Installation Sheet

1) Pass fixture wire from each coupling on top of fixture
through one stem for each side and screw each stem into
each coupling. NOTE: Thread locking compound must be
applied to all stem threads as noted with symbol (3) to
prevent accidental rotation of fixture during cleaning,
relamping, etc.
2) Pass fixture wire through remaining stems and screw stems
together.
3) Thread one small threaded pipe into end of each small loop.
4) Pass fixture wire through first loop. Thread one first loop
onto end of each last stem.
5) Attach one chain link to each small loop at end of each
stem. Then attach each chain link to one second small loop.
6) From each stem, pass fixture wire through each second
loop. Then from each second loop, pass fixture wire through
each hole in top plate.
7) From each stem, pass fixture wire through each hole in
canopy. Then pass threaded pipe at end of each second
loop through each hole in canopy.
8) On one side, pass fixture wire from threaded pipe protruding
from inside canopy through hole in one lockwasher. Thread
lockwasher onto end of threaded pipe.
9) From the same side as step 8, pass fixture wire through hole
in hexnut. Thread hexnut onto end of threaded pipe.
10) On other side of fixture, pass fixture wire through loop on
end of safety cable. Slip loop on safety cable over end of
threaded pipe protruding from inside of canopy.
11) From the same side as step 10, pass fixture wire through
hole in lockwasher. Thread lockwasher onto end of threaded
pipe protruding from inside canopy.
12) Pass fixture wire through hole in hexnut. Thread hexnut onto
end of threaded pipe.
13) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
14) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
15) Attach mounting strap to outlet box. (Screws not provided).
Mounting strap can be adjusted to suit position of fixture.
MOUNTING STRAP
ABRAZADERA DE MONTAJE
CANOPY
ESCUDETE
Date Issued: 9/4/15 IS-43362-US
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
KNURL KNOB
PERILLA ESTRADA
SMALL LOOP
ARGOLLA
PEQUEÑA
CHAIN LINK
ESLABÓN DE CADENA
STEM
VASTAGO
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
16) Attach safety cable to slot in mounting strap
17) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector
(not provided.) after following the above steps. Never
connect ground wire to black or white power supply wires.
18) Make wire connections (connectors not provided). Reference
chart below for correct connections and wire accordingly.
19) Push fixture to ceiling, carefully passing mounting screws
through holes in canopy.
20) Thread knurl knobs onto mounting screws. Tighten knurl
knobs to secure fixture to ceiling.
21) Lower one bobeche over end of each candle cover.
HEXNUT
TUERCA HEXAGONAL
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
LOCKWASHER
ARANDELA DE SEGURIDAD
3
3
3
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
SAFETY CABLE
ACTIVACIÓN DE SEGURIDAD
LOCKWASHER
ARANDELA DE SEGURIDAD
HEXNUT
TUERCA HEXAGONAL
TOP PLATE
PLACA SUPERIOR
BOBECHE
PLATO DE VELA
CANDLE COVER
TUBO DE LA VELA