Sola 330150, 330151, 330152 A Kichler ® Select ™ ceiling fan Includes wall mount control system Kichler® Lighting 7711 East Pleasant Valley Road P.O. Box 318010 Cleveland, Ohio 44131-8010 Instruction Manual Customer Service 866.558.
1 1. SAFETY RULES 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the National Electrical Code and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 3. WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control. Use only the control provided with the fan. 4.
Sola 2. TOOLS AND MATERIALS REQUIRED Philips screw driver Blade screw driver 11 mm wrench Step ladder Wire cutters 3. PACKAGE CONTENTS Unpack your fan and check the contents .
3 4. MOUNTING OPTIONS If there isn't an existing ETL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Outlet box Fig. 1 Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. The outlet box and its support must be able to fully support the moving weight of the fan (at least 50 lbs). Do not use plastic outlet boxes.
Sola 4 5. HANGING THE FAN REMEMBER to turn off the power before you begin installation. This is necessary for your safety and also the proper programming of the control system. To properly install your ceiling fan, follow the steps below. ETL Listed Outlet Box Step 1. Pass the 120 Volt supply wires from the ceiling outlet box through the center of the mounting bracket. Securely attach the Ceiling Mounting Plate/Bracket to the ceiling junction box as shown. ( Fig.
5 6. INSTALLATION THE SAFETY SUPPORT Support Brace Flat Washer Wood Screw Spring Washer Ceiling Outlet Box Fig. 6 Safety Cable Bolt Wood Screw Fig. 7 7. MAKE THE ELECTRIC CONNECTIONS 1 2 3 4 ON DIP Code Switch Fig. 8 A safety support cable is provided to help prevent the ceiling fan from failing, please install it as follows. Step 1. Drive a wood screw and washers into the side of the brace that holds the outlet box. Leave 3mm (1/8") of space between the support brace and the washer. (Fig.
Sola 6 Step 1. Motor to Receiver Electrical Connections: Connect the BLACK wire from the fan to BLACK wire marked "TO MOTOT L" from the receiver. Connect the WHITE wire from the fan to the WHITE wire marked "TO MOTOR N" from the receiver. Connect the BLUE wire from the fan to the BLUE wire marked "FOR LIGHT" from the receiver. Secure all the wire connections with the plastic wire nuts provided. ( Fig. 9) Step 2.
7 Flywheel Blade Motor Hub Step 2. Insert the blade through the slots on the flywheel and attach to the motor hub using the blade screws and blade tirm. Make sure the screws securing the blades to the motor hub are tighten and are properly seated. (Fig. 11) Blade Trim Blade Screw Fig. 11 Step 3. Remove one of the three screws in the adapter plate at the bottom of the motor assembly and retain the screw for later use. Slightly loosen the remaining two screws.
Sola Step 5. If installing the light kit, skip to step 7. Assembly the light kit wire cover to the switch housing using the two key slots. Replace the removed screw and secure all three screws. (Fig. 14a) Switch Housing Light Kit Wire Cover Screw Fig. 14a Step 6. Assemble the steel cap to the light kit by twisting in a clockwise direction. (Fig. 14b) Steel Cap Fig. 14b Step 7.
9 9. INSTALLING THE TRANSMITTER Outlet Box Switch Wall Plate All wiring nust be in accordance with the National Electrical Code and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. Select a location to install your wall mount Control System Transmitter. You can replace an existing wall seitch, or install the transmitter to a new outlet box. NOTE: Make sure the electrical power is TURNED OFF at the main panel before continuing. Fig.
Sola Step 3. You can leave the frequency switches at the factory setting. Or you have to change the dip switch setting in the remote if you are using more than one fan in the same area and want to control them separately. Remove the battery and change the dip switch setting, assuring that they are different from the other fans. Reinstall the battery and switch plate on the control. (Fig. 19) R ON ECE Code Switch 11. OPERATING INSTRUCTIONS: Fig.
11 12. TROUBLESHOOTING Problem Solution Fan will not start. 1. Check circuit fuses or breakers. 2. Check all electrical connections to insure proper contact. CAUTION: Make sure the main power is OFF when checking any electrical connection. 3. Make sure the transmitter batteries are installed properly. Positive (+) side facing out. 4. Insure the batteries have a good charge. Fan sounds noisy. 1. Make sure all motor housing screws are snug. 2.
Sola 12 13. FCC WARNNING: This device complies with part 15 of the FCC Rules. Operation is subject to the folioeing two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifictons not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.