MONITOR WITH DVD RECEIVER DDX8019 DDX8039 INSTALLATION MANUAL © B54-4532-00/00 (KV/RV) DDX8019_B54-4532-00_00_eng.indd 1 07.2.
Accessories 1 ..........1 2 ..........1 3 ..........2 4 ..........1 5 ..........1 6 ..........6 7 ..........6 8 ..........1 2 | DDX8019/DDX8039 DDX8019_B54-4532-00_00_eng.indd 2 07.2.
Installation Procedure 1. To prevent a short circuit, remove the key from the ignition and disconnect the - battery. 2. Make the proper input and output wire connections for each unit. 3. Connect the speaker wires of the wiring harness. 4. Connect the wiring harness wires in the following order: ground, battery, ignition. 5. Connect the wiring harness connector to the unit. 6. Install the unit in your car. 7. Reconnect the - battery. 8. Press the reset button.
Connection If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box.
Rear view FUSE ( 10A ) Cooling fan FM/AM antenna input Accessory 1 ILLUMI FRONT L REVERSE White/Black White FRONT R REMO.CONT REAR L Gray REAR R + To front right speaker Green/Black Green P CONT To front left speaker Gray/Black MUTE ANT. CONT + + To rear left speaker Purple/Black Purple + To rear right speaker EXT.CONT English | DDX8019_B54-4532-00_00_eng.indd 5 5 07.2.
System Connection USB terminal (iPod) USB terminal USB device (commercially available) USB device (commercially available) iPod RELAY 1 RELAY 2 Do not connect.
Optional Accessory Connection iPod (commercially available) Navigation System (Optional Accessory) KCA-iP300V (Optional Accessory) Audio Input iPod AUDIO IN Audio Output (Black) Connection cable (Included in the Navigation System) Visual Input iPod VIDEO IN Visual Output (Yellow) Rear view USB terminal iPod USB terminal (iPod) USB terminal iPod cannot be connected. Connection cable (Included in the Disc changer) Disc Changer etc.
Installing the Escutcheon For General Motors 1. Cut out accessory 4 to meet the shape of the opening of the center console. 2. Attach accessory 4 to the unit. Cut out to meet the shape of the opening in the vehicle. Accessory 4 For Volkswagen 1. Attach accessory 8 to the unit. Accessory 8 8 | DDX8019/DDX8039 DDX8019_B54-4532-00_00_eng.indd 8 07.2.
For Toyota/Scion 1. Cut out accessory 4 as illustrated. Cutting line Accessory 4 2. Fold double-sided adhesive (accessory 5) along the slit and attach it to accessory 4 cut-out against the center rib as illustrated. Use 2 pieces of accessory 5 for 1 accessory 4 cutout. 3. Attach accessory 4 cut-out to the unit. Accessory 5 English | DDX8019_B54-4532-00_00_eng.indd 9 9 07.2.
Installation for Monitor/Player Unit Firewall or metal support Screw (M4X8) (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Self-tapping screw (commercially available) Metal mounting strap (commercially available) Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip).
Removing Monitor/Player Unit Removing the Hard Rubber Frame (escutcheon) 1. Engage the catch pins on the removal tool 3 and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure. Accessory 3 Removing the Unit 1. Remove the hard rubber frame by referring to the removal procedure in the section . 2. Remove the Hex-head screw with integral washer (M4 × 8) on the back panel. 3.
DDX8019_B54-4532-00_00_eng.indd 12 07.2.
