Installation Sheet

IS-44315-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
7) Connect mounng strap[G] to outlet box using strap
mounng screws[L]
8) Unscrew the threaded ring from screw collar loop. Take
canopy[I] and pass over screw collar loop. Approximately
one half of the screw collar loop exterior threads should
be exposed. Adjust screw collar loop by turning assembly
up or down in mounng strap. Remove canopy.
9) Aer desired posion is found, ghten both top and
boom hexnuts up against the boom and top of the
mounng strap.
10) Slip canopy over screw collar loop and thread on
threaded ring. Aach chain link[J] (with xture
connected) to boom of screw collar loop. Unscrew
threaded ring[K], let canopy and threaded ring slip
down. (Close chain link ends together using chain pliers
or padded pliers to prevent damage to nish.)
11) Aach open chain link[J] to small loop at end of each
stem and to each loop on canopy and close the open
chain link by threading the nut down onto the link end.
12) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is provided,
aach ground wire from outlet box under cupped
washer and green ground screw, then thread into
mounng strap.
If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire
connector (Not provided) aer following the above steps.
Never connect ground wire to black or white power
supply wires.
13) Make wire connecon. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.)
Neutral Wire
14) Thread on the top loop onto the main body.
15) Raise canopy to ceiling.
16) Secure canopy in place by ghtening threaded ring onto
screw collar loop.
17) Lower the glass shades[N] onto each socket as shown.
Note that there are two (2) dierent sizes of the glass
shades.
18) Install the recommended bulbs (Not supplied).
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
[A] Coupling
[B] Stem
[C] Threaded
Tubes
[D] First loop
[E] Second Loop
[F] Hexnut
[G] Mounting
Strap
[H] Outlet Box
[I] Canopy
[J] Chain Link
[K] Threaded
Ring
[L] Strap
Mounting
Screws
[M] Screw Collar
Loop
[N] Glass Shades
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Installaon Instrucons
Installaon Instrucons (connued)
1) Pass xture wire from the coupling[A] on top of xture
through a stem[B] and threaded tubes[C] and screw
stem into coupling. NOTE: Thread locking compound
must be applied to all stem threads as noted with (4)
symbol to prevent accidental rotaon of xture during
cleaning, relamping, etc.
2) Pass xture wire through desired amount of stems and
screw stems together using supplied short threaded
tubes.
3) Pass xture wire from last stem through rst loop[D].
Thread rst loop onto end of last stem.
4) Pass xture wire through second loop[E] and through
hole in canopy[I].
5) Take threaded pipe from parts bag and screw in screw
collar loop[M] a minimum of 6 mm (1/4”). Lock into place
with hexnut[F].
6) Run another hexnut down threaded pipe almost touching
rst hexnut. Now screw threaded pipe into mounng
strap[G]. Mounng strap must be posioned with
extruded thread faced into outlet box[H]. Threaded pipe
must protrude out the back of mounng strap. Screw
third hexnut onto end of threaded pipe protruding from
back of mounng strap.
H
G
F
L
N
I
M
K
J
►
D
B
C
►
►
►
A
N
E