Specifications

Wall HeaterPAW Series
Contractor shall supply and install PAW Series in-wall forced-air electric heaters manufactured by King Electrical Mfg. Company,
of the wattage and voltage as indicated on the plans.
Ratings: Heaters shall be available in wattages of 250 to 2,250
at 120, 208, 240, or 277 Volts.
Blower and Motor: A whisper quiet tangential blower, delivering 75
CFM, shall be driven by a shaded pole, permanently lubricated, C-frame
type motor with impedance protection and sealed bearings. Motors shall
be the same voltage as the heater.
Elements: Element assemblies shall consist of three steel sheathed
heating tubes in a furnace-brazed, plate-finned, block design. Each
sheathed tube shall contain coiled Ni-Chrome wire embedded in an
insulator of Magnesium Oxide. The element assembly shall provide up to
seven (7) possible wattage configurations available for selection during
field installation. The use of external resistors, diodes, or other weak links
to obtain multiple wattages will not be acceptable.
Thermal Overload: Heaters shall be equipped with King’s patented
thermal overload Smart Limit Protection
®, which disconnects elements
and motor in the event normal operating temperatures are exceeded.
If thermal overload trips due to abnormal operating temperatures, thermal
overload shall remain open until manually reset by turning the heater off
for 15 minutes. Automatic reset of thermal overloads, which allow the
element to continue to cycle under abnormal conditions, will not be
accepted.
Grill: The grill shall be a louvered, one-piece design with rounded edges
on all four sides, with rounded corners to prevent snags from contact with
other materials. The grill shall be epoxy powder-coated in white or
almond.
Wall Can: The wall can shall be 20 gauge electro-galvanized steel and
shall contain a minimum of three (3) knockouts. The wall can shall have
a depth gauge indicator, and a factory installed, insulated and stranded
copper ground-wire. Minimum 4”clearance to floors and 6”sidewalls.
Zero clearance to combustibles in the wall.
Approvals: cULus (E41422)
Engineering Specifications
Dimensional Data
Factory Installed Options
MODEL UPC DESCRIPTION SHIP WEIGHT lbs
TKIT-1BW 20654 Built-in Single Pole Single Throw Thermostat Kit, Bright White 0.5
TKIT-2BW 20655 Built-in Double Pole Single Throw Thermostat Kit, Bright White 0.5
TKIT-1A 11058 Built-in Single Pole Single Throw Thermostat Kit, Almond 0.5
TKIT-2A 11059 Built-in Double Pole Single Throw Thermostat Kit, Almond 0.5
PAW-GUARD 16550 PAW Accessory Wire Guard 2.0
DS15 13824 Disconnect Switch, Field Installed Kit (10A/ 240V / 15A/120V) 0.5
Accessories
STEP 2: Order Wall Can
MODEL UPC DESCRIPTION SHIP WEIGHT lbs
PAWIC 00515 Recess Wall Can 2.5
PAWIC-RF 14033 Recess Wall Can - Right Hand Feed 2.5
PAWF 16319 Recess Can with Flange (remodel) 2.0
PAWS-W 16305 PIC-A-WATT® Surface Can - White - 13.5” L x 4.5” W x 7.5” H 5.5
PAWS-A 19298 PIC-A-WATT® Surface Can - Almond - 13.5” L x 4.5” W x 7.5” H 5.5
PAWS-SS 16317 PIC-A-WATT® Surface Can - Stainless Steel- 13.5” L x 4.5” W x 7.5” H 5.5
STEP 3: Order Grill (not required for -I models)
MODEL UPC DESCRIPTION SHIP WEIGHT lbs
PAWG-W 16304 Grill - White 1.0
PAWG-ALMOND 16335 Grill - Almond 1.0
PAWG-SS 16330 Grill - Stainless Steel 1.0
PAWOG-A 00555 13" H x 13.5" W x .5" D Retrofit Grill 3.0
PAWOG-B 00560 8.5" H x 17" W x .5" D Retrofit Grill 3.0
NOTE: This is the quickest option when the factory installed heaters options are not in stock.
6