Installation Instructions Instrucciones de instalacion Instructions d’installation English / Espafiol / Frangais kenmore. . : P/N W10300759C Sears Brands Management Corporation Hoffman Estates, {L 60179 U.S.A. www.kenmore.com www.sears.com Sears Canada Inc. Toronto, Ontario, Canada Wi www.sedrs.
TABLE OF CONTENTS DISHWASHER SAFETY 2 INSTALLATION INSTRUCTIONS (CONT.) INSTALLATION REQUIREMENTS ...........sssssssssssssssssssessesseesseeees Make Power Supply Cord Connection .ssevsssssssesseesmnnnnssssseee 13 Tools and Parts Location Requirements Drain Requirements Water Supply Requirements Determine Cabinet Opening Custom Panel Installation Choose Attachment Option Move Dishwasher Close to Cabinet Opening... 14 15 15 16 Electrical Requirements Connect to Water Supply 18 INSTALLATION .
INSTALLATION REQUIREMENTS Parts needed: we fools and Parts Gather the recommended tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. 34"-Compr x %4" hose fitting. Contact your local Sears Store to purchase Kit Number:11000. All Installations Tools needed: Pliers LE.
Grounded electrical supply required. Check location where dishwasher will be installed. The location Do not run drain lines, water lines or electrical wiring where they can interfere with or contact dishwasher motor or legs. must provide: The location where the dishwasher will be installed must provide clearance between motor and flooring. Motor should not touch the floor. m easy access to water, electricity and drain. m convenient access for loading and unloading dishes.
Product and Cabinet Opening Dimensions hal" a oe *Insulation' may be compressed (not used_on all models) Check that all surfaces have no protrusions that would prohibit dishwasher installation. NOTE: Shaded areas. of cabi st walls show where utility connections may be installed, *Measured from the lowest point onth underside of the countertop. May be reduced to'33'4" (85.7 cm) by removing the wheels from dishwasher. ** Minimum, of.opening.
Electrical Requirements Drain Requirements m m Anew drain hose is supplied with your dishwasher. If drain hose is not long enough, use a new drain hose with a maximum length of 12 ft (3.7 m) (Part Number 3385556) that meets all current AHAM/IAPMO test standards, is resistant to heat and detergent, and fits the 1" (2.5 cm) drain connector of the dishwasher. Make sure to connect drain hose to waste tee or disposer inlet above drain trap in house plumbing and 20" (50.8 cm) minimum above the floor.
INSTALLATION INSTRUCTIONS ° Check water and electrical placement | Electrical Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher. Failure to do so can result in death or electrical shock. | 1 | Disconnect power } If the water line and the cable extend to the locations shown, proceed to the “Install Drain Hose” section. If they do not reach far enough, follow the instructions in the “Prepare Cabinet Opening—New Utilities” section.
2 | Power Supply Cord-Prepare hole cabinet Wood cabinet: Sand the hole until smooth. Metal cabinet: Cover hole with grommet included with power supply cord kit. Route cable from power supply through cabinet hole (cable must extend to the right front side of cabinet opening). Tape cable to the floor in area shown. This will prohibit cable from moving when dishwasher is moved into cabinet opening. Option B, Direct Wire: rem Dew te.
Attach water supply line Attach the water supply line (copper tubing or flexible braided line) to the hot water line using a connection configuration that is in compliance with local codes and ordinances. The water supply to the dishwasher should have a manual shutoff valve located under the sink. 4 | Route water supply line Slowly route water supply line through hole in cabinet. (If you are using copper tubing, it will bend and kink easily, so be gentle.
3 |. Fit rubber end of drain hose to waste tee and cut if needed. NOTE: Do not cut ribbed section. 2. Attach rubber end of drain hose to waste tee with a large drain hose clamp (provided). Use pliers to squeeze clamp open and move into position. If the drain hose was cut, use a 1%" to 2" (3.8 to 5 cm) screwtype clamp (not provided). Connect drain hose Connect drain hose to waste tee or waste disposer using one. of the following ‘options: « Option A, Waste disposer —.
Option D, No waste disposer — with air gap ae No waste disposer - _ with air gap Se Stine clamps oe AWARNING = Large drain mS “< hose clamp = Waste tee ty os Rubber hose connector Drain hose : Drain trap Tip Over Hazard Do not use dishwasher until completely installed. Do not push down on open door. Doing so can result in serious injury or cuts. 1. Connect rubber end of drain hose to air gap and cut if needed. NOTE: Do not cut ribbed section. 2.
Helpful Tip: Place cardboard under dishwasher until installed in cabinet opening to avoid damaging floor covering. Do not use door panel as a worktable without first covering with a towel to avoid scratching the door panel. Put dishwasher on its back Using a V4" hex head socket, nut driver or Torx® T20® Using two or more people, grasp sides of dishwasher door frame and place dishwasher on its back. screwdriver, remove terminal box cover. Retain for later use.
