KNA-DV3200(E)_ENG r8 03.7.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 2 Contents English Before Use .................................................3 Replacing Map Discs .................................4 Inserting the Map Disc ................................................4 Removing the Map Disc ..............................................4 Starting Up Navigation..............................5 Language Selection ...................................6 Markers (and Controls) Displayed on Maps ...................................
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 3 Before Use ■ Warning Messages ■ Before Use For safe usage please observe the following !!! Start the car engine before use READ THIS MANUAL FIRST Read this manual carefully before starting to operate the Kenwood Car Navigation System and follow the manual's instructions. Kenwood are not liable for problems or accidents resulting from failure to observe the instructions in this manual.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 4 Replacing Map Discs English Inserting the Map Disc 1 Slide the front cover downward to open the discinsertion slot. 2 Insert the map disc (facing upward) and close the front cover. Removing the Map Disc 1 Slide the front cover downward to open the discinsertion slot. 2 Press the eject button. 3 Remove the map disc and close the front cover.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 5 Starting Up Navigation Start up navigation and display the map of the area around your vehicle. 1 Turn on the car engine. 2 Read CAUTION carefully, and select The Opening screen appears, followed by the CAUTION screen. . CAUTION Most functions are inhibited while the vehicle is in motion. Please read the handbook for operating instructions. Always obey traffic regulations. The Current Position screen appears.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 6 Language Selection English You can change the language of the menu and the voice guidance. 1 Select 2 Select 3 Select your preferred language from the list. : : : : . Displays Displays Displays Displays • The LANGUAGE screen can also be displayed even if 5). • KNA-VC300 is regired for Voice Recognition. 6 English (Language). up to five previous items. the previous item. the next item. up to five of the next items.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 7 Markers (and Controls) Displayed on Maps Screens Before Setting Route Scroll the map 1 Time display Displays the current time. 2 GPS (Global Positioning System) marker Shows the status of the signal from the GPS satellite. When this marker appears, the GPS satellite signal is being received and used to calculate the position of your vehicle. 3 Map Orientation control Shows and Changes the Map Orientation.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 8 Menu Screen Change Chart English Destination Entry Stored Locations Language Navigation Set Up Route Options RDS-TMC
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 9 Map Operations Changing the Map Orientation Either the direction in which you are headed or north can be shown as upwards on the map. 1 Select or .
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 10 Map Operations English Changing the Map Scale You can increase or decrease the scale of the map. 1 Select or Selecting or to change the map scale. changes the scale of the map as shown left. • You can keep selecting or to continually change the map scale. • By touching the right of the scale bar after or is selected, you can directly change between 5 scale levels.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 11 Set Route Setting Destination Setting Destination by Scrolling the Map You can set the destination or way point if the exact address not known. 1 Touch the screen to scroll the map until destination point or way point. 2 Select (Destination or Way Point). Select (Destination). 3 is at the Route calculation will be carried out and the entire route will be displayed on the map.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 12 Set Route English ■ Selecting route When the destination set, it is simultaneously calculated for three types of route (Quick, Normal, and Short). You can select the route used actually out of them. 1 2 3 12 English Select . The calculation route can be selected from one of three types namely, Quick (the fastest route), Normal (the standard route), or Short (the shortest route). Select (Information). Details regarding the individual routes (i.e.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 13 Setting Destination from the Navigation Menu You can set the destination using various ways provided by the system. 1 2 3 Select Select . (Destination Entry). Select the item you want.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 14 Set Route English ■ Address Before Steps 3 1 (Destination Entry) 3 (Address) Enter the street name. If the some letters of a street name are entered, the desired street can then be selected from the displayed list. : Selecting this deletes the character that was last entered. Selecting it continuously deletes all the characters that have been entered.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 15 ■ Memory Point If you have stored a memory point, you can make it the destination. Before Steps 3 (Destination Entry) 3 (Memory Point) 1 Select the category for the desired memory point. 2 Select the desired Memory Point. : : : : 3 Displays Displays Displays Displays Select up to five previous suggestions. the previous suggestions. the next suggestions. up to five of the next suggestions. (Destination) or (Way Point).
