User Manual
Table Of Contents
- Table of Contents
- Introduction
- Preparations
- Quick Start
- Editing
- Editing a synth program
- The structure of a synth program
- 1. VOICE — SYNTH/VOCODER
- 2. PITCH — SYNTH/VOCODER
- 3. OSC1 (Oscillator 1) — SYNTH/VOCODER
- 4. OSC2 (Oscillator 2) — SYNTH
- 5. MIXER — SYNTH
- 6. FILTER — SYNTH
- 7. FILTER EG — SYNTH
- 8. AMP (Amplifier) — SYNTH
- 9. AMP EG — SYNTH/VOCODER
- 10. LFO 1, 11. LFO 2 — SYNTH/VOCODER
- 12. PATCH 1, 13. PATCH 2, 14. PATCH 3, 15. PATCH 4 — SYNTH
- Editing a vocoder program
- The structure of a vocoder program
- 1. VOICE — SYNTH/VOCODER
- 2. PITCH — SYNTH/VOCODER
- 3. OSC1 — SYNTH/VOCODER
- 4. AUDIO IN 1 — VOCODER
- 5. MIXER — VOCODER
- 6. FILTER — VOCODER
- 7. FC MOD — VOCODER
- 8. AMP — VOCODER
- 9. AMP EG — SYNTH/VOCODER
- 10. LFO 1, 11. LFO 2 — SYNTH/VOCODER
- 12. CH LEVEL A, 13. CH LEVEL B — VOCODER
- 14. CH PAN A, 15. CH PAN B — VOCODER
- Editing the effects and EQ
- Editing the arpeggiator
- Overall settings (GLOBAL)
- Using the microKORG with other MIDI devices (MIDI)
- Saving Data
- SHIFT functions
- Appendix
- Voice Name List
- Parameter List
- SHIFT Function List
- DEMO Song List
- MIDI Implementation Chart
41
17. DELAY — SYNTH/VOCODER
TYPE [Stereo Delay,
Cross Delay, L/R Delay]
Selects the delay type.
Stereo Delay ( ):
This is a stereo delay.
(➝Figure 17-1)
Cross Delay ( ):
This is a stereo delay where the left
and right channels of feedback are
interchanged. In a Layer program,
it is effective to set the pan of the
two timbres to left and right respec-
tively. (➝Figure 17-2)
L/R Delay ( ):
This is a delay where the delay
sound is output to left and right al-
ternately. (➝Figure 17-3)
TEMPO SYNC [OFF, ON]
Specifies whether the delay time
will be synchronized to the tempo.
OFF ( ):
Delay off (not synchronized). The
delay will operate according to the
"DELAY TIME" value you specify.
ON ( ):
Delay on (synchronized). The delay
will synchronize to the ARPEG.A
"TEMPO" setting or to MIDI Clock
data from an external device.
DELAY TIME [0...127]
Sets the delay time.
This parameter is available only if
"TEMPO SYNC" is OFF.
SYNC NOTE [1.32...1.1]
Specifies the ratio of the delay time
relative to the ARPEG.A "TEMPO"
value. (➝p.65)
This parameter is available only if
"TEMPO SYNC" is ON.
DELAY DEPTH [0...127]
Specifies the delay depth and feed-
back amount. Increasing this value
will make the delay louder and will
also increase the amount of feed-
back.
If you do not wish to apply a delay,
set this to 0.
Excessively high settings of this
parameter may cause the output
to be distorted.
Stereo Delay
DELAY
FEEDBACK
FEEDBACK
DELAY
Cross Delay
DELAY
FEEDBACK
FEEDBACK
DELAY
L/R Delay
DELAY
FEEDBACK
FEEDBACK
DELAY
Figure 17-1 Figure 17-2 Figure 17-3
The delay effect simulates the delays that occur when sound travels through air.
"TYPE" (knob 1 ) selects the type of delay effect. "DELAY DEPTH" (knob 4 ) sets the delay depth and the amount of feedback. "TEMPO SYNC"
(knob 2 ) specifies whether the delay time will be synchronized to the tempo set by the arpeggiator or by an external MIDI clock.