Installation Guide

21201264-2-B
TROUBLESHOOTING
Recommended Action
A. Remove the roller caps. Loosen the roller screw and rotate the roller cams. Tip: use the roller cap to rotate the cam.
See steps 16, 17, and 24.
A. Remove the roller caps. Loosen the roller screw and rotate the roller cams. Tip: use the roller cap to rotate the cam.
See steps 16, 17, and 24.
A. Determine whether door panel top or bottom is closer to the wall, and then adjust the roller closest to the wall.
Recommended Action
A. When showering, make sure the inside panel is against the showerhead wall.
A. Adjust the door panel to line up with the wall jamb.
A. Check for proper silicone sealant application. See step 29. Apply more silicone sealant in the leak location.
A. The notched wall jamb fits over the bottom track to cover any miscut or skewed cuts. Seal as directed to ensure proper
watertight seal. See step 29.
Recommended Action
A. Ensure a gap exists between the guide and the door panel. If no gap exists, lower the rollers.
B. Ensure the panel is properly engaged over the bottom track. See step 19.
C. Ensure the rollers are properly installed. See steps 16 and 17.
D. Clean any debris in the header tracks.
A. Ensure the clips are straight and not rubbing on the header. See step 17.
B. Ensure the roller screws are completely tightened. See step 17.
C. Ensure retainer is securely attached. See step 20.
Symptom: Alignment
1. The top of the door panel is tilted away from the wall.
2. The bottom of the door panel is tilted away from the wall.
3. The door panel does not touch the bumper.
Symptom: Water Leaks
1. Water leaks betwen panels
2. Water leaks between the wall jamb and the door panel.
3. Water leaks under the threshold.
4. Water leaks around the wall jamb area.
Symptom: Operation (open/close)
1. The inside and/or outside panel is difficult to move.
2. Rubbing noise during panel movement.
© 2013 Kohler Co.
19
27
2220
13
29
2825
24
21
18
15
14
Measure distance "B" between the cleat legs.
Important! Position the screws at the dimensions
shown. Drill 5/32" holes into the retainer. Slide the
retainer between the panels. Secure to the header with
six screws.
ONE-YEAR LIMITED WARRANTY
KOHLER plumbing products are warranted to be free of defects in material and workmanship for one year from
date of installation.
Kohler Co. will, at its election, repair, replace or make appropriate adjustment where Kohler Co. inspection discloses
any such defects occurring in normal usage within one (1) year after installation. Kohler Co. is not responsible for
removal or installation costs. Use of in-tank toilet cleaners will void the warranty.
To obtain warranty service contact Kohler Co. either through your Dealer, Plumbing Contractor, Home Center or
E-tailer, or by writing Kohler Co., Attn.: Customer Care Center, 444 Highland Drive, Kohler, WI 53044, USA, or by
calling 1-800-4-KOHLER (1-800-456-4537) from within the USA and Canada, and 001-800-456-4537 from within
Mexico, or visit www.kohler.com within the USA, www.ca.kohler.com from within Canada, or www.mx.kohler.com
in Mexico.
IMPLIED WARRANTIES INCLUDING THAT OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE EXPRESSLY LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. KOHLER
CO. AND/OR SELLER DISCLAIM ANY LIABILITY FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES. Some states/provinces do not allow limitations on how long an implied warranty lasts, or the
exclusion or limitation of special, incidental or consequential damages, so these limitations and exclusions may not
apply to you. This warranty gives you specific legal rights. You may also have other rights which vary from
state/province to state/province.
This is Kohler Co.'s exclusive written warranty.
Important! Do not cut the header too short. Add 1" (25
mm) to "B" and cut the header and retainer.
Rotate the header in place and secure to each cleat with
two self-drilling screws.
With help, lift the inside panel over the guide and into
the track. Ensure the rollers operate smoothly. Refer to
the Troubleshooting table as needed.
With help, lift the outside panel onto the track and over
the guide. Ensure the rollers operate smoothly. Refer to
the Troubleshooting table as needed.
Apply 100% silicone sealant to the back of the bumper.
Open the bumper and install over the cleat. Press tight
to engage the tabs.
Towel bar models: assemble the towel bars with a
spacer on each side of the door panel. Use a hex wrench
to tighten the screws. Do not overtighten!
Handle models (continued): align the top of the
template with the mark. Remove the adhesive backing
and align the handle with the template.
Snap a cap on each of the four rollers. Install two roller
plugs on the outside panel rollers, with the slots down.
Remove the adhesive backing from the seal. On the side
closest to the showerhead, attach the seal to the shower
side of the wall jamb.
Apply a small bead of 100% silicone sealant to the
underside of the wall jamb cap. Press the cap onto the
wall jamb.
Apply 100% silicone sealant along the wall jambs inside
and outside the shower, and apply along the threshold
outside the shower.
11 12
Drill 5/16” holes at the two diagonal cleat marks. Insert
anchors.
Important! The cleat must be level and plumb with the
wall jamb. Align the cleat with the wall jamb and secure
with two screws.
1
2
3
#8-18 x 1-1/2"
#8-18 x 3" (for wall units)
x2
x2
x2
Align a cleat with the top of the jamb and mark two
holes diagonally.
10
17
Outside panel: install an outside roller, clip, and screw
in each upper hole. Ensure the clip is vertical.
16
Inside panel: install the inside rollers and screws in the
upper holes.
23
Handle models: mark distance "C" on the glass. Use
alcohol wipes to clean the glass at the handle installation
location. Ensure the inside panel is closest to the
showerhead.
26
Trim the wipe seal to the height of the wall jamb.
Slot
x4
x2
x2
Bath:
C = 21" (533 mm)
Shower:
C = 37-1/2" (953 mm)
C
C
B
Cut Line
"B" Mark
1"
(25 mm)
HeaderRetainer
#8-18 x 3/8"
x2
Spacers
1/4"-20 Screw
x2
x2
#6-20 x 1/4"
6"
(152 mm)
1-1/2"
(13 mm)
12" (305 mm)
x2
Outside Panel
Install
vertically.
3-1/8"
(79 mm)
x2
Inside Panel
5-1/2"
(140 mm)
(#10-24 x 1-1/4")
(#10-24 x 1-3/8")
(#10-24 x 1-1/4")
(#10-24 x 1-3/8")
Label on this
Side of Glass
Label on this
Side of Glass
B