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 16 Set Route English ■ Home/Stored Destination If you have already stored your home address, you can set this as your destination. Similarly, if destinations are stored in advance, they can be selected as the current destination in a one-touch operation. Before Steps 3 1 (Destination Entry) Select (Home) or destinations through . The map for the area around your Home location or around the stored destination will be displayed.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 17 ■ Previous Destination This lets you choose one of the most recent 100 destinations or way points and make it your new destination. Before Steps 3 1 (Destination Entry) 3 (Previous Destination) Select the Previous Destination from the list. : : : : 2 Displays Displays Displays Displays Select or up to five previous suggestions. the previous suggestions. the next suggestions. up to five of the next suggestions. (Destination) or (Way Point).
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 18 Set Route English ■ Motorway Entrance/Exit You can find the name of a motorway entrance or exit from those listed and make it your destination or way point. Before Steps 3 (Destination Entry) 3 (Motorway Ent/Exit) 1 Enter the name of the motorway and select 2 Select the name of the motorway you want. : : : : Displays Displays Displays Displays . up to five previous suggestions. the previous suggestions. the next suggestions.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 19 ■ Coordinates This function allows destinations to be set using latitude and longitude. Before Steps 3 1 2 (Destination Entry) 3 (Coordinates) Enter the latitude. This can be done using the number keys in combination with [°] (degrees), [‘] (minutes), and [“] (seconds). Enter the longitude. : : : : Switches Switches Switches Switches over over over over to to to to north latitude. south latitude. west longitude. east longitude.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 20 Set Route English ■ Junction Designate the junction with 2 street names, and search for the place you want. Before Steps 3 (Destination Entry) 3 (Junction) 1 Enter the 1st street, and select 2 Select the street you want from the list . : : : : Displays Displays Displays Displays . up to five previous suggestions. the previous suggestions. the next suggestions. up to five of the next suggestions. 3 Specify the 2nd street with the same operation.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 21 ■ Postcode This finds a location by its postcode and makes it the destination. Before Steps 3 (Destination Entry) 3 1 (Postcode) Enter the postcode and select through . To set your destination, see page 17. : This deletes the last character entered. Selecting it continuously deletes all of the characters entered. If a number of candidates exist as a result of, for example, different area codes, these will be displayed in a list.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 22 Route Guidance English Guidance Screen While driving along during route guidance, the directions for the next junction where you have to turn are shown as a Turn Arrow or Turn List. Directions are indicated by an arrow. Directions are indicated as a list. 1 2 Select (Screen configuration). Select either (Turn Arrow) or (Turn List). If no items are to be selected, the screen can be closed by selecting .
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 23 Display Dual map It is possible to perform two-screen display of maps. 1 2 Select (Screen configuration). Select (Dual map). If you wish to return to one-screen display, select (Single map). If no items are to be selected, the screen can be closed by selecting . If you wish to modify the display selections for the right-hand screen, touch the top of this screen. When the settings have been completed, select .
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 24 Route Options English Setting Route Options During route guidance you can change the route options, stop or check the route. 1 2 Select Select . (Route Options). The Route Options screen appears. (Search conditn): Set the method for route calculation between locations. (see page 25) (Detour): This calculates an alternative route from your current position within a specified distance. (see page 25) (Route Pref.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 25 Search Condition You can set the conditions and the mobile navigation system calculates a route. Before Steps 3 1 (Route Options) 3 (Search conditn) You can select , , or to reach the next way point/destination from the current position. : The route with the quickest time will be used. : The standard route will be used. (You can only select or to reach the way points after the next.) : The route with the shortest distance will be used.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 26 Route Options English Route Preferences The function allows settings to be made for the roads to be used and to start route calculation. Before Steps 3 (Route Options) 3 (Route Pref.) 1 Each time a button is selected it will toggle between usage and non-usage of the corresponding roads or ferries. 2 Select . • can be selected during route guidance. • The route will not necessarily follow the specified conditions.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 27 ■ Modification of Destination or Way Point Positions This function allows the calculated route will be displayed and the positions of the destination or way points to be modified. Before Steps 3 1 2 (Route Options) 3 (Dest. & Way Pt.) Select . Select (Change Location). 3 Select the button for the location to be modified. 4 Move 5 Select The map for the area around your current location will be displayed. to location and then select . .
