60" Ahrendale LED
TABLE OF CONTENTS SAFETY RULES ………………………………………………………. 4 INSTALLING THE LIGHT KIT AND GLASS ………… 14 TOOLS REQUIRED ……………………………………………… 5 INSTALLING THE WALL CONTROL ………………… 15 PACKAGE CONTENTS …………………………………………. 5 CONTROL SYSTEM SET-UP ………………………………… 16 MOUNTING OPTIONS ………………………………………… 6 OPERATING INSTRUCTIONS ……………………………… 16 HANGING THE FAN ………………………………………....... 7 TROUBLESHOOTING………………………………………………17 INSTALLATION OF SAFETY SUPPORT ……………… 9 FCC WARNING…………………………………………………………..
SAFETY RULES 4 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 8. Do not use water or detergents when cleaning the fan or fan blades. A dry dust cloth or lightly dampened cloth will be suitable for most cleaning. 2. All wiring must be in accordance with the National Electrical Code and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 9. 3.
TOOLS REQUIRED Philips screw driver Blade screw driver 11 mm wrench Step ladder Wire cutters PACKAGE CONTENTS Unpack your fan and check the contents . You should have the following items: A. Mounting bracket M. Package hardware B. Ball / downrod assembly 1)_Mounting hardware : C. Canopy Wood screws (2) ,Flat Washers (2) , Screws D. Canopy Hole Cover (2) , Lock washers (2), Wire Connector (3) E. Coupling Cover 2) Blade attachment hardware : F. Motor Body Screws (17) , Washers (17) G.
MOUNTING OPTIONS If there isn’t an existing UL (cUL for Canadian Installation) listed mounting box, then read the following instructions. Disconnect the Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. The outlet box and its support must be able to fully support the moving weight of the fan (at least 50 lbs). Do not use plastic outlet boxes. Outlet box Fig. 1 box.
HANGING THE FAN REMEMBER to turn off the power before you begin installation. This is necessary Outlet Box for your safety and also the proper programming of the control system.To properly Ceiling Mounting Bracket install your ceiling fan, follow the steps below. Flat Washer Screw Step 1 . Before attaching fan to outlet box (not included), ensure the outlet box is Fig. 5 securely fastened to at least two points to a structural ceiling member (a loose box will cause the fan to wobble).
HANGING THE FAN Lock Pin Step 3. Loosen the two set screws and remove the lock pin and hitch pin from the top coupling of the motor body.Carefully feed the fan wires up through the downrod. Hitch Pin Set Screw Lock Pin Set Screw Thread the downrod onto the motor coupling until the hitch pin holes are aligned. Hitch Pin Motor Body Next, replace the lock pin and hitch pin, and tighten both set screws. (Fig. 7) Fig. 7 Step 4. Slip the coupling cover, canopy hole cover and canopy onto the downrod.
INSTALLATION OF SAFETY SUPPORT (required for Canadian installation ONLY) Flat Washer Wood Screw Support Brace A safety support cable is provided to help prevent the ceiling fan from faIling, please install it as follows. Step 1. Drive a wood screw and washers into the side of the brace that holds the outlet box. Leave 3mm (1/8") of space between the support brace and the washer. (Fig. 10) Step 2.Insert the safety cable through the mounting bracket and one of the holes in the outlet box into the ceiling.
MAKE THE ELECTRIC CONNECTIONS Mounting Bracket Receiver WARNING: To avoid possible electrical shock,be sure you have turned off the power at the main circuit panel before wiring. Follow the steps below to connect the fan to your household wiring. Use the wire connecting nuts supplied with your fan. Secure the connector with electrical tape. Make sure there are no loose wire stands or connections. Fig. 12 WARNING: If your house wires are different colors than referenced in this manual, stop immediately.
MAKE THE ELECTRIC CONNECTIONS Step 4. If your outlet box has a ground wire ( green or bare copper ) connect it to the fan ground wires : otherwise connect the fan ground wire to the mounting bracket. Secure the wire connection with a plastic nut provided. After connecting the wires, spread them apart so that the green and white wires are on one side of the outlet box and black and blue wires are on the other side. (Fig.
FINISHING THE INSTALLATION Shoulder Screw Step 3. Securely attach and tighten the canopy hole cover over the shoulder screws in the mounting bracket utilizing the keyslot twist-lock feature. (Fig. 16) Canopy Hole Cover Fig. 16 ATTACHING THE FAN BLADES NOTE: Before continuing , make sure the power is disconnected by turning off the circuit breaker of removing the fuse at the circuit box. Blade Screw Step 1. Position the blade over the blade arm with threaded posts showing.
ATTACHING THE FAN BLADES Motor Body Step 2. Fasten blade assembly to the holes located on the bottom of the flywheel. Tighten the two "pre- installed" motor screws in the blade arm. Repeat steps for the remaining blades assemblies.(Fig. 18) Blade Assembly Fig. 18 INSTALLING THE DECORATIVE FRAME Step 1. Remove this screw preinstalled on mounting plate and loosen the other two (do not remove). Place the two slot holes on the switch housing over the 2 screws previously loosened from the mounting plate.
INSTALLING THE LIGHT KIT AND GLASS NOTE: Before continuing installation, confirm that the power is still turned off at the main circuit breaker or by removing the correct fuse. Turning the power off using a wall switch is not sufficient to prevent electrical stock. Step 1. Remove 1 of the 3 screws from the switch housing and loosen the other 2 screws (do not remove). (Fig. 20) Switch Housing Light Kit Screw Step 2.
INSTALLING THE WALL CONTROL Outlet Box Switch All wiring must be in accordance with the National Electrical Code and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. Select a location to install your wall control. You can replace an existing wall switch, or install the wall control on ANY flat surface. Wall Plate Fig. 22 NOTE: SWITCH INSTALLATION MUST COMPLY WITH ALL LOCAL AND NATIONAL ELECTRIC CODE . Step 1.
CONTROL SYSTEM SET-UP Step 1. After installation is complete, press the LEARN button for 3 seconds within 30 seconds of AC power is turned on. Fan will turn on at medium speed and light (if installed) will turn on. This confirms that the SMART SYNC setting is active and ok. (Fig. 24) Step 2. If you cannot finish the setting within the 30 seconds time frame, the main power must be turned off and re-started again. This will repeat step 1 until the LEARN feature is activated as indicated.
TROUBLESHOOTING Problem Solution Fan will not start. 1.Check circuit fuses or breakers. 2.Check all electrical connections to insure proper contact. CAUTION: Make sure the main power is OFF when checking any electrical connection. 3.Make sure the transmitter batteries are installed properly. Positive (+) side facing out. 4.Insure the batteries have a good charge. Fan sounds noisy. 1.Make sure all motor housing screws are snug. 2.
TROUBLESHOOTING Problem Solution Remote control malfunction. 1.Ceiling Fans with remote control systems CAN NOT be operated in conjunction with any other control system EXCEPT a basic On/Off wall switch, if desired. FCC WARNING: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,and (2) this device must accept any interference received,including interference that may cause undesired operation.
60" Ahrendale LED 19