Installation Sheet

INSTALLATION INSTRUCTIONS
Item#P1359-618 (New. 10/28/2017)
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Page: 1/2
Fig. 1
Fig. 3
LA-2880E
PREPARATION (Fig. 1)
1.
Shut off the power at the fuse box or circuit breaker. If
necessary, remove the old fixture, including the
mounting
hardware.
2.
Carefully remove the fixture from the carton and check that all
parts are included as shown in the illustration.
ASSEMBLING THE FIXTURE WITH CHAIN LOOP (Fig. 1)
3. Determine the desired hanging height and thread rods (F1, F2
and F3) to the nipple (I) of the fixture body. Then attach loop
(H1) by screwing in to rod (F1). No
te: remove the nipple if
installing with one 6” rod only.
4.
Attach the quick link (G) connect to loop (H1) and loop (H2) on
the canopy (D), caref
ully feed the wire over loop (H1), quick
link (G) and loop (H2).
5. Thread screws (A) into the pre-drilled holes in
the circular
strap (B)
spaced the same distance apart as the holes in the
canopy (D).
6.
Attach the circular strap (B) to the Junction box using
mounting screws (C) (Size: #8-32N*L0.5”
). The side of the
circular strap marked “GND” must face out.
7. The support c
able is provided to support the weight of the
fixture while wiring. Align the fixture to circular strap (B) and
attach hook (P) on the end of support cable (R
) into a slot
located on circular strap (B)
. Carefully allow the support cable
to support the weight of the fixture while wiring.
CONNECTING THE WIRES (Fig. 3)
8. At this point, connect the electrical wires as shown in figure 3
,
making sure that all wire connectors are secured.
If your outlet
has a ground wire (green or bare copper), connect the fixture’s
ground wire to it. Otherwise, connect the fixture’s ground wire
directly to the circular strap using the green screw provided.
9. Tuck the wire connectors
neatly into the ceiling Junction Box
and then raise the canopy all the way to the ceiling.
COMPLETING THE INSTALLATION (Fig. 1)
10. Thread canopy (D) into screws (A
), and secure with knurled
knobs (E).
11. Secure rod (K) onto the nipple (L) of the fixture body (J).
12. Install the 16*75W Xenon bulb (N) (included)
in accordance
with the fixture’s specifications. (DO N
OT EXCEED THE
MAXIMUM WATTAGE RATING!). (
NE PAS DEPASSER
LA PUISSANCE NOMINALE MAXIMALE!).
13.
Place the glass shade (O) over the socket and twist to secure
it to the socket cup (M).
Y
our installation is now complete. Return power to the junction
box and test the fixture.
Note:
Illustration (Fig. 1) on this manual is for installation
purposes only. It may or may not be identical to the fixture
purchased.
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
Set# A-020-A
-
Circular Strap
-
Ground Screw
-Mounting Screw*2
Rod# W35-1-618*1(F1)
W35-1-618*2(F2)
W35-H-618*1(F3)
J
L
M
F1
G
H1
H2
E
D
A
C
B
R
F2
F3
I
K
N
O
P
IMPORTANT: FIXTURE SHOULD BE INSTALLED BY
A QUALIFIED ELECTRICIAN TO ENSURE PROPER
WIRING AND INSTALLATION.