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 28 Route Options English ■ Deletion of Destination or Way Points The destination or any way point which has been set may be deleted using this function. Before Steps 3 (Route Options) 3 (Dest. & Way Pt.) 1 2 Select the button corresponding to the destination or way point to be deleted. 3 Select displayed. Select Select 4 Select . when the confirmation message is to cancel the deletion. .
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 29 Display Route Use this function to display the entire calculated route. Before Steps 3 1 (Route Options) 3 (Display route) Select . The Entire Route screen appears. : You can set any areas you want to avoid from the list of street names. : Recalculates the route. If the data for the route cannot be shown on one screen, you can scroll using and . 2 Select .
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 30 Route Options English ■ Setting the conditions for simulation run Before Steps 3 1 (Route Options) 3 Select (Route Preview) . EDIT ROUTE PREVIEW screen apppears. : Stops at the destination or the next way point. : Stops at a point of interest which has been setup on the route. : Delete the POI which has been selected. POIs: Displays the six POIs from Quick-POI storage.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 31 Navigation Set Up Setting Navigation System You can alter the map display conditions, the route guidance conditions and show the system information. 1 2 Select Select . (Navigation Set Up). The NAVIGATION SET UP screen appears. Select a setting button while changing the screen using or . (User Settings): Allows you to change the settings for the screen display and sound.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 32 Navigation Set Up English User Setting You can change the settings for the screen display and sound. Before Steps 3 1 (Navigation Set Up) 3 (User Settings) Select the desired item. Select a setting button while changing the screen using Distance: Units for distance can be selected as or or . . Notify traffic restriction: The display of warnings during route guidance when passing through areas with traffic restrictions can be turned on or off.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 33 Quick POI Selection This function allows you to set the categories on that are displayed when the (Point of Interest) menu is selected the map. Quick POI enables you to store up to six different kinds of category which you use most regularly. (see page 48 to display markers on the map and search for nearby points of interest) Before Steps 3 1 (Navigation Set Up) 3 (Quick POI Selection) Select the button for Quick POI storage.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 34 Navigation Set Up English 2D/3D View You can switch between a 2D and 3D display screen. You can also change the viewing angle of the 3D display. Before Steps 3 1 (Navigation Set Up) 3 (2D/3D View) Select a 2D or 3D display for the Map Screen and the Guidance Screen. Map Screen: Changes the map screen display. Guidance Screen: Changes the route guidance screen, such as the enlarged junction diagrams. 2 Select or on the angle indicator.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 35 Calibration This function allows you to correct any error in the position or direction of your vehicle display. ■ Adjusting Current Position and Direction Before Steps 3 (Navigation Set Up) 3 (Calibration) 1 Select 2 Move 3 Use or to adjust direction in which you are heading, and select . . to the correct position and select .
