal Knob, this is a 2 pc. Knob Assembly as shown in FIG. 15. A. White Ceramic Knob FIG. 15.A 2 pc. Metal Knob (98300 + 98302 only) (98301 only) ! Sleeve I / FiG.
PLEASE NOTE: BE SURE TO KEEP GROVES IN DRAWER PARTS (FOR DRAWER BOTTOM) ALIGNED WHEN ASSEMBLING THE DRAWER. Assembling the Drawer Begin Drawer assembly by inserting Drawer Connectors into the ends of the (4) Drawer Backs, (as shown in FIG. A). Push Connectors all the way into the Drawer Backs until the tabs lock into place. F/_/_o ,=_ Drawer Back - E J_ Drawer Side - B II _--_,,_ II I I II I Drawer F, .B Drawer Connectors I II I Drawer Assembly [I I II I STEP1.
Installing Sewing Machine into Your new Cabinet. It may be helpful to read the directions for operating the mechanism before proceeding with the following steps. See page 16, and FIG. 19 on next page. FIG. 16 Step 1. Swing out the Leaf Support Wings and open leaves. To prevent damage to Cabinet surface, place cushioning material just to the left of cut-out. Lay the machine on its back, on top of cushioning material. Step 2.
To assist in selecting the platform holes best suited to properly position your sewing machine, refer to FIG. 18B below. Insert (Sears#9801) FIG.18B I Cabinet top Opening Determine measurement A & B on your custom-fit plastic insert and select platform holes which will properly place your machine in the cabinet top opening to allow it to fit with the insert when sewing in the flatbed position.
HOW TO MOVE YOUR MACHINE FROM ONE POSITION TO ANOTHER To move machine from free arm to flatbed (see Photos A, B & C). GENTLY push down on sewing machine until you hear a "click." The sewing machine is now locked in place at the flatbed position. To move machine from flatbed to storage (see Photos C,D&E. GENTLY push down on sewing machine until you hear a "click." The sewing machine is now locked in place at the storage position. NOTE: Your mechanism is adjustable.
Wood Parts and Part Numbers • _ " • B-Left Leaf A-Right Leaf " D-Left Side Panel |° / o o o E-Right Side Panel Finished Edge G-Back F-Partition H-Compartment Back (Left View) I-Shelf J-Compartment Bottom P-Drawer Front M-Platform L-Right K-Left Leaf Supports • °y . Bottom O-Door Ref. No. Description Oak Part No.
(J J) (cc) (KK) I°o oijol oO (_ (DD) (uu){_ (E) (LL) (F) __ (EE) (H)_ (MM) (V) (FF) (J) (w) (x) (oo) (L) __-__4-_1 (PP) (ss) *)© @ (z) (AA) (11) © % (AA).
Part Numbers Description #5xl/2" Flathead Screws #6x5/8" Panhead Screws #8xl/2" Panhead Screws Part No. 000916 000083 002614 _lef.
API Specialty Furniture (A Division of ARROW PRODUCTS, P.O. Box 410, Elkhorn, Inc.
