Installation Sheet

ManualsBrandsKovacs ManualsChandeliersKovacs Forest Ice 40" Wide Integrated LED Linear Chandelier with Frosted Glass Shade

INSTALLATION INSTRUCTIONS

FOR P1386-077-L

FOR LED Chandelier/Pendant Light

WARNI NG! S HUT P OWER O FF AT F USE OR CIR C UIT B RE AK E R .

AV E R T I S S E M E N T ! C O U P E R L E C O U R A N T A U N I V E A U D E S F U S I B L E S O U D O D I S J O N C T E U R

Page: 1/2

Fig. 2

HANGING THE FIXTURE

1. Carefully remove the fixture from the carton and

check that all parts are included as shown in the

illustration.

2. Shut off power at the circuit breaker and remove old

fixture including the mounting hardware

SUGGESTED INSTALLATION (Fig. 1)

3. Attach the mounting plate (B) to the junction box (A)

using screws (C) (Screw Size: 8-32*1/2”L).The side

of the mounting plate marked “GND” must face out.

4. Disconnect the swivel (D) from the canopy (G) by

loosen key washers (M) and nuts (S).

5. Determine length desired and thread rods (F1,F2，

F3) to housing (N). Carefully thread wires through

rod and swivel. Note: remove the nipple if installing

with 6” (F3) rod only.

6. Thread swivel (D) onto rod, align canopy (G) with

swivel and tighten with key washers (M) and nuts

(S).

CONNECTING THE WIRES (Fig. 1,2)

7. Cut the extra wire if necessary. Connect the driver

output wires (Red to Red; and Black to black) with

fixture making sure that all wires connectors (O) are

secured.

8. Connect the driver input wire with housing wire as

shown in Fig.2, making sure that all wire connectors

(P) are secured.

9. If your outlet box has a green or bare copper ground

wire, connect the fixture’s ground wire to it.

Otherwise, connect the fixture’s ground wire directly

to the mounting plate (B) using the green screw (L)

provided. After wires are connected, tuck them

carefully inside the junction box (A).

COMPLETING THE INSTALLATION (Fig. 1,3)

10. Connect the canopy (G) with the mounting plate

(B) and secure with mounting screws (E).

11. Align the glass (I) to the housing (N), make sure

the hole on the glass match the hole, and tighten it

with screws (F).

12. Install the side cap (J), and tighten it with screws

(K) and washers (R).

For slope ceiling application, rotate swivel at the top

of the stem to ensure luminaries is aiming down

(Fig. 3).

Your installation is now complete. Return power to the

junction box and test the fixture.

CAUTION /ATTENTION: When handling bracket, do not

apply pressure to the LEDs. Hold the metal parts.

Fig.1

Set # A-021-225115

-Mounting Plate

-Ground Screw

-Mounting Screw*2

FIXTURE

WIRES

Black or

Smooth

HOUSE

WIRES

Black

(Hot)

FIXTURE

WIRES

White or

Ribbed

HOUSE

WIRES

White

(Neutral)

FIXTURE

WIRES

Bare

Copper

(Ground)

HOUSE

WIRES

Green

(Ground)

Summary of content (2 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR P1386-077-L FOR LED Chandelier/Pendant Light W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R . AV E R T I S S E M E N T ! C O U P E R L E C O U R A N T A U N I V E A U D E S F U S I B L E S O U D O D I S J O N C T E U R HANGING THE FIXTURE 1. Carefully remove the fixture from the carton and check that all parts are included as shown in the illustration. 2.
PAGE 2
Fig.3 Hardware Bag: F1.Rod 12”*2 Rod# W30-1-077 F2.Rod 12”*4 Rod# W30-1-077 F3.Rod 6” *2 Rod# W30-H-077 Fig.4 Replacing LED module (Fig. 4) The LED module can be replaced by a qualified electrician without cutting of wire and without damage to any decorative element to which the fixture is attached. See installation steps for more details (Fig.4.) a. Shut off power. b. Loosen screws (F) and take off the glass (I) c. Use a pin to stick the hole on the quick connect (Q) to disconnect the wire. d.