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 36 Navigation Set Up English ■ Vehicle Signal This function allows vehicle and GPS satellite data to be displayed. Before Steps 3 1 (Navigation Set Up) 3 Select (Calibration) . VEHICLE SIGNAL screen appears. ■ Map Version This function enables you to check the version of the map disc you are currently using. Before Steps 3 1 (Navigation Set Up) 3 Select (Calibration) . The version of the map disc you are now using is shown.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 37 Set Clock The current time is set using this function. Since time notification is provided by a GPS satellite, time-zone adjustment can be carried out automatically. Before Steps 3 (Navigation Set Up) 3 (Set Clock) 1 Select 2 Select to move the setting ahead by one hour, and similarly, select to move it back by one hour. if you would prefer 24-hour display; for 12-hour display.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 38 Stored Locations English You can store, edit, or delete any destinations, way points, or marked point. 1 2 Select Select 3 . (Stored Locations). Select the item you want. (Memory Points): Places a marker on the map. (see page 39) (Avoid Area): Stores any areas to be avoided. (see page 43) (Dest. & Way Pt.): Sets the destination (and way points). (see pages 26 through 28) (Home): Stores the location of your home. (see page 44) (Previous Dest.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 39 Memory Points ■ Memory Point Storage Memory points can be classified into one of four categories for storage. Before Steps 3 (Stored Locations) 3 (Memory Points) 1 Select the category for storage of the memory point. 2 Select 3 Set a memory point using your preferred method. . Up to 100 memory points can be stored. You must delete a memory point that you no longer require (see page 42) before storing a new memory point.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 40 Stored Locations English ■ Memory Point Confirmation and Modification This function allows stored memory points to be displayed in list form and allows names, icons, telephone numbers, and the like to be modified. Before Steps 3 (Stored Locations) 3 (Memory Points) 1 Select the category of the memory point to be modified. 2 Select 3 Select the memory point to be modified. .
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 41 : Allows the name to be changed. When editing has been completed, select . Furthermore, select to display names on the map, or if these names are not to be displayed. : Allows memory points to be checked and modified on the map screen. After checking, select . : Allows the telephone number to be modified. When editing has been completed, select .
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 42 Stored Locations English ■ Memory Point Deletion Stored memory points can be deleted using this function. Before Steps 3 (Stored Locations) 3 (Memory Points) 1 2 3 Select the category of the memory point to be deleted. 4 Select displayed. Select . Select the memory point to be deleted. Select when the confirmation message is to cancel the deletion. ■ All Memory Point Deletion This function allows all memory point to be deleted.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 43 ■ Category Name Modification The category names — Personal, Business, Entertainment, and Market Point — can be changed if so required. Before Steps 3 1 2 3 (Stored Locations) 3 (Memory Points) Select the category whose name is to be changed. Select . Erase letters using select . , enter the new letters, and then Avoid Area ■ Avoid Area Storage This function allows the storage of Areas to be avoided when calculating routes.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 44 Stored Locations English ■ Avoid Area Confirmation and Modification This function allows stored avoid areas to be displayed in list form and allows them to be modified. Before Steps 3 1 2 3 (Stored Locations) 3 (Avoid Area) Select . Select the avoid area to be modified. Select the button corresponding to the item to be modified. For details regarding each button’s function, refer to (see page 40).
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 45 Previous Destination (Deleting Stored Locations) Previously-set destinations can be deleted using this function. Before Steps 3 1 (Stored Locations) 3 Select If deleted. 2 . is selected, all previous destinations will also be Select the destination to be deleted. : : : : 3 (Previous Dest.) Displays up to five previous suggestions. Displays the previous suggestions. Displays the next suggestions. Displays up to five of the next suggestions.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 46 Stored Locations English Preset Destination ■ Preset Destination Storage Up to five regularly-used destinations can be stored so that, when required, they can be set for the actual destination in a one-touch operation. Before Steps 3 (Stored Locations) 3 (Preset Dests.) 1 Select 2 Select a preset number. 3 Set a preset destination area using your preferred method. .
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 47 ■ Preset Destination Confirmation and Modification This function allows preset destinations to be displayed in list form and allows them to be modified. Before Steps 3 (Stored Locations) 3 (Preset Dests.) 1 Select 2 Select 1 through 5 in accordance with the destination to be modified. 3 Select the button corresponding to the item to be modified. .
