KHPF 9010 KHPS 9010
Product description and symbols 4 Using the burners 4 Practical advice on using the hob 5 Positioning the pan supports and wok support 5 Hood and cabinetry clearances (mm) 6 Injector table 6 Warnings and suggestions 7 Safeguarding the environment 8 Installation (Flush and Traditional fitting) 9 Gas connection 9 Electrical connection 10 Fixing the hob to the work top. Traditionally fitted model 10 Fixing the hob to the work top.
Product description and symbols 1. Removable pan supports 2. 1 kWh auxiliary burner 3. 1.65 kWh semi-fast burner 4. 3 kWh fast burner 5. 1.65 kWh semi-fast burner 6. Professional wok burner 7. Auxiliary burner control knob 8. Semi-fast burner control knob 9. Fast burner control knob 10. Semi-fast burner control knob 11.
Practical advice on using the hob Read the instructions to get the best out of your hob. • Use pans with a similar diameter to the burner (see the table on this page). • Use flat bottomed pans except with the wok support. • Do not use excessive water when cooking foods and use the lid. • Ensure that pans are fully supported by the pan supports and do not protrude over the edges. Important: Do not rest or drag the pan supports upside down on the hob as this could scratch it.
Hood and cabinetry clearances (mm) If a hood is to be installed above the hob, refer to the hood installation instructions to ensure the correct height above the hob. Injector table Category II2H3+ Type of gas used Type of burner Injector label Control primary air (X)(mm) Nominal heat flow kW Nominal Reduced consumption heat flow kW min. nom. max.
Warnings and suggestions To get the most out of your hob, please read the instructions carefully and keep them for future consultation. • These instructions are only valid in the countries whose destination symbol is shown on the serial number plate on the hob. • The packing (plastic bags, expanded polyurethane, etc) pose a potential threat to children and should be disposed of carefully.
Safeguarding the environment Packing The packing material is 100% recyclable and is labelled with the recycling symbol . Please dispose of all packing responsibly and carefully. Note: • Incorrect placement of the pan supports can scratch the hob. To avoid this, always ensure that the rubber feet on the bottom of the pan supports are the only part of the pan supports that touch the hob. Do not drag the pan supports across the hob surface. • Do not use two burners to cook 1 pan.
Installation (Flush and Traditional fitting) Technical information for the installer • This appliance can be installed into a 20mm 50mm thick worktop. • If no oven is to be installed below the hob, a panel must be fitted under the hob to prevent hob damage and protect the cupboard contents.
Electrical connection The electrical connections must comply with current legislation and be carried out by a qualified, competent person. • Information on the voltage and power absorbed are shown on the serial no. plate. • The appliance must be earthed. • When installing the appliance, we recommend that this hob is protected by a 3mm bi-polar switch. • If damaged, the power cable must be replaced with an identical type of powercable ( H05V2V2-FT90ºC, or H05RR-F type).
Fixing the hob to the work top. Flush fitted model Important: The following procedure must be carried out by competent technical personnel only. The hob can be installed on, or into different types of materials, such as masonry, metal, wood and heat resistant laminate coated wood (90°C). ≥ 2,2 1,2 51 0 80 861 848 49 8 51 1 Cut an opening in the worktop to the dimensions shown in the diagram. 860 R.
Adaption to a different type of gas supply If you are using a different kind of gas from the one indicated on the serial no. plate and the orange label on the back of the hob, you must replace the injectors; in the case of the Wok burner, adjust the primary air (see Injector table on page 6). The orange label should be removed and kept together with the manual.
Fitting the wok burner To fit the double crown wok burner: Insert in the following order: 1. burner ring (A); 2. decorative covering ring (B); 3. external burner cap (C); 4. internal burner cap (D). Note: make sure that: 1. the locating pin for the burner ring (A) is inserted correctly in the slot on the burner unit. 2. that the locating pin on the external burner cap (C) is inserted in the slot on the burner ring (A).
General cleaning & maintenance Always disconnect the hob from the electrical power supply and wait until it cools before cleaning and/or doing maintenance work. In order to keep your hob in good condition, you must keep it clean, removing any food residue each time you use it. Cleaning the hob surface: o the stainless steel surface may become stained if it comes into contact with hard water over along period of time or with extremely strong, aggressive cleaning products.
Troubleshooting guide If the hob is not working properly, work through this guide before contacting our Customer Care Centre. 3. the end part of the thermocouple is clean. The pans are not stable? Check that: 1. the bottom of the pan is perfectly flat. 2. the pan is centred on the burner. 3. the pan supports are correctly positioned with all the rubber feet in place. The burner does not ignite, or the flame is unsteady? Check that: 1.
Printed in Italy 02/07 5019 719 01135 n GB