° Nalke Make Power Power Supply Supply Cord Cord Connectior Connection Option A, Power Supply Cord: Power Cord—Route into terminal box cord G Electrical Shock Hazard Electrically ground dishwasher. Connect ground wire to green ground connector in terminal box. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Power Supply Cord— Connect ground wire Route cord so that it does not touch dishwasher motor to lower part of dishwasher tub.
Connect wires black to black and white to white, using UL Listed/CSA Approved twist-on wire connectors (included with power supply cord kit). Determine Cabinet Opening Wiring configuration Power.
Option A, Countertop Attachment Built-up Floors—Add shims as needed Insert bracket Tabs.must point to the right Built-up floors: opening's floor extend into the area shown to the countertop. If the kitchen floor is higher than the cabinet - for example, the kitchen floor tile does not cabinet opening - add shims as needed in the bring the dishwasher up to 34" (86.
Option B, Side Attachment For marble, granite, or other hard surface countertops AWARNING NOTE: Remove the brackets from the parts package. 1 | Break end of bracket Excessive Weight Hazard Use two or more people to move and install dishwasher. Failure to do so can result in back or other injury. NOTE: Do not install kick plate until instructed to do so. Score line Move dishwasher close to Break off the end of the bracket along the scored line.
3 | Open and close door i ie ay Door falls open — Increase spring tension With another person holding the dishwasher to keep it from tipping, open and close the door a few times. If the door closes or falls open under its own weight, the door tension will need to be adjusted. Closes too quickly— Decrease spring tension When door is unlatched and door opens by itself, move the tensioner to a lower numbered hole and replace the screw. Reattach door spring to rear leg.
Align front of dishwasher with front of cabinet doors Adjust rear leveling legs (on some models) oN Align front of dishwasher door panel with front of cabinet doors. You may need to adjust alignment to be even with your cabinets. Check for plumb and if needed To raise the rear of the dishwasher, adjust the rear leveling leg using a Phillips screwdriver. Turn clockwise until the dishwasher is level front to rear.
Add 90° elbow fitting to the water supply line NOTE: To avoid vibration during operation, route the water supply line so that it does not touch the dishwasher base, frame or motor. Check for leaks Place paper towel under 90° elbow fitting. Turn on water supply and check for leaks. If leak occurs, repeat previous step. Connect the 48" compression fitting to the water supply line prior to installing the unit into the cabinet opening. Attach so that the 94" connection is facing upward as shown above.
° 3 | Hose clamp final position Black drain hose Electrical Shock Hazard connector Electrically ground dishwasher. Connect ground wire to green ground connector in terminal box. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. After hose is connected, remove towel.
Connect wires black to black and white to white, using UL Listed/CSA Approved twist-on wire connectors (not included). Wiring configuration Power supply wire: Terminal box wire: white white =< black -«———»- black Secure Dishwasher in Cabinet Opening thy iy nan 2 a 6 ® , Double-check dishwasher alignment in cabinet opening ground wire -«——»- ground connector 4 | Direct Wire—Secure cable -— in strain relief Check that dishwasher is still level front-to-back and side-to- side in cabinet opening.
Secure dishwasher to countertop Locate brackets on top of dishwasher and secure dishwasher to countertop with two, #10 x 2" Phillips-head screws (included). The dishwasher must be secured to keep it from shifting when door is opened. Check side attachment Side mount dishwasher to cabinet NOTE: If side mounting dishwasher to cabinet, you must drill pilot holes in cabinet to avoid splitting the wood.
Comp Option A, Install Access Panel - Plastic Panel 1 | Reinstall access panel and fasteners Insulation Insulation (on some models) (on some models) -~ Place the plastic access panel against the dishwasher leg. Check that grounding clip is attached to the lower panel. Position the lower panel behind the access panel. On some models there is insulation on the access panel that must fall 2? | Check access panel edge | behind the insulation on the lower panel.
3 | Check lower panel edge we Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Check that the lower edge of the lower panel contacts the floor. Adjust if necessary. Failure to follow these instructions can result in death, fire, or electrical shock. Power supply cord—Plug into a grounded 3 prong outlet Tighten access panel screws. Plug into a grounded 3 prong outlet.
Check Operation m Read the Dishwasher User Instructions that came with your dishwasher. m= Check that all parts have been installed and no steps were skipped. Check that you have all tools used. m= Start dishwasher and allow it to complete the shortest wash cycle. After the first 2 minutes, unlatch door, wait 5 seconds, then open door. Check that there is water in the bottom of the dishwasher tub. Check that dishwasher is working properly.
