Owner's Manual

2 3
The Kicker KMS67 high-effi ciency component system is specially designed for “Livin’ Loud” out in
the harsh marine environment, and is made using advanced materials and construction techniques,
maintaining optimal performance for years to come. The KMS67 features a pair of 6.75 inch mid-bass
woofers and 1.7 inch horn-loaded compression drivers. Combine the KMS67 and KM67S for a 6-driver
system.
SPECIFICATIONS
WIRING & INSTALLATION
Wire and install the KMS67 drivers and horns to your speaker
cans as per the manufacturer’s instructions. For optimal
performance, consider loosely fi lling 50%-100% of the can
with poly-fi l.
Wire the cans in parallel as illustrated at the top of Page 3.
If you’ve added an additional mid to each channel with the
KM67S, please reference the diagram at the bottom of page
3.
To get the best performance with minimal distortion out of your
KM system, use a high-pass fi lter (or crossover); 80–100Hz is
a good starting point.
CROSSOVER
The KMS67 uses a built-in crossover for both the mid and horn. To adjust the output level, use the jumper
on the back of the horn-loaded compression driver by pushing down on the terminal, inserting the wire
and then releasing the terminal to secure it. For example, when using the KMS67 with extra mids provided
in the KM67S, move the jumper wire to +6 dB.
KMS Component System
Owner’s Manual
Authorized KICKER Dealer:
Purchase Date:
Speaker Serial Number:
KM67S | KMS67Models:
Note: Kicker Marine speakers meet or exceed industry standards for environmental humidity and corrosion, and for
material degradation due to UV exposure.
From Amplifi er
From Amplifi er
0 dB gives a fl at frequency
response and is the recommended
confi guration for use with one mid.
+6 dB gives a fl at frequency
response and is the recommended
confi guration for use with two mids.
Jumper Wire
Horn Can Mid Can
Mid Can Horn Can
Mid Can
Terminal Terminal
TerminalTerminalTerminal
+
+
-
-
Horn-loaded compression driver
+
+
-
-
Model: KMS67 KM67S*
Woofer [in, mm] 6-3/4, 165 6-3/4, 165
Horn Loaded Compression Driver [in,mm] 1.7, 43 N/A
Horn Exit Tractrix 60°-V x 90°-H N/A
Dome Material Titanium N/A
Rated Impedance [Ω] 4 4
Peak Power Handling [ Watts] 400 200
Continuous Power Handling [Watts RMS] 200 100
Sensitivity [1W, 1m] 94.5dB 1 mid, 99.5dB 2 mids 90.5dB
Frequency Response [Hz] 50–22k 50-1700
Woofer Mounting Hole Diameter [in, mm] 5-11/16, 144 5-11/16, 144
Woofer Bottom Mount Depth [in, mm] 3-7/8, 99 3-7/8, 99
Horn Mounting Hole Diameter [in,mm] 5-11/16, 144 N/A
Horn Mounting Depth [in,mm] 7-3/16, 183 N/A
High Pass [dB], at Frequency [Hz] 18, 1700 N/A
Low Pass [dB], at Frequency [Hz] 12, 1700 12, 1700
High Frequency Output Attenuation [dB] 0, +6 N/A
*- Available through KICKER warranty
2014 KMS Rev E.indd 2-32014 KMS Rev E.indd 2-3 8/29/2013 2:07:22 PM8/29/2013 2:07:22 PM