User Manual

6. SETTINGS / ERRORS
USER INSTRUCTIONS / FUNCTIONS
4. FIXING CABLES
The mounting of the cable ties (= Velcro tapes) is
pictured and described in Section 2.9.
4.1 Fix the cable along the tube
4.2 Wrap the loose end of the Velcro around the cable
4.2 and press. Depending on how close the Velcro is
4.2 fitted, the result will be a loose respectively a tight
4.2 fit of the cables.
5. DIMENSIONS
HEIGHT: 600 - 1020 mm (in 15 mm increments)
STAND: width 975mm, depth 575 mm
SUPPORT: width max. 784 mm, depth 340 mm
TRANSPORT: 950 x 575 x 180 mm
6. SETTINGS / ERRORS
Incorrect settings may compromise the security of
the installation and must be corrected:
6.1 The longer part of the support arms must not be
6.1 placed across the short part of the base tubes.
6.2 The two supports should not be placed off-centre
6.2 (x:y), but symmetrically to the middle (x:x).
6.3 Both stand tubes must always have equal heights
6.3 (see chapter 3).
Unscrew clamping
screw h slightly
3. HEIGHT ADJUSTMENT
3. of the BASE TUBES
Recommended procedure is to adjust
one tube after the other by :
3.1 Turning the keyboard table over and
3.1 placing it on the supports
3.2 Loosen clamping screw h slightly
3.3 Pull handle of the clamping screw
3.4 Extend respectively retract base tube
3.5 Engage the bolts and
3.5 tighten the clamping screw
NOTE:
For reasons of security both base tubes
must always have the same height.
CHECK, MAINTAIN
- Incorrect settings during maintenance can cause
- health hazards arising from: -edges, -loosened threads,
- -movable parts, etc. To avoid this, take due care and
- work where necessary with protective equipment
- (e.g. gloves)
- Clean with a damp cloth. Do not use abrasive
- cleaning agents
FAULT-FINDING (F) and REPAIR (R)
F: The base cannot be fully unfolded
F: R: Unscrew the clamping screw until the thread no
F: R: longer protrudes into the inside of the tube (2.14)
F: Keyboard table wobbles
F: R: Check screw connections and surface
F: Keyboard table stands lopsided
F: R: Adjust base tubes to same height (see 6.3)
F: Instrument is off-centre
F: R: Correct position of support arms if
F: R: necessary (6.1 and 6.2)
Pull handle until the
safety bolts are no
longer engaged
Keep handle pulled
and retract or
extend the tubes
Click safety bolt in the
desired borehole and
retighten clamping screw
The height of the table can be adjusted in
29 steps with a distance of 15 mm each.
Every fourth borehole of the tubes
is marked with a roman numeral;
this making it much easier to adjust
both tubes to the required equal
height.
The STOP
marking
shows the
max.
extraction.
TECHNISCHE DATEN / SPEZIFIKATIONEN
Colour variants 18820-019-55 black, -76 pure white, -91 ruby red
Material
Tubes, angle: steel, powder coated / Screws, washers: galvanized
Plastic parts: PA, PE, PC, TPE
Packaging Single carton: 960 x 620 x 59 mm
Weight 9.8 kg
Accessories
(optional)
18811 Stacker 1, 18822 Stacker 2, 18814 Adapter, 18805 Sheet music and concept holder,
18817 Universal holder, 18815 Laptop holder, 18806 Trolley for Keyboard Stands,
18829 Carrying case,197... Tablet PC holders, 211... Boom arms
KÖNIG & MEYER GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
18820-019-55/76/91 Rev.04 03-80-384-00 4/19