Installation Sheet
Table Of Contents
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
IS-44239-US
1) Pass xture wire from the coupling on top of xture[M]
through a stem[A] and threaded tubes[B] and screw
stem into coupling. NOTE: Thread locking compound
must be applied to all stem threads as noted with symbol
(4) to prevent accidental rotaon of xture during
cleaning, relamping, etc.
2) Pass xture wire through desired amount of stems and
screw stems together using supplied short threaded
tubes[B].
3) Pass xture wire from last stem through rst loop[H].
Thread rst loop onto end of last stem.
4) Pass xture wire through second loop[H] and through
hole in canopy[D]. (If second loop is already aached to
canopy, proceed to step 6).
5) Pass threaded pipe at end of second loop through hole
in canopy. Thread lockwasher[C] onto threaded pipe
protruding from inside canopy. Pass xture wire through
hole in hexnut and thread hexnut[K] onto end of
threaded pipe.
6) Aach chain link[I] to small loop at end of stem and to
loop on canopy.
7) Find the appropriate threaded holes on mounng
strap[G]. Assemble mounng screws[J] into threaded
holes.
8) Aach mounng strap to outlet box[F]. The mounng
strap can be adjusted to suit posion of xture using the
strap mounng screws[E].
9) Grounding instrucons: (See Illus. A or B).
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is provided,
aach ground wire from outlet box under cupped
washer and green ground screw, and thread into
mounng strap.
If xture is provided with ground wire. Connect xture
ground wire to outlet box ground wire with wire connector.
Aer following the above steps. Never con¬nect ground wire
to black or white power supply wires.
10) Make wire connecons. Reference chart below for
correct connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.)
Neutral Wire
11) Push xture to ceiling, carefully passing mounng screws
through holes in canopy . NOTE: Be certain wires do not
get pinched between canopy and ceiling.
12) Use ball knobs[N] and lockwashers[L] to secure canopy.
Tighten to secure.
13) Insert recommended bulb[P] (Not supplied).
14) Lower the glass shades[O] down over the installed bulbs.
Fixture Diagram
Parts List
Cauons
Installaon Instrucons
[A] Stem
[B] Threaded
Tube
[C] Lockwasher
[D] Canopy
[E] Strap
Mounting
Screws
[F] Outlet Box
[G] Mounting
Strap
[H] Loop
[I] Chain Link
[J] Mounting
Screws
[K] Hexnut
[L] Lockwashers
[M] Coupler
[N] Ball Knobs
[O] Glass Shades
[P] Bulb
F
G
E
D
H
A
B
K
J
I
M
►
►
C
N
L
O
P
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance with
the Naonal Electrical Code (NEC) and all local codes. If you
are not familiar with code requirements, installaon by a
cered electrician is recommended.