Installation Guide

Hanger
Bracket
x2
Gasket
No Gap
at Top
Bolt
Hanger
Bracket
Barrel
Nut
x2
Door-Frame Holes
Screw
Roller
#8-32 x 3/8"
Uncoated Side
Lay flat.
#8-18 x 3/8"
Uncoated
Side
Screw
Outside
Panel Leg
Label
#8-32 x 3/8"
x2
Roller
Lower the glass.
Raise the glass.
Screw Cover
#8-18 x 3/8"
1/16"
Spacers
1/4"-20 Screw
Door
Panel
Towel Bar
x2
Bath Interior
1/32" (1 mm)
Cut Line
"B" Mark
B
B
Top Track
Reversible
Troubleshooting
Symptom: Alignment Recommended Action
1. Top of the door panel is tilted away from the
wall.
A. Remove the door panel from the top track and lower the roller that is closest to the wall. See step 20.
2. Bottom of the door panel is tilted away from
the wall.
A. Remove the door panel from the top track and raise the roller that is closest to the wall. See step 20.
3. Door panel does not touch the bumper. A. Determine whether door panel top or bottom is closer to the wall, and then adjust the roller closest to the wall.
Symptom: Water Leaks Recommended Action
1. Water leaks between panels. A. When showering, make sure the inside panel is against the showerhead wall.
2. Water leaks between the wall jamb and
the door panel.
A. Adjust the door panel to line up with the wall jamb.
3. Water leaks under the bottom track. A. Check for proper silicone sealant application. See steps 23 and 24. Apply more silicone sealant in the leak location.
4. Water leaks around the wall jamb area. A. The notched wall jamb fits over the bottom track to cover any miscut or skewed cuts. Seal as directed to ensure
proper watertight seal. See step 24.
Symptom: Operation (open/close) Recommended Action
1. Outside panel is difficult to move. A. Ensure a gap exists between the bottom track and the door panel. If no gap exists, lower the rollers to the next hole.
B. Ensure the panel is properly engaged over the bottom track. See step 19.
C. Ensure the rollers are properly installed. See steps 18 and 19.
D. Clean any debris in the top track groove.
2. Inside panel is difficult to move. A. Ensure a gap exists between the bottom track and the door panel. If no gap exists, lower the rollers to the next
hole.
B. Ensure the inside-panel guide is properly secured to the bottom frame screws. See step 21.
C. Ensure the rollers are properly installed. See step 20.
D. Clean any debris in the top track groove.
Measure distance “B” above the wall jambs.
Subtract 1/32” (1 mm) or the width of a saw
blade from “B.” Mark and cut the top track.
Position the top track over the wall jambs. Either
side of the top track may face out.
For both doors, slide a gasket over the top of the
glass panel and into each mounting hole. Press
the hanger bracket over the gasket and align the
hanger brackets with the mounting holes.
While pressing downward on the hanger
brackets, use screwdrivers to thread the bolt into
the barrel nut. Tighten until the hanger brackets
are secured firmly in place.
On the inside panel, assemble a roller to the
middle hole of each hanger bracket. Place the
rollers on the same side as the door frame holes.
Lay the inside panel flat and partially thread the
screws into the panel.
Lift the inside panel onto the inside track. The
label faces the outside of the shower.
On the outside panel, assemble a roller to the
middle hole of each hanger bracket. Place the
rollers on the same side as the outside panel leg.
Lift the outside panel onto the outside track. The
label faces the outside of the shower. The outside
panel leg fits over the bottom track leg.
If either panel needs adjustment, remove the
door and position the rollers in new holes to
raise or lower the glass.
Install the inside panel guide onto the partially
threaded screws. The inside panel guide fits into
the bottom track slot. Install screw covers over
the side screws.
Assemble both towel bars with a spacer on each
side of the door panel. Use a hex wrench to
tighten the screws. Do not overtighten!
Outside the shower, use silicone sealant to seal
along the entire length of the wall jambs and the
bottom track.
Inside the shower, use silicone sealant to seal
along the entire length of the wall jambs where
the wall jambs meet the bottom track.
21204880-2-D ©2015 Kohler Co.
11 12
17
22
24
13
1816
21 23
14
19
15
20
Warranty
ONE-YEAR LIMITED WARRANTY
KOHLER plumbing products are warranted to be free of defects in material and workmanship for one year from
date of installation.
Kohler Co. will, at its election, repair, replace or make appropriate adjustment where Kohler Co. inspection discloses
any such defects occurring in normal usage within one (1) year after installation. Kohler Co. is not responsible for
removal or installation costs. Use of in-tank toilet cleaners will void the warranty.
To obtain warranty service contact Kohler Co. either through your Dealer, Plumbing Contractor, Home Center or
E-tailer, or by writing Kohler Co., Attn.: Customer Care Center, 444 Highland Drive, Kohler, WI 53044, USA, or
by calling 1-800-4-KOHLER (1-800-456-4537) from within the USA and Canada, and 001-800-456-4537 from within
Mexico, or visit www.kohler.com within the USA, www.ca.kohler.com from within Canada, or www.mx.kohler.
com in Mexico.
IMPLIED WARRANTIES INCLUDING THAT OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY LIMITED IN DURATION
TO THE DURATION OF THIS WARRANTY. KOHLER CO. AND/OR SELLER DISCLAIM
ANY LIABILITY FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states/provinces do
not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of special, incidental or
consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific
legal rights. You may also have other rights which vary from state/province to state/province.
This is Kohler Co.’s exclusive written warranty.