Installation Sheet

Date Issued: 09/25/17 IS-44160LED-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starting and during the installation.
WARNING:
This xture is intended for installation in accordance with the
National Electrical Code (NEC) and all local code specications.
If you are not familiar with code requirements, installation by a
certied electrician is recommended.
FCC INFORMATION:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following mea-
sures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Instructions
1) Pass electrical and ground wire through the desired amount of
stems[1], chain links[2], and loops[3] and screw together with
supplied nipples[4].
2) Using the two (2) strap mounting screws[5], attach the mount-
ing strap to the outlet box.
3) Screw threaded pipe into mounting strap. Mounting strap must
be positioned with extruded thread facing into the outlet box.
Threaded pipe must protrude out of the back of the mounting
strap.
4) Install one (1) hexnut under the mounting strap and one (1)
on top of the mounting strap on the threaded pipe; this will
secure the threaded pipe in place. Place third hexnut onto the
threaded pipe.
5) Connect four (4) loops, two (2) chain links with four (4) thread-
ed nipples and inspection cable[6] to the canopy [7].
6) Install 6 glass plates[8] using the (24) washers[9] and (24)
knobs [10] as shown.
7) Screw on the glass mounting plate[11] with (12) screws.
8) Place glass assembly into place utilizing the four(4) hooks[12]
and connecting to the xture[13].
9) Grounding instructions: (See Illus. A or B).
A) On xtures where mounting strap is provided with a hole
and two raised dimples. Wrap ground wire from outlet box
around green ground screw, and thread into hole.
B) On xtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If xture is provided with ground wire. Connect xture ground
wire to outlet box ground wire with wire connector. (Not pro-
vided.) After following the above steps. Never connect ground
wire to black or white power supply wires.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
A
B
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
1
2
3
4
5
6
7
9
10
8
11
12
13
10) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.