I N S TA L L AT I O N MA N UA L Seda™ 8” Widespread 2-Handle Faucet FUS-1823 www.kraususa.com I toll free: 1.800.775.0703 I © 2014-2015 Kraus USA Inc.
Thank you for purchasing Kraus We would like to take this opportunity to thank you for your business with Kraus USA. It is our sincere hope that you are completely satisfied with your experience. We welcome any questions or comments you may have, and will be glad to assist you in the future. For more information about Kraus products, please visit our website at: www.kraususa.
10 1/8” (257mm) 8 5/16” (21mm) ∅ 1 15/16” (∅ 50mm) 1 3/8” (35mm) ∅ 1 3/4” (∅ 45mm) ∅ 1 15/16” (∅ 50mm) Prior to Installation: • Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800775-0703 for a replacement • 9/16”-18UNEF 1 1/4-18UNF-2A Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet.
FUS-1823 Diagram and Parts List B 7A D 8A 7A A I 8B 8C 8D J K 8A 8B 8C C1 C2 C3 E1 8D E2 C1 C2 C3 F H G A. Hot Handle Valve E. Spout Mounting Hardware: B. Cold Handle Valve E1. Rubber & Metal U-Washer C. Hot & Cold Handle Mounting E2. Mounting Nut Hardware: F. T-Union C1. Rubber & Metal Washer G. Hot & Cold Waterlines C2. Mounting Nut H. 3/8 in. OD x 1/2 in. IPS Waterlines C3. Mounting Screws I. Aerator D. Spout J. Aerator Key K.
Faucet Dimensions 2.87” 73mm 4.96” 126mm 1.8” 46mm 2.24” 57mm MAX 1.18” 30mm 1.8” 46mm 4.76” 121mm 4.92” 125mm 5.62” 143mm 4.92” 125mm 1 2 1 1/4-18UN 9/16”-18UNEF Step 1: Remove mounting hardware and T-union A D B 8A 7A 8B 8C D T-union (F) and mounting Remove hardware (E) from spout (D). Remove mounting hardware (C) from hot and cold handle valves (A & B) 7A 1 1/16” ~ 1 5/8” 27mm ~ 41.
2 3 1 1/4-18UNF-2A 9/16”-18UNEF 9/16”-18UNEF Step 2: Install & secure spout Install spout (D) through hole in countertop or sink. Attach rubber & metal U-washer (E1) A and mounting nut (E2). Adjust spout (D) to proper position and tighten mounting nut (E2) with adjustable wrench. Secure C1T-union (F) onto supply line of C2spout (D). Tighten T-union (F) C3 with adjustable wrench D B 1 1/16” ~ 1 5/8” 27mm ~ 41.3mm 1 1/16” ~ 1 5/8” 27mm ~ 41.
Step 4: 4 Connect waterlines to faucet and main valve 2 3 1 1/4-18UNF-2A 9/16”-18UNEF 9/16”-18UNEF B A 7A AH 8A 8B 8C 8D F E1 E2 F C1 HC2 C3 H G G 1 1/16” ~ 1 5/8” 27mm ~ 41.3mm D Secure hot & cold waterlines (G) to hot and cold valves (A & B) (HandTighten Only). Thread other end of waterlines to T-union (F).B Attach 3/8 in. OD x 1/2 in. IPS waterlines (H) to copper pipe on valves A. Hot Side: Left B. Cold Side: Right Secure other end of waterlines to angle stops.
Replacement Part List - FVS-1823 1 4 3 10 2 18 14 11 5 12 15 13 6 16 17 7 8 9 19 1. Hot Handle 11. Rubber & Metal U Washer 2. Cold Handle 12. Mounting Nut 3. Set Screw 13. T-Union 4. Cover Button 14. Cold Cartridge 5. Hot Cartridge 15. Cold Valve 6. Hot Valve 16. Hot & Cold Waterlines 7. Rubber & Metal Washer 17. 3/8 in. OD x 1/2 in. IPS Waterlines 8. Mounting Nut 18. Aerator Key 9. Mounting Screw 19. Hex Wrench 10.
Trouble - Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: 10 PROBLEM CAUSE ACTION Hexagon Nut 9 11 Leakage under the handle Hot or cold cartridge (5 or 14) may be loose 12 13 Remove cover button (4). Loosen set screw (3) with hex wrench (19). Remove handle (1 or 2).
Codes/Standards Applicable: NSF/ANSI 372 GREEN LEAD FREE IA P MO R &T NSF/ANSI 61 ASME A112.18.1M 1.5GPM 5.7L/min maximum TM Water Efficiency KRAUS LIMITED LIFETIME WARRANTY This product has been manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”). We offer our customers thoughtfully crafted fixtures & accessories, engineered for enduring performance over years of use. WHO IS COVERED BY THE WARRANTY This warranty extends to the original purchaser only.
C. Kraus recommends installing all Kraus products with a licensed, professional plumber. Kraus will not be held responsible for any damage or product failure due to improper installation, misuse, or failure to use a licensed professional. Please read your care and maintenance documentation to determine the limits of proper use. D. Commercial use will automatically void this warranty. E. This warranty is not applicable to Kraus products purchased from an unauthorized seller.
www.kraususa.