Commercial Undercounted Ice Machine Instruction Manual Model: CIM198 CIM265 Thank you for purchasing our product! Before returning to retailer, if you are having trouble with your unit, for assembly assistance, missing or damaged parts. Please contact customer service Phone: 718-576-6342 Email: support@koolmore.com We are here to help.
CONTENTS IMPORTANT SAFETY-------------------------------------------------------------------------------------3 SPECIFICATION--------------------------------------------------------------------------------------------5 DIMENSION/CONNECTION---------------------------------------------------------------------5 RATING------------------------------------------------------------------------------------------------5 GENERAL INFORMATION-------------------------------------------------------------------------------
IMPORTANT SAFETY When using electrical appliances, basic safety precautions should be followed to reduce the risk of fire, electric shock, and injury to persons or property. Read all instructions before using any appliance. Use this appliance only for its intended purpose as described in this owner’s manual. This ice-maker must be properly installed in accordance with the installation instructions before it is used. This unit must be positioned so that the plug is accessible.
– – – – – – WARNING: Do not damage the refrigerant circuit. WARNING: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. WARNING: Children should be supervised to ensure that they do not play with the appliance. WARNING: This appliance must be earthed.
SPECIFICATIONS 1) DIMENSIONS/CONNECTIONS Water Drainage Port Water Inlet Port 2) Rating POWER SUPPLY VOLTAGE 1Phase, 110-120/60Hz MODEL CIM198 CIM265 CLIMATE CLASS 10-40℃ 10-40℃ ELECTRICAL PROTECTION CLASS I I ICE MAKING RATING (Amps) 4.4 Amp 7.5Amp ICE HARVEST RATING (Amps) 5.0 Amp ICE MAKING CAPACITY (KG/24H) 90kg/24Hour REFRIGERANT CHARGE R290 3.67Oz / 104g R290 3.
GENERAL INFORMATION 1) Ice-making and its water tank parts 6 A. Water dividing pipe ： with nine little holes, water will flow out from these little holes. And if no water flows out, can be disassembled and cleaned. B. Evaporator (ice-making module) C. Ice full detecting board: Use to detect the inner cabinet is full of ice or not, and to check the the ice-harvest process is over or not.
2) Operation panel A．“TIMER CLEAN”button： Quickly press this button once, to enter the Timer setting program; And press this button for more than 5 seconds, to enter the Cleaning program. TIMER B．“ON/OFF”button： CLEAN When the unit is off, press this button to turn on the unit; And during the Self-cleaning program, or normal ON/OFF ice-making state, press this button to turn off the unit at once; And also if the unit is set with the Timer, press this button to cancel the Timer setting.
OPERATING PROCEDURES & MAINTENANCE UNPACKING YOUR ICE MAKER 1. Remove the exterior and interior packaging. Check if all the accessories, including instruction manual, ice scoop, white water inlet pipe, 4 ways to 2 ways water quick connector and the water draining pipe, etc., are inside or not. If any parts are missing, please contact our customer service. 2. Remove the tapes for fixing the door and inner cabinet, ice scoop, etc.. Roughly clean the inner cabinet & ice scoop with wet clothe. 3.
Choose a well-ventilated area with temperatures above 50 Fahrenheit and below 90Fahrenheit. This unit MUST be installed in an area protected from the elements, such as wind, rain, water spray or drips. The ice maker requires a continuous water supply with pressure 1-8 Bar as required in above specification table. The temperature of the water feeding into the ice maker should be between 41Fahrenheit and 77Fahrenheit for proper operation.
ice-cube made by the first ice making cycle after cleaning. 4. The outside of the ice maker should be cleaned regularly with a mild detergent solution and warm water. 5. Dry the interior and exterior with a clean soft cloth. WATER CONNECTION FOR YOUR ICE MAKER Important: Be sure to use the new hose-sets supplied with the appliance to connect to water mains and that old hose-sets should not be reused.
OPERATION YOUR UNIT Operation button and display area diagram OPERATION AREA DISPLAY AREA OPERATION AREA + TIMER CLEAN - ON/OFF Operation the ice-making process 1.
