Instructions / Assembly

22) Make wire connections (connectors not provided). Reference
chart below for correct connections and wire accordingly.
23) Raise canopy to ceiling.
24) Secure canopy in place by tightening threaded ring onto
screw collar loop.
25) Lower glass down over socket. Pass hole in glass over
socket.
26) Thread socket ring onto socket. Tighten socket ring to
secure glass in place. (DO NOT over tighten.)
1) Take one loose arm, slip hook at end of arm through loop on
fixture body.
2) Pass threaded pipe on top of arm through hole in top trim.
3) Slip lockwasher over end of threaded pipe protruding from
inside top trim. Thread hexnut onto threaded pipe. Tighten
hexnut to secure arm in place.
4) Repeat steps 1-4 for remaining loose arm.
5) Take arm with fixture wire, pass fixture wire from top of arm
through hole in top trim.
6) Pass fixture wire through hole in lockwasher. Thread
lockwasher onto end arm protruding from inside top trim.
Pass fixture wire through hole in hexnut. Thread henxut onto
end of arm. Tighten hexnut to secure arm in place.
7) Pass fixture wire through hole in top plate. Lower top trim
down. Pass threaded pipe in center of top trim through hole
in top plate.
8) Pass fixture wire through hole in coupling. Thread coupling
onto threaded pipe protruding from top plate.
9) Pass fixture wire through end of stem. Thread end of stem
into coupling.
NOTE: Thread locking compound must be applied to all
stem threads as noted with symbol (3) to prevent accidental
rotation of fixture during cleaning, relamping, etc.
10) Pass fixture wire through remaining stems and screw stems
together.
11) Thread small threaded pipe into end of small loop.
12) Pass fixture wire through end of threaded pipe on small
loop. Thread small loop onto end of last stem.
13) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
14) Take threaded pipe from parts bag and screw in screw collar
loop a minimum of 6 mm (1/4”). Lock into place with hexnut.
15) Run another hexnut down threaded pipe almost touching
first hexnut. Now screw threaded pipe into mounting strap.
Mounting strap must be positioned with extruded thread
faced into outlet box. Threaded pipe must protrude out the
back of mounting strap. Screw third hexnut onto end of
threaded pipe protruding from back of mounting strap.
16) Connect mounting strap to outlet box.
17) Unscrew the threaded ring from screw collar loop. Take
canopy and pass over screw collar loop. Approximately one
half of the screw collar loop exterior threads should be
exposed. Adjust screw collar loop by turning assembly up or
down in mounting strap. Remove canopy.
18) After desired position is found, tighten both top and bottom
hexnuts up against the bottom and top of the mounting
strap.
19) Slip canopy over screw collar loop and thread on threaded
ring. Attach chain (with fixture connected) to bottom of
screw collar loop. Unscrew threaded ring, let canopy and
threaded ring slip down.
20) Weave electrical wire and ground wire through chain links no
more than 3 inches apart. Pass wire through threaded ring,
canopy, screw collar loop, threaded pipe and into outlet box.
21) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector
(not provided.) after following the above steps. Never
connect ground wire to black or white power supply wires.
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
Date Issued: 11/20/15 IS-2345-US
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
MOUNTING STRAP
PLANCHA PARA MONTAR
SMALL LOOP
PEQUEÑA LAZO
HEXNUT
TUERCA HEXAGONAL
THREADED PIPE
TUBO ROSCADO
THREADED RING
ANILLO ROSCADO
SCREW COLLAR LOOP
OJAL DE COLLAR
ROSCADO
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
CANOPY
ESCUDETE
STEM
VASTAGO
SOCKET RING
ANILLO DEL
CASQUILLO
ARM
BRAZO
GLASS
VIDRIO
3
3
COUPLING
ACOPLAMIENTO
TOP PLATE
PLACA SUPERIOR
TOP TRIM
ADORNO SUPERIOR