Kichler® Lighting 7711 East Pleasant Valley Road P.O. Box 318010 Cleveland, Ohio 44131-8010 Customer Service 866.558.
1 1. SAFETY RULES 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the National Electrical Code and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 10. Do not use water or detergents when cleaning the fan or fan blades. A dry dust cloth or lightly dampened cloth will be suitable for most cleaning. 3.
Sutter Place Premier TM 2 2. TOOLS AND MATERIALS REQUIRED Philips screw driver Blade screw driver 11 mm wrench Step ladder Wire cutters 3. PACKAGE CONTENTS e Unpack your fan and check the contents. You should have the following items: a. b. c. d. e. f. g. h. i. j. k. l. Fan blades (5) Ceiling mounting bracket Canopy Ball/downrod assembly Coupling cover Fan motor assembly Set of 5 blade brackets and Pre-Installed mounting screws Mounting plate Light fixture Glass shades (3) 40 Watt B10.
3 4. MOUNTING OPTIONS If there isn't an existing UL (cUL for Canadian Installation) listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers Outlet box Fig. 1 Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. The outlet box and its support must be able to fully support the moving weight of the fan (at least 50 lbs). Do not use plastic outlet boxes.
Sutter Place Premier TM 5. HANGING THE FAN NOTE: This ceiling fan is supplied with two types of hanging assemblies; a downrod and canopy mounting system and a "close to ceiling" Canopy ONLY system. The "close-toceiling" installation is recommended in rooms with less than 8-foot ceilings or in areas where additional space is desired from the floor to the fan blades. Once you have selected which mounting system you will use, proceed with the following instructions.
5 Step 4. Slip the coupling cover and canopy onto the downrod as Figure 7. Registration slot Check tab Fig. 8 Canopy Canopy cover Fig. 9 Screws and Lock washers (3 of 6 places) Thread the hanger ball onto the downrod, insert the cross pin previously removed from the ball/downrod assembly through the downrod and tighten. Now tighten the set screw previously loosened. (Fig. 6) Step 5. Lift the motor assembly into position and place the hanger ball into the ceiling mounting bracket. (Fig.
Sutter Place Premier TM 6. INSTALLATION OF SAFETY SUPPORT (required for Canadian installation ONLY) A safety support cable is provided to help prevent the ceiling fan from falling, please install it as follows. Step 1. Attach the provided wood screw and washers to the ceiling joist next to the mounting bracket but do not tighten. (Fig. 12) Step 2.
7 8. FINISHING THE INSTALLATION Outlet box STANTARD CEILING INSTALLATION Screws Step 1. Tuck all the connections neatly into the ceiling outlet box. Ceiling mounting bracket Screws Canopy Fig. 14 Step 2. Slide the canopy up to ceiling and attach the canopy to the ceiling mounting bracket using 4 screws at the top edge of the mounting bracket. Insert each screw through the canopy mounting hole and into the mounting bracket. Tighten all screws securely. (Fig.
Sutter Place Premier TM 8 9. ATTACHING THE FAN BLADES CAUTION: Remove the five rubber shipping blocks attached to the face of the motor. These blocks keep the motor from shifting during shipping and MUST be removed during installation. Step 1. Attach a blade to a blade bracket using the screws, metal washers and fiber washers provided. (Fig. 16) Make sure the blade is straight when set on the blade bracket. Tighten each mounting screw until the fiber washer is slightly compressed.
9 11. INSTALLING THE LIGHT FIXTURE 1. While holding the light fixture assembly under your ceiling fan, push the square wire connectors together. One from the fan and one from the light fixture. (Fig.18) NOTE: These connectors are color coded and will ONLY engage when the colored strips are matched (aligned). 2. Carefully push all the wires into the switch housing assembly. Switch house mounting plate Wire connector Screws Light fixture Fig.
Sutter Place Premier TM 12. OPERATING INSTRUCTIONS Turn the power on and check the operation of your ceiling fan. The "center" pull chain turns the light fixture On and Off. The "outside" pull chain controls the 3 speeds of your ceiling fan. 1 pull = High, 2 pulls = Medium, 3 pulls = Low and the 4th pull turns the motor off. The Black Slide Switch on the side of the switch housing controls the direction of the blades "Forward and Reverse". Fig.
11 13. TROUBLESHOOTING Problem Solution Fan will not start. 1. Check that all fuses or circuit breakers are installed or in the ON position. 2. Check all electrical connections to insure proper contact. CAUTION: Make sure the main power is OFF when checking any electrical connection. Fan sounds noisy. 1. Make sure all motor housing screws are snug. 2. Make sure the screws that attach the fan blade bracket to the motor hub is tight. 3.