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 48 Other Functions English Displaying POI’s on a Map You can select one of the six categories on the menu or List Categories and then select the POI(s) to be displayed on the map. 1 2 Select the screen. 3 Select the categories to be displayed up to a maximum of five. Select (Points of Interest). For categories other than the six displayed, select select them from the list shown. and : Allows you to search for a POI.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 49 Showing POI Data You can display POI (Point of Interest) data, such as name, address and telephone number. 1 2 Display the POI. (see pages 33 and 48) Select the desired POI by moving icon. on top of the POI The name of the selected POI appears. If no data is stored for the selected POI, the POI name is not displayed. 3 Select (Information). The POI’s data is displayed. : Stores the location of POI as a memory point.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 50 RDS TMC English If an RDS-TMC (KNA-TM320) is installed, it will become possible to display and use congestion information. (The RDS-TMC (KNA-TM320) is an optional extra.) RDS-TMC Settings Select the country where your car is located at the moment by touching the appropriate switch. 1 Select 2 Select 3 Select . Select . . (RDS-TMC).
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 51 Changing the country using TMC 1 Select or . : The Navigation System will automatically detect when you pass through a national border and will change the TMC service station to the current country. : Manual setting can be performed to set the country whose signal is to be received. 2 Select the desired country from the list. : : : : Displays Displays Displays Displays up to five previous suggestions. the previous suggestions. the next suggestions.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 52 RDS TMC English Displaying all traffic events 1 Select 2 Select to display the position of a traffic event on the map, or to display details and further information. . All traffic event are displayed in sequence from the current position. Displaying RDS-TMC Information RDS TMC Icon displaying on the map screen. The TMC Icon is shown on the Map screen when there is a TMC Tuner connected and there is TMC station reception.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 53 By selecting the Traffic Event you can get information about the selected Event.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 54 Remote Control English Remote Control Functions The KNA-RC300 Remote Control is used in the same way as the touch panel. (The KNA-RC300 Remote Control is an optional extra.) BAND DISC BAND MON NAVI AUD OUT OUT M/S ZOOM IN DISC MON NAVI AUD MENU IN PWR SRC POS ATT ENTER MENU CANCEL MENU PWR ROUTE DIRECT M/S ZOOM MENU CANCEL SRC POS NAV/ VIDEO ROUTE DIRECT ATT NAV/ VIDEO MODE VOICE SC1 AUDIO OPEN .
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 55 Shortcut Key Storage The remote control features a pair of shortcut keys, and these can be assigned to any functions that you use on a regular basis. 1 2 Select Select (Navigation Set Up). 3 Select (Remote Control). Select . to display the second page. 4 Select either 5 Select the function to be stored from the list. : : : : Displays Displays Displays Displays or . up to five previous suggestions. the previous suggestions.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 56 Voice Activate English Description If the KNA-VC300 Microphone & Talk switch is connected, it will be possible to control the Navigation System through voice recognition. (The KNA-VC300 Microphone & Talk Switch is an optional extra.) Talk switch Microphone • Care should be given to the following points to ensure that the voice microphone’s level of voice recognition is as high as possible while performing voice control.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 57 Basic Usage Pattern Voice control can be carried out by simply clicking the talk switch and speaking a voice command (see the following section) into the microphone. 1 Click the talk switch. The system will emit a short confirmation beep. 2 Speak the desired voice command. Upon recognition, the system will emit a confirmation sound.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 58 General Information English ■ Accuracy of the Vehicle’s Position ■ How the Vehicle’s Position is detected Area in which GPS signals cannot be received Detecting the vehicle’s position through the GPS Because the radiowave signals from the GPS satellites travel primarily by line of sight, the navigation system might not be able to receive the signals in the areas described below.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 59 Troubleshooting Confirm whether any problem is due to a minor operational error or a malfunction. Check the table below before contacting your local dealer for any repair service. The power does not come on. The fuse might be blown. Check the fuse. Replace it if it is blown. The map does not scroll even when the vehicle is moving. The screen shown might not be the Current Position screen. See page 7 of this manual to display the Current Position screen.
KNA-DV3200(E)_ENG r8 03.7.7 7:43 PM Page 60 Specifications English Specifications subject to change without notice. Navigation Section Antenna......................................................................................................................................Micro-strip patched antenna Receiver channel .......................................................................................................................... Digital 8-channels parallel Receiving frequency ...............