Installation Guide

ManualsBrandsKingspan Insulation ManualsFoam Board Insulation100000050515

First Revision July 2016

Insulation

INSTALLATION GUIDELINES

XPS Insulation Board

Product

Kingspan GreenGuard

XPS Insulation Board comprises closed–

cell extruded polystyrene (XPS) with high water resistance and R–

value of 5.0 per inch of thickness. It is available as Type IV in square

edge board, ship–lap edge board and a score board and Type VI in

square edge or drainage channels.

1. Kingspan GreenGuard

XPS Insulation Board CM

(square edges 1/2 – 3 in., Type IV and 2-3 in., Type VI);

2. Kingspan GreenGuard

XPS Insulation Board SB

(scored board: 1-2 in., Type IV);

3. Kingspan GreenGuard

XPS Insulation Board DC

(drainage channels, 2 in., Type VI);

4. Kingspan GreenGuard

XPS Insulation Board SL

(shiplap edges, ½ - 2 in., Type IV); and

5. Kingspan GreenGuard

SLX Sheathing (lm-faced,

shiplap edges, ½ - 1 in., Type IV);

Compliance

The installer is responsible for ensuring that the installation is

in compliance with building code requirements. The code may

have requirements for specic insulation thickness or R-value and

materials along with specic thermal or ignition barriers.

All assemblies should be evaluated for effectiveness and location

of vapor retarders to avoid condensation and subsequent damage

to the structures (ASHRAE Handbook of Fundamentals). Since

foam sheathings are non-structural, they must be installed over

adequately braced framing in accordance with local building codes.

Intertek CCRR 1021;

CA BEARHFTI Lic. No. TB 1334;

Florida Product Approval – No. FL14164;

CCMC 12722-L;

MN Dept. of Energy – Chapter 7640;

FM Approvals - see RoofNav Roof System Listings;

Miami-Dade County, FL - NOA No. 12-0629.04;

UL LLC

– See Classication Certicate A183.

General

These instructions are intended for use by any individual, whether

an experienced installer or homeowner. They are general guidelines

and do not cover all aspects of insulation installation and use. As

the installer, you have sole responsibility for proper installation of all

materials. You are responsible for adhering to label instructions and

using proper safety precautions during installation.

The installation information provided describes some

common applications and represents current industry

practice. This information is intended to be used as a guide.

For information regarding other applications and more

detailed product information go to

www.kingspaninsulation.us.

Alternate installation details may be used if approved in

writing by Kingspan Insulation LLC prior to installation.

Personal Protective Equipment

For safe handling, it is recommended that you use OSHA-approved

safety glasses, work gloves, and a NIOSH or MSHA approved

disposable dust respirator. There is no requirement for re-entry or

occupancy times.

Required Tools

For all Kingspan GreenGuard

XPS Insulation Board installations,

one or more of the following tools will be required:

1. Tape measure

2. Straightedge

3. Utility knife

4. Nail gun

5. Caulk gun

6. Cordless drill

7. Hammer

8. Saw

Summary of content (6 pages)

PAGE 1
Insula t i o n First Revision July 2016 XPS Insulation Board INSTALLATION GUIDELINES Product Kingspan GreenGuard® XPS Insulation Board comprises closed– cell extruded polystyrene (XPS) with high water resistance and R– value of 5.0 per inch of thickness. It is available as Type IV in square edge board, ship–lap edge board and a score board and Type VI in square edge or drainage channels. 1. Kingspan GreenGuard® XPS Insulation Board CM (square edges 1/2 – 3 in., Type IV and 2-3 in., Type VI); 2.
PAGE 2
Insulation Board Auxiliary Materials Examination Specify auxiliary materials as shown below or other alternative approved materials: 1. Kingspan GreenGuard® Standard Seam Tape and / or Custom Seam Tape 2. Kingspan GreenGuard® Butyl Flashing and / or Kingspan GreenGuard® SuperStetch™ Butyl Flashing; 3. Adhesives, Sealants and Primers that are compatible with Kingspan GreenGuard® Extruded Polystyrene Insulation Board 4. Kingspan GreenGuard® Building Wraps for air-sealing wall installations. 1.
PAGE 3
Insulation Board Installation - Below-Grade, Perimeter Foundation Insulation Installation - Below-Grade, Slab-OnGrade Insulation In order to achieve full thermal performance, boards should be butted securely and, where plumbing, electrical or other penetrations exist, the board should be cut to fit tightly around the penetration. Use caulk, sealant or spray foam to seal around penetrations.
PAGE 4
Insulation Board Installation - Exterior Cavity Wall Insulation In order to achieve full thermal performance, boards should be butted securely and, where plumbing, electrical or other wall penetrations exist, the board should be cut to fit tightly around the penetration. Use caulk, sealant or spray foam to seal around penetrations. 1. Install insulation board against the masonry wall by friction, fitting boards between masonry wall ties, or using an adhesive.
PAGE 5
Insulation Board Installation- Exterior Continuous Insulation, Air Sealing and Weather-Resistive Barrier Fastener Types Chart Application Fastener Type Wood Stud Annular thread with 1 in. plastic cap nail or common galvanized roofing nails. Steel Stud Fastener Length Long enough to extend into the framing a minimum of 3/4 in.
PAGE 6
For more information on specific building product recommendations and installation guidelines, contact your Kingspan Insulation LLC representative. For the most current product and compliance information go to www.kingspaninsulation.us. Kingspan Insulation LLC believes the information and recommendations herein to be accurate and reliable.