Dimensions Guide

ManualsBrandsKitchenAid ManualsFreezer18 in. 50 lb. Freestanding or Built-In Icemaker in Black

Ice Maker

PRODUCT MODEL NUMBER

Electrical: A 115 Volt, 60 Hz., AC only, 15- or 20-amp electrical supply, properly

grounded in accordance with the National Electrical Code and local codes and

ordinances, is required.

It is recommended that a separate circuit, serving only your ice maker, be provided. Use

a receptacle which cannot be turned off by a switch or pull chain.

IMPORTANT: If this product is connected to a GFCI (Ground Fault Circuit Interrupter)

equipped outlet, nuisance tripping of the power supply may occur, resulting in loss of

cooling. Ice quality may be affected. If nuisance tripping has occurred, and if the

condition of the ice appears poor, dispose of it.

Water: A cold water supply with water pressure between 30 and 120 psi (207 and

827 kPa) is required to operate ice maker. If you have questions about your water

pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply:

■

A reverse osmosis system is not recommended for ice makers that have a drain pump

installed.

■

For gravity drain systems only.

■

The pressure of the water coming out of a reverse osmosis system going to the water

inlet valve of the ice maker needs to be between 30 and 120 psi (207 and 827 kPa).

Location:

■

To ensure proper ventilation for your ice maker, the front side must be completely

unobstructed. The ice maker may be closed-in on the top and three sides, but the

installation should allow the ice maker to be pulled forward for servicing if necessary.

■

Installation of the ice maker requires a cold water supply inlet of

⁄4" (6.35 mm) OD soft

copper tubing with a shutoff valve or a Whirlpool supply line Part Number 8212547RB,

and a Whirlpool approved drain pump, Part Number 1901A, only to carry the water to

an existing drain.

■

Choose a well ventilated area with temperatures above 55°F (13°C) and below 110°F

(43°C). Best results are obtained between 70°F and 90°F (21°C and 32°C).

■

The ice maker must be installed in an area sheltered from the elements, such as wind,

rain, water spray, or drip.

■

When installing the ice maker under a counter, follow the recommended opening

dimensions shown. Place electrical and plumbing fixtures in the recommended

location as shown.

CABINET OPENING DIMENSIONS

■ Check that the power supply cord is not damaged, or pinched or kinked

between the ice maker and the cabinet.

■ Check that the water supply line is not damaged, or pinched or kinked

between the ice maker and the cabinet.

■ Check that the drain line (on some models) is not damaged, or pinched

or kinked between the ice maker and the cabinet.

■ Choose a location where the floor is even. It is important for the ice

maker to be level in order to work properly. If needed, you can adjust

the height of the ice maker by changing the height of the leveling legs.

KUIC18NNZ

KUIC18PHZ

KUIS18NNZ

KUIS18PNZ

Because Whirlpool Corporation policy includes a continuous commitment to improve

our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation

Instructions packed with product. Specifications subject to change without notice.

Ref. W10515677A

4/8/13

14¹⁄₂"

(36.8 cm)

18"

(45.7 cm)

24"

(60.1 cm)

(22.9 cm)

28¹⁄₂"

(72.4 cm)

34"

(86.4 cm)

Min.

¹⁄₂"

(87.6 cm)

Max.

3¹⁄₂"

(8.9 cm)

1⁷⁄₈"

(4.8 cm)

23"

(58.4 cm)

2" - 1¹⁄₂"

(5 cm - 3.8 cm)

1" (2.54 cm)

Gravity Drain System

Connect the ice maker drain to your drain in accordance with all state and local codes and

ordinances. If the ice maker is provided with a gravity drain system, follow these guidelines

when installing drain lines. This will help keep water from flowing back into the ice maker

storage bin and potentially flowing onto the floor, causing water damage.

■

Drain lines must have a minimum of

⁄8" (15.88 mm) inside diameter.

■

Drain lines must have a 1" drop per 48" (2.54 cm drop per 122 cm) of run or

⁄4" drop per

12" (6.35 mm per 30.48 cm) of run and must not have low points where water can settle.

■

The floor drains must be large enough to accommodate drainage from all drains.

■

The ideal installation has a standpipe with a 1

⁄2" (3.81 cm) to 2" (5.08 cm) PVC drain

reducer installed directly below the outlet of the drain tube as shown. You must maintain a

1" (2.54 cm) air gap between the drain hose and the standpipe.

IMPORTANT: A drain pump is necessary when a floor drain is not available. A Drain Pump kit, Part

Number 1901A, is available for purchase.

Drain Pump System (on some models)

IMPORTANT:

■

Connect the ice maker drain to your drain in accordance with the International Plumbing Code and

any local codes and ordinances.

■

The drain pump discharge line must terminate at an open sited drain.

■

Maximum rise 10 ft (3.1 m)

■

Maximum run 100 ft (30.5 m)

NOTES:

■

If the drain hose becomes twisted and water cannot drain, your ice maker will not work.

■

It may be desirable to insulate the drain line thoroughly up to the drain inlet. An Insulation Sleeve

kit, Part Number W10365792, is available for purchase.

DRAIN CONNECTION

A. Drain hose

B. 1" (2.54 cm)

air gap

C. PVC drain

reducer

D. Center of drain should be 23" (58.4 cm)

from front of door, with or without the

⁄4" (1.91 cm ) panel on the door. The

drain should also be centered from left

to right (7

⁄16" [18.56 cm] from either

side of the ice maker).

A. Recommended location for

electrical and plumbing fixtures.

B. Floor level