Installation Guide

Top View
Showerhead
Strike Side
Top View
Showerhead
Strike Side
Right Pivot Left Pivot
Handle
Pivot Side
Handle
Pivot Side
A
Stop
Showerhead
Wall Jamb
Outside
Stop
Level
#8-18
x 2"
1
2
3
Adjustment Clamp
Wall Jamb
#8-18
x 3/4"
Tall Side of the
Bottom Track
A
Adjustment
Clamps to the
Inside of the
Shower
Sealant
5/16"
5/16" Tile Bit
100% Silicone Sealant
Masking Tape
32-Teeth Per Inch Blade
Miter Box
Tin Snips
Pivot Shower Doors
1035084**
1035083**
1034805-01**
1077762
1048208-N
RH Wall Jamb Cover
Screw
Wall Anchor
Wall Jamb
1019420**
Strike Jamb Cover
1018459**
1019934-01**
867201
1036966-01**
Strike Jamb
1013641-01**
1035917**
1048208-B
(Silver)
Hinge Jamb Cover
Hinge Jamb
Panhead Screw
Series
Number Label
Handle
Bottom Track
Clamp
1034805-01**
Wall Jamb
LH Wall
Jamb Cover
1113196-01**
(K-702416)
Hinge
1036986-01**
1113195-*-**
(K-702416)
Door Panel Assembly
1019386-A
(Bronze)
1021020
1036961-*-**
1036958-*-** (K-702400)
1036960-*-**
1036959-*-**
(K-702406)
(K-702404)
(K-702402)
1036965-*-**
1036964-*-**
1036963-*-**
1036962-*-**
(K-702414)
(K-702412)
(K-702410)
(K-702408)
Latch
1017115**
1037048-01**
(K-702400)
1037047-01**
1037046-01**
(K-702406)
(K-702404)
(K-702402)
1037052-01**
1037051-01**
1037050-01**
1037049-01**
(K-702414)
(K-702412)
(K-702410)
(K-702408)
Screw
1019386-B
Bulb Seal
(Silver)
(Brass)
1019386-C
Key
(3/32" Hex)1019972
(5/64" Hex)1013942
(K-702408)
(K-702410)
(K-702412)
(K-702414)
1014086-05
1014086-06
1014086-07
1014086-08
(K-702402)
(K-702404)
(K-702406)
1014086-02
1014086-03
(K-702400)
1014086-01
1014086-04
(K-702416)
1014086-13
1019387-A
(Bronze)
Screw
1019387-B
(Silver)
(Brass)
1019387-C
Threshold Seal
1036384**
Hardware Skin Pack
Level
1
1218632-2-A
USA/Canada: 1-800-4KOHLER
Mexico: 001-800-456-4537
www.kohler.com
1218632-2-A
Installation Guide
K-702400, K-702402, K-702404, K-702406, K-702408, K-702410, K-702412, K-702414, K-702416 Pivot Shower Doors
*Call Customer Care Center to order replacement parts.
**Finish/color code must be specified when ordering.
Retain this document for future servicing.
Record model number from box for reference.
Model Number:______________
1
Required Tools
Parts Identification
2
7 865
43
9
CAUTION: Risk of personal injury. Do not
attempt to cut tempered glass. Unframed tempered
glass should not contact the floor or other hard surfaces
or it may shatter.
• Walls must be within 3/8” (10 mm) of plumb.
• Cover drain with tape to avoid loss of small parts.
• Follow the silicone sealant manufacturer’s
instructions for application and curing time.
Determine either a right or a left door pivot.
The door handle installs on the same side as the
showerhead.
Loosely attach four adjustment clamps to each
wall jamb with flathead screws. Use the hex
wrench provided. Do not tighten the screws at
this time.
Center the wall jambs on the threshold and
check the fit. If needed, snip and file the bottom
edges of the wall jambs for a snug fit.
Using a level, plumb both wall jambs. Secure
with masking tape. Mark the screw holes and
the front edges of the wall jambs.
Remove the wall jambs. Drill 5/16” holes and
insert anchors in both shower walls. For tile, use
a 5/16” tile bit. Anchors will work in wall studs.
Realign and plumb both wall jambs. Secure with
screws.
At the threshold, measure from the first stop on
the inside of the strike wall jamb to the first stop
on the inside of the hinge wall jamb (Dimension
“A”).
Cut the bottom track to dimension “A.” Smooth
the cut edge with a file. Verify bottom track fit
between the wall jambs so the tall side of the
bottom track is to the outside.
Apply silicone sealant along the groove on the
underside of the bottom track.