| Table of Contents FOOD PROCESSOR SAFETY Important Safeguards . Dialectical Requirements. Po ti Models... Electrical Requirements-Metal Models PARTS AND FEATURES. ACCESSORIES In chided Accessories... Disc Assembly Overview. Necessaries Selection Guido PREPARING THE FOOD PROCESSOR FOR FIRST USE Before First Use. Removing the Work Bow! Cover from the Work Bow! Storing Parts SETTING UP YOUR FOOD PROCESSOR Attaching the Work Bow. Attaching the Work Bowl Cover Installing the Adjustable Shying Disc .
FOOD PROCESSOR SAFETY Your safety and the safety of others are very important. Wa have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING. These words mean: Ye be killed lousy injured cont immediately Soon instructions.
FOOD PROCESSOR SAFETY 7. Dao not operate any appliance with a damaged cord or plug, or after the appliance malfunctions, or is dropped or damaged in any manner. Return appliance to the nearest Authorized Service Facility for examination, repair, or electrical or mechanical adjustment, in order to avoid a hazard. 8. The use of attachments not recommended or sold by Kitchen Aid may cause fire, electric shock, or injury. 9. Do not use outdoors. 10. Do not let cord hang over edge of table or counter. II.
FOOD PROCESSOR SAFETY Electrical Requirements Plastic Models [7H Fire Hazard Da not use an extension cord, Doing so can result In death or fire. Vols: 220-240 Vols VAC Hertz: 50/60 Hz NOTE: This Food Processor is equipped with a polarized plug (ane blade is wider than the other}. To reduce the risk of electrical shock, this plug will fit in a polarized outlet only one way, If the plug does not fit fully in the outlet, reverse the plug. I it still does not fic, contact a qualified electrician.
PARTS AND FEATURES — Julienne Disc {select models only) wy — Reversible 2 rn and 4 mm) Shredding Disc Externally = Adjustable St icing Disc Thin to Thick Chef's accessory Case Disc Shining Drive Adapter Adapter Adapter 3 Piece Food Pusher Work Bow! s Cover with vino-| Feed Tube 945 mi (4-Cup}) Mini-Bart and Mini-Blade Stainless Steel Multipurpose Blade Work Bowl Externally Adjustable A.
PARTS AND FEATURES Important parts and accessories included with your new Food Processor are highlighted below, Refer to the following pages for additional details on accessories included with your Food Processor as well as optional accessories you car order separately (some optional accessories included with select models).
Disc Assembly Overview There are two different disc adapters included with the food processor, Ore fs used exclusively with the adjustable slicing disc. The other is used with all other discs.
ACCESSORIES Accessories selection guide Not all accessories shown ave included with al models. Cato rT Food Fle ET .
WARNING Cut Hazard Handle blades carefully. Failure to do so can result in cuts. Before First Use Before using your Food Processor for the first time, wash the work bowl, work bowl cover, mini-bow, feed tube pushers, discs. and blades either by hand or in the dishwasher (see “Cleaning the Food Processor”). Removing the Work Bowl Cover from the Work Bowl Your Food Processor is shipped with the work bowl cover installed on the work bowl, with the mini-bowl inside the work bowl.
SETTING UP YOUR FOOD PROCESSOR Attaching the Work Bowl 1. Place the Food Processor on a dry, level counter top with the controls facing forward, Da not plug in the Food Processor until it is completely assembled. 2, Place the work bowl on the base, aligning the raised portion with the indentation on the base. The center hole should fit over the power shaft. 3. Grasp the work bow! handle and wn the bowl counterclockwise to lock it on the base.
Installing the Adjustable Slicing Disc IMPORTANT: The adjustable slicing disc can only be installed in one direction. E. With the work bowl installed, place the drive adapter an the power shaft of the base. 2. Holding the adjustable slicing disc by the 2 finger grips, align the pins onto the adjustable slicing disc adapter into the Los lots on the disc.
SETTING UP YOUR FOOD PROCESSOR Installing Other Slicing or 3. With the work bow! installed, slide the Shredding Discs drive adapter onto the power shaft. : TEP: You may need to turn the disc/drive, IMPORTANT: The optional julienne and adapter until it drops down into place plane/shave discs can only be installed in one direction, When using the reversible shredding disc, have the desired side {daffiness) facing UR Ee 1.
SETTING UP YOUR FOOD PROCESSOR installing the Mini-Bowl and Installing the Multipurpose Blade or Dough Blade IMPORTANT: The multipurpose blade and dough blade can only be used with the work bowl. 1. Place the blade on the power shaft. 2. Rotate the blade so it falls anti place on the power shaft. Mini-Blade 1. Place the mini-bowl inside the work bowl over the power shaft. Rotate the minibar until the tabs on the top edge of the baw drops into the indents on the top of the work howl NN ¥ 3.
SETTING UP YOUR FOOD PROCESSOR Using the 3-in-1 Feed Tube “The 3-in-| feed tube features a 3-piece food pusher. Use the entire food pusher to process large items, or use the inner portions to create medium-sized or small feed tubes to process smaller items.
A WARNING = Rotating Blade Hazard Always use food pusher. Keep fingers out of openings. Keep away from children. Failure to do so can result in amputation or cuts, Before Use Before operating the Food Processor, be sure the work bow, blades, and quark bowl cover are properly assembled on the Food Processor base (see “Setting Up Your Food Processor”). Maximum Liquid Level This line on the work bowl indicates the maximum level of liquid that can be processed by the Food Processor.
USING YOUR FOOD PROCESSOR Removing Processed Foods 5. If using the mini-bowl, grasp and remove the bawl using the finger grips located WARNING along the top edge of the bow. Cut Hazard Handle blades carefully, Ee Failure to do so can result in cuts. 1. Press the “0” (OFF) Button, 2. Unplug the Food Processor before disassembling, 3. Turn the work bowl cover 0 the left and remove, 6. Turn the work bowl to the left to unlock it from the base. Lift to remove Ty 4.
Lo mnt ee WARNING Cut Hazard Handle blades carefully. Failure to do so can result in cuts, I. Press the Button. 2. Unplug the Food Processor before Cleaning. Wipe the base and cord with a warm, sudsy cloth, and wipe clean with a damp cloth. Dry with a soft cloth, Do net use abrasive cleansers or scouring pads. . Please note these BAP-free bowls require special handling. If you choose to use a dishwasher instead of hand washing, please follow these guidelines.
Ele coat hE a To finely chop citrus peel: With sharp knife, peel colored portion {without white membrane} from citrus. Cut peel in small strips. Process until finely chopped. To mince garlic or to chop fresh herbs or small quantities of vegetables: With processor running, add food through the feed tube. Process until chopped. For best results, make sure quark bow and herbs are very dry before chopping.
To slice or shred fruits and vegetables that ave small, such as strawberries, mushrooms, and radishes: Position food vertically or horizontally in layers within the feed tbe. Fill feed tube in order to keep food positioned properly Process, using even pressure.
11PS FOR GREAT RESULTS * To capitalize on the speed of the processor, drop ingredients to be chopped through the feed tube while the processor is running. Different foods require varying degrees of pressure for best shredding and slicing results.
TROUBLESHOOTING If your Food Processor should malfunction or fail to operate, check the following: Food Processor doesn’t rum: * Make sure that the bowl and lid are properly aligned and locked in place and the large food pusher is inserted in the feed whe When using the large feed tbe opening, make sure that feed is not above the Max Fill line on the feed tube.