4. When the symbol lights up，the machine stop working,it will work again after you take out the ice. 5. Shut down the unit： During the unit making ice，press the“ON/OFF”button on the control panel，the unit shut down and into standby mode.If you press "ON/OFF" longer than 5S during ice making, then the unit enters the deicing process directly, this function can help remove the ice on the ice plate. Press "ON/OFF" to shut down the machine. 6.
WIRING DIAGRAM ELECTRICAL DIAGRAM COMPRESSOR N L G Power Supply Start Relay MW M AW~ LCD Overload Protector AC-L AC-N VALVE COMP PUMP AC Water Pump Relay DC Fan Motor Solenoid Vale for Ice-harvest WATER Main Control PCB T1 RT DC Water Inlet Valve WATER LEVEL DETECTING SWITCH T1 SENSOR FOR AMBIENT TEMP MCU ICE SENSOR FOR ICE FULL DETECTING 6C Normal Sounds Your new ice maker may make sounds that are not familiar to you. Most of the new sounds are normal.
Preparing the Ice Maker for Long Storage If the ice maker will not be used for a long time, or is to be moved to another place, it will be necessary to drain out all of the water in the system. 1. Allow all of the ice cubes have been ejected from the evaporator of ice maker. 2. Turn off the unit, and unplug the power cord. 3. Shut off the water supply at the main water supply. 4. Disconnect the water supply hose from the water inlet valve. 5.
What shouldn't be done Never keep anything in the ice storage bin that is not ice: objects like wine and beer bottles are not only unsanitary, but also it’s labels may slip off and obstruct the drain pipe. Exterior Cleaning The door and cabinet may be cleaned with a mild detergent and warm water solution such as 28g of dish washing liquid mixed with 7.5L of warm water. Do not use solvent-based or abrasive cleaners. Use a soft sponge and rinse with clean water.
3、 When there are ice cubes on the surface of the evaporator, but can’t fall down easily, do not use the mechanical substance to remove it by force; Only press the “ON/OFF” button for more than 5 seconds, the unit will enter the ice melting process, after some while, the big ice-cubes will fall down, then turn off the unit and unplug the power cord to clean the surface of the evaporator. 4.
Ice Making Assembly System Cleaning by Using Nu-Calgon Nickle Safe Ice-machine Cleaner Minerals that are removed from water during the freezing cycle will eventually form a hard scaly deposit in the water system. Cleaning the system regularly helps remove the mineral scale buildup. How often you need to clean the system depends upon how hard your water is. With hard water of 4 to 5 grains/liter, you may need to clean the system as often as every 6 months. 1. Turn off the ice maker.
The ice machine cleaner contains acids. DO NOT use or mix with any other solvent-based cleaner products. Use rubber gloves to protect hands. Carefully read the material safety instructions on the container of the ice machine cleaner. DISCARD the first batch of ice troduced after cleaning. 8. Then open the water faucet of the main water supply, Let the water flow in the unit. Again press the“TIMER CLEAN”button on control panel for more than 5 seconds, to enter the self-Cleaning program.
NORMAL TROUBLE SHOOTING Problem Possible Cause Check the main water supply pressure or check the water supply hose is blocked or not, adding the water pressure or cleaning the hose necessary. No water supply The whole “ ” symbol is always on.
ERROR INDICATOR a) Ambient temp sensor breakdown----- Display E1 in digital window. b) The machine not make ice or the gas leak ----Display E2 in digital window c) Magnetic control switch cut off----“Full”light will be on when plugging on or just turning on the unit. And it will delete the breakdown display if this switch is electric shorted. d) During the ice making process, press the “ON/OFF” button for more than 5 seconds, the unit Start to enter the ice harvest program.
If you are experiencing any issue with your unit, please contact us right away. Phone: 7 1 8 -756-6342 Email: support@koolmore.com Limited Service Warranty Valid only in the Continental United States 1 Year Parts and Labor Warranty Unless otherwise stated, Koolmore Supply Inc warrants to the original purchaser of new Koolmore Refrigeration units, that such equipment will be free from defects in material and workmanship for a period of 1 year from the date of delivery.
