Installation Guide
Bypass Shower and Bath Doors
K-706000, K-706001, K-706002, K-706003, K-706004, K-706005, K-706006, K-706008, K-706009, K-706010, K-706011, K-706012, K-706013, K-706014, K-706015
Installation Guide
*Call Customer Care Center to order replacement parts.
**Finish/color code must be specified when ordering.
Retain this document for future servicing.
Record model number from box for reference.
Parts Identification
Required Tools
Model Number:______________
11201264-2-B
1
Measure distance "A." Subtract 1/4" (6 mm) from "A"
and cut the threshold.
7
Mark 1" (25 mm) down inside each wall jamb. Remove
the wall jambs.
2
Position the threshold at least 2-1/2" (64 mm) from the
inside ledge. Ensure parallel on the ledge and centered
between the walls. File the ends to match radius corners.
3
Apply 100% silicone sealant to the bottom of the
threshold. Tape in place toward the front of the ledge.
Drill a 9/64" hole and install the wall jamb screw,
leaving 1/8" (6 mm) out.
8
6
Position the wall jambs over the threshold. Plumb and
tape in place.
CAUTION: Risk of injury. Do not attempt to cut
tempered glass.
IMPORTANT! Do not cut the header the same length
as the threshold.
IMPORTANT! Walls must be within 3/8" (10 mm) of
plumb. This unit will not function properly if the walls
are more than 3/8" (10 mm) out of plumb.
Cover the drain with tape to avoid loss of small parts.
Follow the silicone sealant manufacturer's instructions
for application and curing time.
Bypass Shower DoorsBypass Bath Doors
100% Silicone Sealant Masking Tape
32 Teeth Per Inch Blade
Miter Box
9/64"
5/16" Masonry Bit for Tile
5/16"
1/4"
(6 mm)
Cut Line
"A" Mark
A
A
Tin Snips
1048208-C
1048208-W
1042520-F
Screw
1197564-01** [60" (1524 mm)]
1197564-02** [48" (1219 mm)]
Header
1077762
Anchor
1185260
Inside Roller
(#8-18 x 1-1/2")
(#8-18 x 3")
Screw
1198328-A
1198328-B
(#10-24 x 1-1/4")
(#10-24 x 1-3/8")
Screw
1057704-01
1057704-03
[24" (610 mm)]
[18" (610 mm)]
Towel Bar
1185293** (1/4")
1185349** (3/8")
Center Guide
1093027
Washer (8 ea.)
1049033-D
Screw
1197566-01**
Retainer
1187908**
Roller Cap
#10-16 x 1-1/2"
1049043-D
Screw
1181060**
Wall Jamb Cap
1208955**
Clip
1195781**
Roller Plug
1188940-01**
Cleat
1186360**
Bumper Cover
1182686-01** [58" (1473 mm)]
1182686-02** [70" (1778 mm)]
1182686-03** [56" (1422 mm)]
1182686-04** [78" (1981 mm)]
Wall Jamb
1187908**
Roller Cap
1198345
Outside
Roller
1183338-01** [58" (1473 mm)]
1183338-02** [78-1/4" (1988 mm)]
Seal
1"
(25 mm)
Inside Door Panel*
Outside Door Panel*
#10-16 x 1-1/2"
x2
1/8"
(3 mm)
x2
1179922-01** [60" (1524 mm)]
1179922-02** [48" (1219 mm)]
1179922-03** [40-7/8" (1038 mm)]
Threshold
#8-18 x 3/8"
#6-20 x 1/4"
5/32"
x2
1198346**
Skin Pack
Outside Roller Inside Roller Roller Cap Roller PlugClipScrew
#10-24 x 1-3/8"
Screw
#10-24 x 1-1/4"
Anchor Bumper
Screw
#10-16 x 1-1/2"
Screw
#8-18 x 1-1/2"
Screw
#8-18 x 3"
Screw
#8-18 x 3/8"
1185731**
Bubble Pack
1187796**
Handles with
Templates
5
Important! The threshold and wall jamb must be
plumb with the ledge and wall. Position the wall jamb
over the threshold. Trim and file the ends to match
radius corners.
1206630** (1/4" Center Guide)
1206631** (3/8" Center Guide)
Skin Pack
x2
9
Slide the wall jamb up over the screw, then down onto
the threshold. Important! The jamb must be tight
against the wall. Adjust the screw as needed.
4
Mark the center of the threshold. Apply 100% silicone
sealant to the bottom of the guide. Align and rotate the
guide down on the center mark. Tape in place.
Cleat
Screw
#6-20 x 1/4"
Center
Guide
Wall Jamb
Cap
2-1/2"
(64 mm)
USA/Canada: 1-800-4KOHLER
Mexico: 001-800-456-4537
www.kohler.com